Having problems with your Dishwashers ?

Have hoover nextra megaload dishwasher but have not got the manual. How do I set the time delay without the machine starting? Thanks.

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have hoover nextra megaload dishwasher but have not got the manual. How do I set the time delay without the machine starting? Thanks.

... Dishwashers

Just got a used F&P Smart Drive 5.5 MW059. First few times I used it wouldn't always start on certain settings but once it did start it ran through just fine. On the fourth use, it was very difficult to get it to start and it just stopped after it filled up. Pausing and restarting, shutting of machine and retrying did not help. Was able to advance to rinse mode and got machine to drain water; however, instead of going into spin mode it just attempted to drain continously. I let it do its th

Did not realise this is a washing machine and not a dishwasher.\015\012\015\012Looks like some consultant has already been dealing with you on this problem.\015\012\015\012Hard to say if it is a simple as an inlet solenoid val ... Dishwashers

Can't set time delay.

Would your start button be stuck? check to see if there is something keeping it pressed in? if not your control star button could be shorted...let me know ... Kenmore 24 in. 16462 / 16464 / 16469 Built-in Dishwasher

Hi ive got a karcher k.3150 ive only had it 2 months and ive gone to use it the 3rd time and the detergent is not coming out of the container and ive done all checks-blockages etc and dont know why its not releasing the detergent?...the clear pipe is not sucking the detergent up when the machine is on and the lance is set to mix

This seems strange, as it is under warranty you can take it back or contact them about the situation. It depends were you purchased the machine but if it is a manufacturers fault they will fix/replace it. ... Karcher Pressure Washers

Hello. I was given a dishwasher, whirlpool ADP 755. I've had it about a year and finally got it plumbed in yesterday, so excited! Not having ever had a dishwasher before, i'm uncertain what to do and i cant find a manual online. I tried putting some cups in it and running it on all the different settings on the dial but each time the cups are still dirty. The machine is steamy so looks like hot water is passing through, but its clicking through all the programs very quickly and leaving stuff dir

... Dishwashers

Model IGV 659.1 Dishwasher When switched on the 'time display' takes longer than 2 minutes to display the planned wash duration. The display works fine to set a delayed start. After cycling the start delay round to 0, or after RESET (buttons A and C pressed) the unit is then 'nudged' into displaying a time. After, at last, a time is displayed the unit works fine.

... Kuppersbusch Dishwashers

ETNA ENF 18500A/5 type: 3.E1.181213221110 36 VLENNL 5 Dishwasher lights are on, and set for running, but the dishwasher does not do anything. Sometimes it makes a slight hum when closing the door, but most of the time, nothing. It stopped running after standard dish washing liquid was put into the machine by mistake. At that time, the machine started and ran through part of the cycle, but did not complete, and did not drain the water. Since then it has not started again. I have remo

... Dishwashers

My built in dishwasher ser no sm843049B-Model number GSD696ON1OSS will not reset. I mistakenly used the delay wash setting. It is set at 1 hr. I have used the start/reset button several times and the delay continues to show 1 hr. I don't see that the timer is moving in any way. It seems to be "stuck" at 1 hr . Is there a way of "erasing" the previous input? D Bafkas

Hi,\015\012\015\012Try to do a hard reset by unpluging all the cords for 1hour and then plug it back.\015\012\015\012Goodluck,\015\012Please don't forget to rate the solution ... Dishwashers

I have a delay button on my dishwasher that has 2, 4 and 8hr delays. I pretty much only use the 2hr setting, but the last time I set it for 2hrs it went to 4 by itself and now it won't go to anything but 4hr. Is there a reset button or something I can do? Thanks, Linda Heydt

... Kenmore Dishwashers

Carlton Cs1w. Hi I have a Carlton slimline dishwasher. No problem with filling, heating and emptying. But if I set it to full programme it sticks. Starting with pan setting and letting run right through programme it just keeps sticking. On last programme timer moves ok for first 10 or so minutes then gets no further. Tried different settings, checked everything I can think of and cleaned added salt etc. Got given. Last owner only used a few times, moved house and no room for it. But was sitting

... Dishwashers

I accidently hit the start button twice and, I guess, set the machine for a delayed start. How do I reset it so that I can start it now? And it's (just now) set to the pots and pans (which is fine) and hot dry (which I don't like) and won't let me change the settings

\001 To cancel the delay and start the cycle, press START/RESUME. ... Whirlpool 24 in. GU2500XTPS Stainless Steel Built-in Dishwasher

No pressure,but some times have hi pressure, but just for a few seconds. The person before me had the machine without been used for long time now has this problem. only had pressure for 2 times than nothing again help me please. Thank's Astro

First if you have a filter where the water is coming into machine and if you have not already cleaned the filter clean it,but i'm sure you have already thought of that after that the pump may have a problem, most of the time it is cheaper to buy ano ... Honda Karcher G2400HH-R Pressure Washer

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark

... Kenmore 24 in. 16934 Built-in Dishwasher

I have a kenmore elite dishwasher model # 665.1392 I had set it for a wash with th 4 hour delay and that shut off and now the complete blue button is flashing 4 times with a pause and then flashes 4 times again. If I open or shut it, it beeps 15 times. I tried doing the normal wash - heated dry back and forth trick but no luck with that. Any suggestions?

... Dishwashers


Hi Please check your oil zzle is not blocked at all. Remove the burner head and renew the nozzle. If that fails you will need to check the fuel pressure from your fuel punmp which should be at least 9-10 bar. ... Pressure Washers

We have a Whirlpool GU980 Series Dishwasher. All the lights work. No matter what setting I use, it fills up, and then nothing happens. The "washing" light will be turned on, but nothing happens. I try to drain the machine, it will make a sound like it's going to begin a process, then it just stops. Do these things just "die" after some time? This machine is 7 years old.

Sounds like something is caught in the pump impeller. you will need to take the pump apart inside the tub. ... Whirlpool GU2400XTP Built-in Dishwasher

It does not matter which cycle is chosen, once "start" is pushed on our Asko D3120W the drain pump comes on empties the machine, then it fills for the first time, and turns off. It happens on all cycles. We have turned off the power thinking that would re-set the machine, but it has not worked. Do we need service or is there something we can do at home?

Hello &\015\012Welcome to FixYa\015\012\015\012The problem\015\012seems to be with the frozen main pump or the pump seal/impeller gone bad. To\015\012solve this the pump and motor has to be removed and then the part rep ... Asko 24 in. D3120 Dishwasher

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW

... Dishwashers

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi

... Maytag Dishwashers

Have moved into a house with a Bompani Antilla BO 02014 model dishwasher. There is a control knob on the right hand side with settings and it seems like it controls the time the dishwasher is on (similar to top load washing machines). I do not know which settings to use or what they mean. Can you help? Thanks Terry

... Dishwashers

I have some problems with a Whirlpool DWF 406 dishwasher: The other day, my wife complained about it not finishing a program (just stopped and started bleeping). I saw a post at this forum where it said to clean out the black grid down my the sump. I did that, and then the dishwasher worked fine a couple of times. Today when I got home from work, the machine just bleeped at me and and the green LED light by the start button flashed 9 times over and over again. Does anyone know what those 9 flash

We have the same problem. The dishwasher is 10 years old. In one of the German forums they said that usually it's because the sieve ahead of the membrane has a fine layer of sludge and the pump cannot pump out the dirty waste water. They said that yo ... Whirlpool Dishwashers

Time delay how do i use the delay feature to make the machine come on afetr midnight?

1.Position the rotary switch to reset.\015\0122.Press the RH button, with the clockface on it, once for every hour of delay required. The display will change to 1H, 2H etc.\015\0123. reposition the rotary switch to the number of the requi ... Indesit 24 in. DE73 Evolution Free-standing Dishwasher

Bosch Dishwasher I have a Bosch Dishwasher that is a little over a year old. Loaded it up and ran it last night. Got up this morning to unload it, and load it again. Got it all set and went to start it but there is no power. The circut breaker looks fine. But no power to the machine. Not sure what is going on, or what needs to be done. Thanks....

... Bosch SHU3306UC Built-in Dishwasher

I have an Asko w66 front load washing machine that will only wash one way with a 60 second time delay and washes the same way again instead of reversing. At no time will it wash the other way. At the first spin cycle the water is pumped out but the wash drum will not spin. The pump continues to pump and will not stop while the one way wash continues. The timer stops at this point with the one way wash and pump still pumping continuously.

... Asko Dishwashers

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi

... Hobart 24 in. LXIH-3 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0812 seconds