Having problems with your Dishwashers ?

My Whirlpool Duet, model WFW8400TWO2, powers up but then shuts off when I hit Start. There are no error codes displayed. I replaced the CCU and ohmed the door switches, the pressure switches, all okay. This failure happend about a year and a half ago but I wasn't around to see what was replaced under warranty. Any ideas?


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Whirlpool Duet, model WFW8400TWO2, powers up but then shuts off when I hit Start. There are no error codes displayed. I replaced the CCU and ohmed the door switches, the pressure switches, all okay. This failure happend about a year and a half ago but I wasn't around to see what was replaced under warranty. Any ideas?


... Dishwashers

Can't start the Honda GX160 5.5 HP Electric motor on my Chore Master 2400psi Pressure Washer. Got gas (checked through feed line), new spark plug, switch on, gas, choke ok, throttle a bit funky (about 12 years old on loan from a friend unused for 5+ years, no manuals). Recoil string sounds close to kicking over, but pretty half-heartedly ...


Is there an oil sensor unit if it is going bad it tells the engine the oil low and engine wont start. I had same problem with my pressure washer, i just unplugged the sensor unit and it started fine ever since ... Pressure Washers

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer

Plastic Pieces We purchased our ASKO 1385 dishwasher 7-8 years ago. Over the years, I have found "small square, thin, pieces of gray plastic" inside. Where are these coming from? Also, we have replaced the drain pump 2 years ago and looks like we'll be replaced the main pump within the next few days as no water is going through. We are looking at paying big $$$ for that pump. Almost half as much as purchasing a new dishwasher. Is this a common problem?


Yes, I have the same problem and it is the upper bearing rack, not the pump impeller. The new bearing kit is $30.00 (another is available for $123.00-the same!!). ... Asko 1385 Dishwasher

I have a Dewalt 3800 pressure washer fitted with a 67DX39G11 pump. Started unit up for the first this year, has pressure for 15 seconds then nothing. Water is flowing through okay, everything seems in order but no pressure. Unit is 2 years old but has only 15 hours of total running time. I think the pump has failed, is it normal for a pump to fail with only 15 hours on the clock?


... Dewalt 3800 PSI Pressure Washer

I have a Karcher 550M pressure washer and was using today when all of a sudden the water started to pour through the handle hence lost the pressure of the water. Is this a rubber washer issue or the gun needs replacing or simpler than that. To be honest although I have had the washer for about 3/4 years now It is hardly used. Also can I fix it and where would I purchase the allen key to replace. Thanks Brian


... Karcher Pressure Washer Gun 91120200 91120200

I have a mi-t-m pressure washer in the ca-series.The problem is the motor shuts down at times with out any reason. The first time I used it was on a house with a well supplied water. It worked fine,brought it home where I used it with no problem. It was used twice that first year. I then winterized it.The second year brought it out to the same house,I was using it for about a half hour when it just shut off with out any notice. I noticed there was back pressure in the engine when I tried to rest


Mi-t-m pressure washers have a Low Oil shutdown feature that turns off the motor, this is often causing similar problems on this kind of appliance.Have oil checked, if oil is fine , then the sensor that controls oil pressure and activate ... Pressure Washers

Kew hobby 1650 pressure washer pressure switch replacement


... Pressure Washers

I have a karcher 4.6 pressure washer that developed the usual fault.... drop in pressure and leaking from the cylinder head. I have replaced the cylinder head and the attached control chamber. The pressure is now good again and the leak is fixed. Unfortunately now when the trigger on the lance is released the the machine does not switch off automatically. I have bled the machine by letting water run through it


... Karcher Pressure Washers

Troy built pressure washer won't start. It has a Honda 160 CVG motor. I used it for about a year and then it stopped working. I've replaced fuel and spark plug. Spark plug is soaked every


... Karcher 2500 PSI Pressure Washer

I was given a low hour, 10 year old, CH PW205002LE 6.5 HP gas vertical shaft 2000 PSI/2.5 GPM pressure washer with a Lavor pump. It did not work - no pressure. I found a broken o-ring on the brass unloader valve and replaced it with a ring as close in size as I could find as the part break down doesn't state size. Everything was very clean. I coated everything with silicine grease and reassembled, seating the brass piston? as deep as it would go. I had to press the trigger in order to get the mo


My personal experience is that 40% of all the sellers I dealt with on e*** exaggerated their products or worse. If you decide to go the e*** way be sure you put it on a good credit card so you can get your money back if it's a bust. Don't use your ba ... Campbell Hausfeld Pressure Washers

A Kenmore dishwasher, model#66513743K603 will wash okay until it drains after cycle that dispenses detergent. Then it takes in half amount of water, wash motor short cycles & then drains.Next cycle works okay. Main control board was replaced but problem wasn,t solved. Rene


... Kenmore Dishwashers

Model: 1578201D PSI 4000 3.5 GPM The machine is only 2-3 years old and has always worked fantastically (with very limited usage). The inlet fitting got broken and we replaced it with a new inlet filter (part number 35169) and now it has low pressure. Is there something else we should check or replace?


Hi there,A "chattering" pressure washer pump can be caused by many things. You could have a bent or damaged inlet line, or the water supply might be too low. Fixing these is simple, but checking on the water supply is critical. Never let ... Pressure Washers

Karcher K2.36 Pressure Washer I've just fired up my Karcher for the first time since last year and the motor started running fine, I then switched on the tap to allow the water through and the motor cut out. Now it won't restart, any ideas? I'm wondering whether the water supply should have been on before I switched the motor on but it's too late now! Help!


The water must be switched on, and seen to be running freely from the nozzle for a few seconds before switching on the power - suggest you check the fuse in the plug, and then try the above. ... Karcher K2.26 Electric Power Washer

I have a Frigidaire dishwasher that I have had for a year and a half - 8 months ago it broke and leaked into my kitchen ruining my wood floor which had to be replaced. Shortly after that the top sprayer arm had to be replaced. It has now leaked again with a much more prominent leak and has ruined a portion of my floor again.


I would check to make sure that the top spray arm wasn't over tightened when it was installed. That spray arm threads onto a plastic supply tube which is easy to strip, which will cause it not to tighten properly and leak down the side of the dishwas ... Dishwashers

Hi. we have W'house 905 dishwasher. Have had the element replaced. It gets to half way thru cycle then cutes out. Cuts off all electricity in the house. Restart again gets to half way then cuts electricity trip switch. Is ther an answer? Tks.


\015\012Hi\015\012\015\012\015\012This is happening due to shorted wires or worn out wires connected to the element. It may also occur if you are not using the model specific part as replacement. Please get ... Dishwashers

6.5 honda on pressure washer have no spark.Cleaned flywheel Check on/off switch with multi meter and oil level switch GOOD It set for 1 year whats next


Check the coil is gapped properly. Is the plug wire attached to the coil. Is the coil working. ... Honda Pressure Washers

Karcher B402 pressure washer Motor runs as soon as power supply connected, on/off switch does not seem to make a difference and no pressure at outlet? Was working fine, stopped for half an hour, came back and wouldn't work. Thanks Bob


Bob I had this happen to my Karcher, the pressure seals have blown. $Au200 for service and replacement from karcher dealer. tyhey would not sell the parts for a DFY ... Pressure Washers

New honda pressure washer maybe had it 2 years and only has about 3 hours on it, I was using it yesterday and it started fine and after running for about 10 min it shut down like i turned the kill switch, it has oil and gas but seems to have lost compression. It is a Honda overhead cam GCV 160, pressure washer is a Troy Built model


... Pressure Washers

Hi got a baumatic dishwasher bkd62ss.1 model, it gets half way between the last cycle and cuts out and blows the circut board switch, can turn dial and wee bit and re switch circut board and away it goes again. what would be causing this problem. had dishwash for about 3-4 years? thanks


... Baumatic Dishwashers

I need a 7022-140a02 power switch for a McCullouh high pressure washer FH180B. Every were I have tried to order, I am told the part is not available anymore. This is a maintenance part in the McCullouh parts manual. I thought parts were available for 10 years, they are still selling this pressure washer;


I need a 7022-140a02 power switch for a McCullouh high pressure washer FH180B. ... McCulloch FH180A Electric Pressure Washer

EXCELL 2500 HAS VERY LITTLE PRESSURE WATER SUPPLY FILTER NOT CLOGGED AND CARB JUST REPLACED CANNOT LOCATE PRESSURE SWITCH TO INCREASE


... Pressure Washers

I have a Craftsman 2700 psi pressure washer with a Briggs and Stratton 850 engine (80 year anniversary special addition) . It is about 2 years old and used very little and will not start. I filled it with fresh fuel and checked the oil. I also replaced the spark plug and air filter. I checked the fuel line thinking it may not be getting fuel, but there is no obstruction from the tank to the end of the fuel line. I am out of TS options short of taking it to a service center.


Here is the long answer with everything we learned while using a power \015\012washer twice a day for years::\015\012It sounds like could be one of the problems listed below or a \015\012combination of those things.\015\012\015\0121 ... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

My Hotpoit FDL570g dishwasher (that is less than 2 years old) is tripping the circuit breaker originally during a wash and now when the unit is switched off and and door is closed. I thought it may be a door lock / microswitch problem and replaced the microswitch. The dishwasher was good for four seperate washes but now the problem has come back when crockery is loaded when the machine is switched off. I'm going to check for bare / rubbed leads but not expecting to find this with a dishwasher of


Hi,\015\012\015\012If your washer is tripping the breaker when it is switched off, this is often a sign that water has leaked - or is leaking - into the bottom of the washer under the washing compartment where there are lots of exposed el ... Hotpoint 24 in. FDW60 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0866 seconds