Having problems with your Dishwashers ?

Hi! when the machine is switched on, it displays " CODE 1--- " and on touching the on button all of them go on then off. Only the cycle one button indicator that lights very deem. What could be the problem


Answers :

Could be the thermal cutoff fuse or the touch pad or a bad erc would need to do some power and continuity tests with a multimeter to assure which piece is working properly and which is not would need the model number for your unit to provide schematic of your unit if you have any further questions message me back and please remember when our chat has fully concluded to rank how this opinion has helped it allows me to help others in similar situations Thanks Rick
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi! when the machine is switched on, it displays " CODE 1--- " and on touching the on button all of them go on then off. Only the cycle one button indicator that lights very deem. What could be the problem


Could be the thermal cutoff fuse or the touch pad or a bad erc would need to do some power and continuity tests with a multimeter to assure which piece is working properly and which is not would need the model number for your unit to provide schemat ... Dishwashers

Whirlpool Quiet II (DU110XTPB1)... Two problems (maybe it's one)... Start/resume light flashing and won't stop. I have tried on the different button combinations from this website and other websites and none of them seem to make a difference. The flashing continues. That's problem number one. Problem number two is that it seems to go into some sort of washing cycle in completely random intervals. When it's in one of the random washing cycles the following lights are on; Normal Soak and scour


Hope it's under warranty, maybe logic board, poor motor design causes main PCB failure ... Dishwashers

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

After interrupting a wash cycle by opening the door, the "start" button indicator will not light when the start button is depressed. (Neither will the "delayed start" indicator work.) The dishwasher will not resume any operation. All other control indicators light when selected. Removing and restoring power to the unit does not clear the problem. The unit is a Jenn-Air model JDB1100AWB.


It is possible that by opening the door mid cycle, the door switch mechanism has got disengaged. Refer item 11 in ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

JennAir JDB1080AWS I have a jenn air jdb1080aws and the light console has gone out. The lights are very dim and you cannot change the cycle. If you press one button a different one lights up and very faintly. Also the timer does not light up anymore. If I replace the panel-con Part Number: AP4364294 would this fix the problem. Thanks


... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

I have a F&P dishwasher model DW60CDX1 (around 5 years old) which we cannot start a cycle. The dishwasher turns on (power button and all programme indicators light up) but when you press a programme button nothing happens - the lights don't change. We have switched the power off at the powerpoint and on again a few times but this has not rectified the problem. It was playing up before this in that sometimes the programme would not start when a button was pressed but I just closed the door mor


The micro switch in the door which senses the door closing has probably failled. This is accessible once the inner door cover is removed. Switch should be under $10 from electrical store. Or buy through appliance manufacturer. ... Fisher and Paykel Dishwashers

I have a whirlpool model KuDSO1FL and the clean light blinks and won't start after the cycle has been selected and the start button is pressed. I have tried canceling the cycle but it won't work. The dishwasher was working yesterday and today it drained once we cancelled the cycle and then pressed start but that is all that we could get done. I don't know what the problem is.


Your appliance's clean light blinking will require a service call. It could be several things indicating a problem that are not serviceable by the home owner. You can try turning the power off at the breaker box, then turn it back on and see if this ... Dishwashers

Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

We have a 2003 KitchenAid KUDI01IL Dishwasher that will not start . We had problems with the top rack dishes getting clean and we replaced the chopper. The dishwasher worked fine for one cycle, but now will not start. The buttons have lights except for the high temp scrub light. The dishwasher will drain when cancel is hit but that is it.


... KitchenAid 24 in. KUDI01IL - Multiple Color Free-Standing Dishwasher

Hi, I have a Tecnik TKD/795 dishwasher (not sure which version - its the one with the three black rubber buttons on top). The problem is that the 'ready' button's led light is continuously on green 'on' so I can't change the program select. Also when I close the door to automatically start the cycle - nothing happens ! Please can you help ? Thanks Mr. Arwel Jones


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. This issue can be either due to a\015\012faulty door latch or door lock switch which is not engaging itself. An ... Tecnik 24 in. TKD795/3 Built-in Dishwasher

We have a KitchenAid dishwasher (KUDI01FLSS6) which has not been working properly for a long time. We have the dreaded green blinking light mystery. We understand that this could indicate several different problems. We have found that if we run the sink water until it is hot, then start the dishwasher, and then after ten minutes we open then shut the door, it will consistently run the full cycle perfectly. Does this give you any hint of what might be the problem component -sensor, element, the


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

We have had three electrical problems in the past 6 months. This one has the "Clean" indicator repeatedly light flashing in a pattern of 6 flashes and then one flash. The dishwasher will not start any cycle, so is out of commission. I am ready to throw this thiing out! Unit is about 3 years old. Model: 665-13422K701


Hi,Most if these models were made by Whirlpool and the flashing clean light is a common error code for them.If the clean light is the one flashing then your dishwasher could have a heater circuit problem (depending on the age) or this cou ... Kenmore Dishwashers

Hi, I have had a few issues with my ST663 machine. The current problem: the rinse cycle light keeps flashing and it doesn't start when you shut the door. I have tried holding down the right button but it beeps twice and nothing happens? Also tried holding both buttons down for a while and still no success. I got a new electrical board installed not that long ago so not very happy hoping it not a big issue. Do you have any other things that I could maybe do?


HiIf you have already tried to reset the unit by pressing the High Temp wash-heated dry button for 3-4 times in sequence then the problem is either with the door switch or the keypad itself that has gone bad and should be replaced. Hope t ... Dishwashers

I have an indesit dvg 622 kix dishwasher and about 30 seconds after starting a programme the 1st indicator light starts flashing and the machine sounds like it is going through a emptying cycle what could the problem be


... Indesit Dishwashers

I have a Blanco BIDW60 dishwasher and when I depress the ON/OFF button to start it before choosing the cycle, only the top pilot light comes on, instead of both. I noticed one of the springs has fallen off the bottom of the door. Could this affect it?


... GE Nautilus 24" Built-in Dishwasher

Kenmore 74362 My model# is 665.74362400 this unit is only just over one year old. My problem is it shut down and the quick rinse light started blinking. I have tried some of the button-reset procedures that were on some other responses but to no avell I even left it unplugged for a while. Any impute would be appreciated. I have a Kenmore Dishwasher Model #74362. After we run a cycle for a normal wash and heated dry the dishes are all very dirty and greasy. It is as if they were never washed. Th


I had the same issue and you will never beleive the solution.\015\012Steps to follow:\015\0121) run one full cycle with no dishes or soap\015\0122) run one full cycle with a dishwasher cleaner like Jetdry\015\0123) run one ful ... Dishwashers

Whirlpool APD5550 Dishwasher, cycle does not start, green light on start button flashes 6 times, pauses, flashes 6 times etc. can you please give me some indication what the problem may be. Thanks


... Dishwashers

My Amana dishwasher will not start anymore. The selection panel lights stopped turning on a few months ago, but we could still push the start button to start the cycle. Now that won't even work. Obviously an electrical panel problem, but what can I do to fix it?


... Amana 24 in. DWA22A Built-in Dishwasher

I have a SMEG dishwasher. Can't find the model number on dishwasher or manual. Had two flashing lights and referred to manual - indicates a blocked filter. Cleaned that out, but now when I try to put it on "light" cycle (indicated by wineglass symbol), that light flashes (but no others as would indicate a problem).. All the other cycles work fine. Any ideas? Thank you!


Hi.If only the crystal light is flashing and no other light is on, then that is not an error code. Problem can be a temporary malfunction, or a defective control module or keypad.The delicate (crystal) light flashing with last ... Smeg 24 in. STX2 Built-in Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

I have a whirlpool in counter dishwasher model # DU915PWPQ0 serial #FS2536586. The problem i have is the light cycle, green light is constantly blinking. When another button is pressed the heavy and normal cycle lights start blinking and the light cycle, light is illumanated constantly. I have left the power off for 24hrs and when turned on the light blinks again. it will not start any cycles.


Hi Mike...As I said..it flashes 4 times (not 5) 4 times then stops and starts flahung 4 times again. Also, the float is free moving in the tub,\015\012\015\012Any other suggstions??\015\012\015\012Thanks\015\012Dave ... Whirlpool 24 in. ADP5962 Free-standing Dishwasher

Hi experts, My Indesit IDL530 dishwasher never seems to run on any of the 5 programmes. On pressing the power button, the red light comes on and on pressing the start/reset button, the light signalling washing comes on and not the one showing water intake. But even then nothing progresses and just a buzz with that wasing indicator on shows for a second and goe off. But today only the buzzer sounds when pressing down the start/reset button and no indicator comes on atll. Will be great if you coul


... Indesit Dishwashers

Replaced control board on my Kenmore dishwaser 665.13122k703. Still have problem with blinking lights and maybe one minute of operation, then stops and normal wash light blinking again. Cancle drain button only one that works, then normal wash blinks. I have another control board, however before I install it, should I be looking eleswhere the the problem ?


... Dishwashers

Kenmore model 5871526 When wash cycle is selected and start button is pressed, the wash cycle indicator, heated dry indicator and the Washing cycle indicator lights flash continuously - but the dishwasher does not start


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1927 seconds