Having problems with your Dishwashers ?

The manual is not very clear. Does the LED burning mean the heated dry is on or off?


Answers :

On

thanks
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The manual is not very clear. Does the LED burning mean the heated dry is on or off?


Onthanks ... Dishwashers

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

I have a built-in Kenmore UltraWash ~ Model 665.15819990. The problems we are experiencing is lately when we press "Normal Wash", the "Lock On" will flash on and off, and then "No Heat Dry" comes on & off and nothing works. We have tried pressing and holding the "No Heat Dry" button for 5 seconds and sometimes this clears everything. However, more recently, nothing is working. Suggestions?


... Dishwashers

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

I have Jenn-Air dishwasher that I use the heated dry cycle for. Last night at 11:00 pm or so I ran the unit. Today at 10:00am when I opened the door steam barrelled out and everything was so hot to the touch I gave myself a significant burn when grabbing a non-metal item in the dishwasher. Should I be concerned there is a problem with the entire unit or just the heated dry cycle? Should I be concerned about fire danger due to a short?


... Jenn-Air 24 in. JDB2100AW Dishwasher

PDW9280J10SS dishwasher has been in use for about 3 years. The control panel is not working properly. I use the up/down arrows and it turns on heated dry etc. When I push the heated dry button, it changes the lights to the different cycles (which is what the arrow keys used to do). The normal wash light won't come on, the only setting that seems to wash a full cylce is antibacterial. It seems like something burned out. What should I be looking at as a possible cause/fix. Unfortunately, I don't h


... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

Kenmore Ultra Wash Model 665.15801891 (Serial FJ3403697). This is in the USA. Unit will not run. Two lights are lit on the display panel and do not go off - 'Drying' and the #2 on 'Delay Hours'.rn I have turned off the power at the breaker box hoping it would reset. Once power is turned back on the Lock light comes on. I can clear that by pressing 'No Heat Dry' for 4 seconds but then the 2 lights mentioned above come on and do not go off. Any suggestions? Can you tell how old the unit is by t


Plase confirm if your model has the same front panel as the one shown in this manual.\015\012In that case try this sequence to reset the dis ... Kenmore 15899 Built-in Dishwasher

I have a FDBB2040FC3 dishwasher and the cycle doesn't complete anymore. I will start the cycle and after awhile the Hi-Temp LED and the No Heat Dry LED will start blinking and the unit stops. The dispenser does release the soap pack and the dishes seem clean but this doesn't seem normal. Thanks for your assistance Todd


Have you checked the element or the heater in you unit when the units senses that the unit is no longer heating the water the unit will stop and not progess any further into your cycle you can check this by doing a continuity test on the element to s ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a GE dishwasher model GLDL560N10SS. I noticed a burning smell coming from it the other day and then realized that although I can hear water running into the dishwasher when I start it, it never actually runs in the sense that the water is pushed through the various outlets to wash the dishes. I'm assuming that it is because the unit is dry and the heating element is still coming on that it is causing a burning smell. If I open the unit and reset it, it pumps the water back out into the si


The problem sounds like it is in the water inlet selonoid. Pull off the bottom panel and this is the part that the main water line hooks to there is a selonoid and it has a plugg inconnection to it unplugg it and check for power when the unit is supp ... Dishwashers

Even though I turned up the thermostat on my hot water heater, the water in the dishwasher does not seem to be hot enough. Mold is growing in the food grinder and even though I choose the heat dry option, the dishes are never dry. Yet, when I touched the element, I got burned. The dishes are not getting clean because it doesn't seem to be hot enough to cut the grease.


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

The standard procedure to start the machine is to select a cycle (normal, dry heat, etc) then press the start key. Currently when I select the cycle and the cycle LED is on, pressing the start key does not start the machine. I can press cancel, then start and then choose the cycle and it will work. Also, if I first press the start key, the machine will start and the previous wash cycle selection LED will light up and that cycle will run. Do I have a problem with the keypad or the con


... Kenmore 16632 Built-in Dishwasher

I have a whirlpool quiet partner i dishwasher (model DU1055XTSQ2) that has suddenly stopped working. Control panel has partial functionality. All of the buttons on the control panel have a green LED feedback light when depressed. None of them provide LED feedback anymore except the Hi-Temp Wash, Sani-Rinse, and Heated Dry buttons. So there is power to the dishwasher. Any ideas? Please help Scott


The control board has failed.CLICK HERE to see the parts breakdown. ... Whirlpool DU1055XTSQ Built-in Dishwasher

My dishwasher is leaving a residue on my dishes and not fully cleaning them. When I use the HEAT dry or SANI Heat, I smell a burning smell and not sure why this is. Solution?


Possible unit is not getting enough water into unit...this could be from a bad water inlet valve if the water is not high enough in unit the heater will get to hot as it is designed to heat the water to sanitize. try a new water valve and see if this ... Maytag 24 in. MDB5651A Built-in Dishwasher

Heating element The element is not heating up during the drying cycle, how do I tell if the element is burned out or a wire has come loose???


\012Remove the screws on the back of the unit and take off the back two panels.\012Facing the back, there is a thermostat toward the back-middle-right... it has a brass nut that holds it in pla ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

When I take a glass or cup out of the dish washer after they are cleaned and heat dried, or a day plus from the cabinet to put cold water,too many small bubles are floating on top the water surface, as a soap-like condition; it clears up shortly. The tech told me it is normal. I think it is not normal because I suspect the rinsing is not totally complete because of the water conservation design. Am I drinking soap-water?


Use a rinse agent., such as jet dry. the owners manual will provide you with the specific location as to where the rinse agent dispenser is locatedl ... Dishwashers

Dishwasher stop running with about a minute left to go, water still in the bottom. Following lights are blinking; high temp wash, sanitize, and no heat dry. I have check that the garbage disposal is clear, even ran it for a while. The over flow valve does move up and down. Pressing the buttons mentioned above does nothing.


I am assuming this problem has been fixed. If not then please post a comment to confirm which bit is still not resolved. ... Frigidaire Dishwashers

When dishwasher is set to begin, sensor takes very long period of time. Cycles are longer than minutes indicated. Dishwasher fills with water but does not wash. Water then drains as though cycle is complete and moves to next cycle. Then the process continues. When cycle for drying is reached, much heat is given and occasionally it smells as though there is burning. A 82 minute procedure turns into hours.


... Kenmore 24 in. 16532 - Multiple Color Built-in Dishwasher

My Frigidaire 24 in. FDB1050RE Built-in Dishwasher has a light on under the "heat dry" button. It will not start or clear...


I am having the same issue. This might be a common problem. ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Ran the dishwasher and the water didn't drain completely. Checked the drain line for clog - it was clear. Scooped out the remaining water (barely covered the flat wire mesh filter in bottonm of the machine) and cleaned off the canister mesh filter and carefully relocked the filtyer in place. Tried to run the machine last night. Soap tray opened but apparently no water cycled through the machine as all the soap was in the bottom of the machine. The heat never turned on to dry the dishes and


Hello Ramona Doug,\015\012 Try disconnecting power from your dishwasher for a few minutes to clear the memory and then reapply power again. Start a wash cycle without dishes on the hottest water setting and after a few minutes.. pause the wash ... Bosch Dishwashers

I have a Maytag dishwasher model MDBTT60AWW. None of its wash modes will work when pressing their respective buttons. The Fields Service Test functioned normally with the exception of the "heated dry" and "sanitize" LEDs not being lit. Tried to perform the Manual Function Test, but none of the components would operate upon pressing the respective keys for testing their operation.


Hi, \015\012Sounds like either the control board or the keypad.Try removing power from the unit to see if it will reset.\015\012Now try running the diagnostics…RIBBON CABLE CLEANING ... Maytag 24 in. MDBH955AW Built-in Dishwasher

Hole! The heating element burned a hole in the bottom of the tub causing it to flood my basement under the kitchen. It is 2 1/2 years old (out of warrantee) and Sears offered us a 10% discount to purchase a new one! I would never again pay money for a Kenmore product if that is how they stand behind the products. I intend to warn as many people as possible to stay clear!


... Frigidaire 24 in. GLD2150RCC Built-in Dishwasher

I have a model 665.17791790. It goes from wash to dry (the dial is 3/4 way through wash cycle) and the dishes appear rinsed, but then it gets stuck and the dishes continue to heat indefinitely. I have deformed plastic cups and started to burn to a darker color the dish rack coating. What is the problem do you think?


... Kenmore Dishwashers

We have recently fitted a Smeg dishwasher Mod D1612CA9 .We have used it half a dozen times and have a p resistant burning smell.It is fitted under a draining board of the sink. We noticed that in the pack there is a clear 3 inch wide strip should we of fitted this above the control panel, is this some sort of heat reflector ?


... Smeg Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0867 seconds