Having problems with your Dishwashers ?

Problem I think started with pump making noise,now no power to front control panel everything is dead regards


Answers :

Hi
\015\012\015\012

The\015\012issue seems to be with clogged/blocked drain pump assembly. First, check the\015\012drain hose for any visible clogging, remove if present. If it's still not\015\012visible then the drain filter or drain pump is clogged and you'll need to clean\015\012the drain filter and drain pump. To clean the units completely take the lower\015\012access panel out and clean the drain pump assembly completely. Also, check for\015\012any food pieces stuck near the pump impeller as something stuck inside the\015\012impeller could have been making that noise. Hope\015\012this helps...please post back for further assistance.
\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Problem I think started with pump making noise,now no power to front control panel everything is dead regards


Hi\015\012\015\012The\015\012issue seems to be with clogged/blocked drain pump assembly. First, check the\015\012drain hose for any visible clogging, remove if present. If it's still not\015\012visible then the drain filter or ... Dishwashers

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

SMU50e32SK dishwasher showing E06 in display after a few seconds. Dishwasher has one Main Power PCB and one control unit PCB in the front. Info: Main PSU PCB has been shifted due to overvoltage. All sensor checked, seems to be ok after this has been shifted. I don't think the induction motor(big pump) has been affected due to the relays in front. Could it be the Control PCB in the front or maybe the small drain PUMP. Well some of you properly now what E06 is referring to on this model.


... Bosch Dishwashers

SMU50e32SK dishwasher showing E06 in display after a few seconds. Dishwasher has one Main Power PCB and one control unit PCB in the front. Info: Main PSU PCB has been shifted due to overvoltage. All sensor checked, seems to be ok after this has been shifted. I don't think the induction motor(big pump) has been affected due to the relays in front. Could it be the Control PCB in the front or maybe the small drain PUMP. Well some of you properly now what E06 is referring to on this model.


... Bosch 24 in. SMU40 Built-in Dishwasher

I have a Whirlpool Gold Quietwash Plus (part # 9744480), due to a number of opening and closings of the door, the lights on the front panel now just blink. How can I reset the control panel.. I have tried power scour>air dry>power scour>air dry and only end up with both blinking instead of going into control diagnostics by pushing pots&pans. The unit will attempt to start then just go to blinking lights.. Thanks


I would cut the power to it for awile 5mi and try it that may do it ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a KitchenAid dishwasher model KUDC10IXWH1 that has no control power. I have already verified that there is 120V at the control board. The unit kept the lights on after the cleaning cycle was done and I couldn't shut them off. I reset the electrical breaker and now nothing works, but the board has power. Please give any advice you might have. I was thinking of replacing the board, but I'm not sure if it is the board or the front control panel. Any way to tell?


... KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH

I have a GE dishwasher with front control panel and at first the wash and dry lights stayed on and it was beeping every 30 sec. when I turned the breaker off for the required 30 sec. the lights started flashing and it is still beeping. The control panel seems to be frozen as it is not working and wont do anything.. everything was working fine before this. I bought it at Home Depot on 3/14/07 and had it installed by a licened electricion. Help


Call ge @ 800-386-1215 for service ... Dishwashers

My LG 24 in LDS 5811 ww quite working in the middle of a cycle. I have power to the machine, but no lights come on, nothing works. I turned off the power and removed the front pannel. The large brown wire and large orange wire that are plugged into the back of the control panel start to smoke. So does the large black wire and the large white wire. Any ideas, is this the heater or is the panel bad?


The unit will need a new Wire harness, Pump/motor assy, Main Pcb and inner door liner.\015\012Contact LG @ 1800 243-0000 they may help you out. ... LG 24 in. LDS 5811 Built-in Dishwasher

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

When pressing any front button on the control panel nothing will light up or start up in any manner,does look like it did not finish draining,have water sitting in the bottom. Pulled off front access panels no signof burned wires or anything becoming disconnected? do have small childern in the house pressing buttons? power is good going to unit.??


1)check any fuse blown in board.\015\0122)check supply to the board. ... Kenmore Dishwashers

Hi My dishwasher seems to get stuck in a cycle when you start it - it lets water in for around 20 secs - then pumps it out - then lets water in for say 20 secs then pumps it out - over and over and over... Model - says electronic on the front, has a rotary selector switch and a power switch on the panel along with three indicator lights. SGS43EO2ZA/16 Type S1501B Can you advise? Gerard


Hello Gerard,\015\012\015\012This is an overfill 'fault' generally caused by one of the following:\015\012\015\0121. Faulty or incorrectly installed flow-meter\015\0122. An airlock in the fill chamber ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Thermal fuse Dishwasher konked out mid-cycle and now no power to control pad. We've already had the thermal fuse replaced once (machine is only 2 years old!) and this appears to be the same issue. I tried to open the front and I think I can see where it is but not sure how to get it out and replace it AGAIN. I wasn't able to get the inside panel completely apart from the front of the unit so I was somewhat limited. I'd rather save the service charge if I can and there's n


Http://www.partselect.com/MultiModels.aspx?ModelNum=KUDS35FXSS&SearchTerm=fuse&RefineSearch=0Maybe this link will help ... KitchenAid KUDS35FXSS Dishwasher

LE on display panel. I have taken front panel off and all wiring has already been electrically taped together, so I don't think it is wiring. (This was done by a service rep when I had 1E problem) How do I tell if the impeller, rotor or blade is blocked? Or sump assembly or main power control board needs to be replaced?


Http://www.justanswer.com/questions/2bijk-i-have-a-lg-ldf6810st-dishwasher-with-an-error-that-the-serv ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I think I need to check the water pump/motor on my Bosch SHU43C dishwasher. It seems the water enters at the start of the wash cycle but then there is silence through the remainder of the cycles. Water will not spray. The drain appears to work ok to drain most of the water out. I have the washer out and upside down. Any hints on removing the base to get access to the pump? Should AI be looking at the control panel also for a fault? (the cycles seem to count down ok)


Click below;\015\012Latest Bosch Dishwasher Use and Care Manual\015\012\011\011\011\011May 4th, 2008 by Samurai Applian ... Bosch Dishwashers

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

The lights on the control panel do not come on so the dishwasher won't start. We have checked the electric box and it is getting power. What do you think it is?


... GE 24 in. Profile PDW9200J Built-in Dishwasher

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.\015\012So remove the panel and disconnect the wires, check all lead ... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Dishwasher leaking Our dishwasher all of a sudden started leaking. I've taken the front panel off the door and can see exactly where. It's not a hole or anything...it's at the front, left edge of the basin, the bottom left corner at the front. It seems that right after it fills with water, it starts to leak once water is moving around inside and washing cycle starts. It is as if big waves are being pushed to the front left corner and over the lip of the basin. I don't think the water level is to


Just an idea...if i'm understanding you correctly,could the door seal be creased there or folded over by use and age to permit this to happen? cause you said nothing is missing ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Leak from a De Dietrich Integrated Dishwasher has caused 3 red lights on the left of the Control Panel to flash and also a Blue Light on the right hand side of the Control Panel to flash. On resetting the Appliance Controls, the machine starts pumping out and then closes down, with the Control Panel lights flashing again. Help


Pull the built in unit out and tilt towards the rear right leg and the water will drain on to the floor. The Dishwasher then restarts but the anti flood sensor will reactivate after 2-3 more washes. Do not know final fix yet. ... De Dietrich Dishwashers

I have a mdd8000aws dishwasher. After a power outage (2 days) the power came back on, and the bottom drawer no longer works. It still make the chiming noise when the drawer is opened, but the control panel is not fully lit up and the washer will not start in any mode. The lights seem to flicker for a short moment and then they all stay very lightly lit up. Is this just a bad control panel or is there some other circuit that needs replaced? BTW, the top drawer works perfectly.


... Maytag MDD8000AWS Builtin Dishwasher

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hi I have a maytag quiet series 300 with model # MDBTT60AWW and it will not start. All the lights lite up but it will not start. I recently just had to replace an element due to a recall so when he was hear fixing the element I asked him what he thinks could be the problem and he said it sounds like it possibly needs a new control panel. Does this sound right and if so do you know where I can get a control panel. Thanks for your help


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1321 seconds