Having problems with your Dishwashers ?

Have gone through three pumps on dual drawer F & P dishwasher and am reluctant to pay for another service call out. Is it hard to replace the pumps myself?


Answers :

Please confirm why you have had to replace the pumps.
\015\012Do you get any fault codes on the display?
\015\012
\015\012By pumps I am assuming you are referring to the rotor in the centre of the drawer on which the wash arm is mounted.
\015\012
\015\012Does it look like this?
\015\012I am assuming you have dd603 model dishdrawer unit.
\015\012This part is very easy to replace. Refer page 21 in this manual and follow the instructions to replace and fit the filter plate. The rotor can be removed by twisting the centre ring and pulling the rotor out. There are no wires. Replace new rotor and put and twist the centre ring back into lock position.
\015\012
\015\012I would be more interested in finding why you have to replace the motor rotor. (the pump).
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have gone through three pumps on dual drawer F & P dishwasher and am reluctant to pay for another service call out. Is it hard to replace the pumps myself?


Please confirm why you have had to replace the pumps.\015\012Do you get any fault codes on the display?\015\012\015\012By pumps I am assuming you are referring to the rotor in the centre of the drawer on which the wash arm is mounte ... Dishwashers

My dishwasher will not turn on and the Start/Resume light will not stop blinking. Is there any thing you can suggest to fix this without my calling and paying for a service call? We have stopped, restarted and reset the unit as well as cleaned out the soap tray. We have also switched off the electric to the washer as well to no avail. Really cannot afford another service call again so please help us out. Thanks. Chris


Reset the control again. Then change out your heating element.\012\012That should fix it good.\012\012Have a great day! ... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

Frigidaire dishwasher Mod# GLD4050RHS overheats, melting plasic contents, and venting steam upon opening door hot enough to burn my face. Did so when new, numerous service calls eventually leading to part# 5304467317, 154642901, 154467702, 5304467317 154543602 replaced. Satisfactory service 13 months and now melted another load. Suggestions? Fear fire hazard.


... Frigidaire GLD4050RHS Builtin Dishwasher

Hi, I emailed sometime ago about my fisher @ paykel dishwasher not working. This will be the first time I've used your service and I'm just a little unsure how effective it will be. I guess I'm a just being sceptical but i really want it fixed without paying call out fees and the like. So how much do i have to pay. The top draw will not turn on. At the time the draw was hard to open so i went through the procedure to recalibrate the draw when i was holding down the buttons to get it into self t


Please confirm if you still have a problem with the dishwasher. It is unclear from the thread of your responses as the statements of the other expert will be visible only to the client. \015\012Also please confirm what you mean by "buttons stop ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Water is not flowing into the dishwasher and as a consequence it overheats. In the couple of weeks prior we noticed unusual noises and taking longer to complete washing. Also since about two weeks ago dishes have had white mineral deposits and film on glasses. I suspect that the water pump is not working. I cannot find the salesslip from sears to see when we purchased the machine but I sus pect it was about 6 years ago. We are debating wther to have a service call, possibly including replac


Hi,\012Here is a tip that will help you to find out why water will not come into thedishwasher... Dishwasher Trouble No Water entering Dishwasher ... Kenmore 24 in. 16262 Built-in Dishwasher

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

Water will not drain out of bottom of dishwasher.It will go through the whole cycle but will not drain. This is a Frigidaire model no.FDB510LCS3 Serial no.is:noth70219331.Pump hose was disconnected and drained completely,dishwasher was put through another cycle and still ended up with water puddled in the bottom!! Could this dishwasher be called a lemon??? Does the pump need replacing?? I have noticed on your website that many others are having the same problem.To me it appears that it may be sh


Check the input to the drain hose to make sure it is not blocked by something like a cherry pit.  That could cause the water to not drain fully. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Broken Piece The center piece that comes up during washing cracked and has come apart. Is this a replaceable part? I am reluctant to call a repair man to pay him to tell me I need a new machine!


... GE 24 in. GSD5930 Built-in Dishwasher

I just finished a service call for my 5312UC/UC12. The tecnician says he saw water leaking under neath the machine but hoses were secure and no visible crack to the motor housing, The machines pump works but very little water is actually put into the tub, hence no dishwashing. This technician says that this is a repair that most technicians avoid because it takes a long time and costs alot and violated some sort of warranty. He recommend replacement after only 7 years!


This leekage may come from thermostads water isolation ring, just under rezistance leads. There must be a ceramic holder to fix it to rezistance. İf it is broken, thermostad may go down, or rezistance leads isolation (lastic washer) may leak wat ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

I have model number KUD 101TJBL0. I have spent about 300.00 on repairs. It keeps blowing the thermal fuse. I have had it replaced sev. times. My repair man has given up on solving the problem. I did read on another website that you need to replace the wiring kit that comes with the fuse. Me service man never did that and when I asked him about it he said that is not the problem and would not replace it. So, before I just scrap my diswasher and but a new one I thought i would order another fuse k


Hi,This applies mainly to Kenmore Dishwashers with the model number\015\012665.15835791 but also to any Whirlpool or Kenmore dishwasher with an\015\012electronic display. There are several possible trouble makers on this\015\012dishwasher ... Dishwashers

Plastic Pieces We purchased our ASKO 1385 dishwasher 7-8 years ago. Over the years, I have found "small square, thin, pieces of gray plastic" inside. Where are these coming from? Also, we have replaced the drain pump 2 years ago and looks like we'll be replaced the main pump within the next few days as no water is going through. We are looking at paying big $$$ for that pump. Almost half as much as purchasing a new dishwasher. Is this a common problem?


Yes, I have the same problem and it is the upper bearing rack, not the pump impeller. The new bearing kit is $30.00 (another is available for $123.00-the same!!). ... Asko 1385 Dishwasher

No sanitizer Hi, I've got a 501HT that's acting up, it is not taking up any sanitizer, is it the pump or could the line be clogged? Also, I've noticed the detergent line has never been installed, isn't there a pump for that aswell and shouldn't that be operational. The previous owner never mentioned it? Lastly, I had a service guy out this spring to do some repairs and told me that one of the coils on the booster tank was shot and should be replaced. Should I replace all of the coils or just the


Hello\015\012If you have a 501HT you shouldn't need a sanitizer because the machine sanitizes using hot water. The final rinse temperature should reach 82 C to kill all germs. The chemical pump's element tubes may be worn out. This would preven ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

We have and older Jackson model 10 AB at church, used 10 to 20 times per year. The pump motor quit this summer and was replaced by a local appliance service company. About $700 job. Upon using it recently, the first time since the new pump was installed, the RINSE cycle seems very anemic, that is, low volume and low spin rate. The dishes were not completely rinsed. Temperature was correct, 185 degrees. The service person came back to look with no improvement and now the Heaters will not co


Sounds like a wiring problem but it is controled by a thermo to make sure you get to the proper tempt . so ck the connections and mke sure the thermo is good . . and the element is good . ..hope this helps mm . ... Jackson 10A Free-standing Dishwasher

Blown Motor DW is about 16 months old. Started making some real bad noise. Lasted about a minute and then had a death howl. Called in repair tech who says motor is blown. $399 for repair which includes $125 for the part. I've rebuilt car engines, so can probably replace a DW motor. Any insight on how to replace the motor? is it worth paying 275$ for labor? Just bugs the hell out of me paying $400 bucks for a repair when i can get a new one for $450.


I haven't changed that particular brand of dishwasher motor, so I cant give a step by step, sorry. I do know the other brands it is optional to get the motor alone or the motor with the pump assembly attached, so you may want to ask abo ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

On 2/18/09, I had a part replaced (due to a recent recall issue) on our Bosch dishwasher, SHU43C06UC. I had not had any problems with my dishwasher - ever - and, since the replacement, my dishes are not being properly cleaned. The Sears repairman who replaced the part tells me that the part he replaced has nothing to do with my present issue and, because my DW is no longer under warranty, I would have to pay for any further services he may provide. 1) What do I need to do to troubleshoot this di


Http://www.boschappliances.com/safetyrecall/dishwasher/default.aspx?pid=BCH0905OIQ001 ... Bosch 24 in. SHU43 Built-in Dishwasher

I HAVE A GE DISHWASER MODEL#GSD2200G02WW I WANT TO CHANGE THE PUMP BUT CAN'T FIND A REPAIR MANUAL I CALLED A REPAIRMAN AND THEY WANT $300 TO CHANGE THE PUMP CAN ANYONE TELL ME WHERE TO GET A REPAIR MANUAL OR TELL ME HOW TO CHANGE THE PUMP IT DOESN'T LOOK THAT HARD PAUL


... GE Dishwashers

Bosch Dishwasher has started acting upo. If I turn on the dishwasher it runs the pump for approx 2 seconds then cuts out. This carries on the cycle spraying the soapy suds around the compartment but there is no running pump sound. Any idea how I can access the pump to either attempt to clean it out or to replace it? Or does this indicate another fault that may need attention. Any idea of the cost of parts UK. Thanks for assistance ****


Most dishwashers pump out briefly before filling in order to clear pressure chamber. The next step is the water fill which is monitored by the pressure/level switch. Once water level is attained timer will advance through cold rinse cycle. If no fill ... Dishwashers

Asko d3100 I have an asko d3100 dishwasher. Its just out of warranty and now the cup saucer light flashes and the water pump is continuing to pump even though there is no water. The dish washer wont start. What is the problem. I think the flashing cup saucer light is reporting a fault. If I know what the fault is for example faulty relay or pump then I can replace it. Can you help me with this one? Is there a service manual I prbably can get my hands on.


Remove the lower panel at the back of the machine. If there is water on the bottom pan, wipe it up with a towel or so, and the machine schould be like new again ;-)\015\012\015\012Good luck ... Dishwashers

G851 SC Plus started to trip GFI plug. Called Miele and they said there was nothing wrong with the dishwasher and the GFI was faulty. Unplugged from GFI and plugged into regular plug and it worked for a few days. Eventually stopped running. How wrong Miele was, it had everything to do with the dishwasher and not the GFI. It was only warning me a problem was coming. Appliance man came out, noticed water in bottom pan and order new pump, said seal probably gone. Came back, replaced the pump, put d


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

We have an AM-14 dishwasher. It now will not work on auto. It would sometimes and then not and now only on manual. We have had a couple people in to look at it. One says the main board was bad, so it was replaced and the problem continues. The board that was removed was put into another washer and it worked ok. We were told then that that a wire from the motor was wrong and thats when we called in another person. That person said the board was bad and they couldn't work on it. We are in Lancaste


... Hobart AM14-253 Free-standing Dishwasher

So I found this power washer for sale. The seller claims that the washer generates a good stream of water, not just full power. He also mentions that after a few minutes the engine starts to bog down like it is working extra hard. Does this sound like a pump issue? Could something be clogged or would the pump need to be replaced? Or should I avoid this power washer?


Don't buy a power that doesn't work.There are many expensive parts on a power washer. If it was cheap and simple to fix, the seller would fix it and the washer would not be for sale.Would you buy a car that doesn't work? Especially ... Pressure Washers

Kitchenaid KUD124SE DISHWASER SUDDENLY STARTED MAKE A GRINDING NOISE DURING LAST DRY CYCLE. TRIED RINSE AND ALL I GOT WAS GRINDING NOISE. BELIEVE IT TO BE PUMP. NEVER WORKED ON ONE. FIRST ALL IS IT MOST LIKELY THE PUMP AND IF SO HOW HARD TO REPLACE? tOM


You most likely have either a piece of broken glass or hard food debris in the pump. There is a cutter within the pump designed to grind food debris and flush it away. However, you can take off the lower wash arm, remove the (recessed) s ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1076 seconds