Having problems with your Dishwashers ?

My 7 year old kenmore Elitebuiltin dishwasher,model#66517059401 is not running water into the machine?


Answers :

Hello, welcome to FixYa.

I understand by reading your post (which indicates it is a Kenmore dishwasher) you appear to have a water filling concern, however if you could verify the machine is not getting water but maybe just not circulating...after it fills you should see water just below the element.

I would be much better equipped to help without generalizing. Initialy based on your post, it could be a fill valve, or the float stuck in the overfill position.

I'll watch for your reply and try and help going forward. Thank you.
Regards,
Macmarkus :)
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My 7 year old kenmore Elitebuiltin dishwasher,model#66517059401 is not running water into the machine?


Hello, welcome to FixYa. I understand by reading your post (which indicates it is a Kenmore dishwasher) you appear to have a water filling concern, however if you could verify the machine is not getting water but maybe ... Dishwashers

Kenmore model #363.14672100, approx. 10 years old. After the wash cycle, sometimes not all the water drains. This doesn't happen all the time but when it does, the next time I run the dishwasher, water runs out under the door. We have hard water and am guessing there is some build up. How can we correct???


... Kenmore 24 in. 15079 Built-in Dishwasher

I have a Bosch SGS43A22 Dishwasher approx 8 years old. When I start a cycle it fills, runs for about 15 minutes, then drops out about a litre of water from the bottom of the door, then completes the cycle without any more leaking. I have run the machine with the front panel off and can see that water bypasses the top of the seal and fills the well of the seal then pours out. It only happens the once. The seal is fitted correctly. Any solutions?


After 8 years service the seal may have perished, so you should feel for a crack by stretching the rubber where you noticed the leak. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

My 13 year old Maytag washing machine has been running fine. Tonight, I loaded the machine, it filled with water, but now will not run.


The most common problem to check is the lid switch. Depending on the model you may have a safety switch also and a fuse. If the fuse is bad the safety is prob. bad. Please rate my response. If you have more questions please include model #. ... Dishwashers

I have a bosch dishwasher SGS4332GB/29, 10 years old ,problem is no water in machine? pump running and water ok to machine?


... Dishwashers

Miele Dishwasher Model G1040, Type HG03, NR: 32/65143704 The machine is three years old. The cycle reaches almost to the end, then all three LEDs merge together, and the pump runs continuously, even with the master switch off. I have taken the machine out and removed the base plate. When I first took the machine out of its position, I tipped it backwards and water came out of the bottom. All hoses and parts in the bottom section seem perfect in every way but the inside of the bottom plate indica


... Dishwashers

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

We have a +11 year old Bosch SHU3006/UC/U06 that never leaves the wash cycle. We had to stop it during our last test run at 3 hours. Chat advise is suggesting a water temperature problem (I origionall thought the timer), suggesting that the cycle will not advance until it hits a set temperature (170 degrees). We checked and noticed that the water in the machine was only around 90 degrees during a wash cycle. We do not have exploded views or parts drawings, nor electrical schematics. I wou


Check continuity of the heating element to see if it is broken/open.\015\012\015\012The dishwasher prefers that the incoming water (water heater) be 120 degrees (F) ... Bosch SHU3036UC Dishwasher

GE Nautilus My dishwasher is approx. 6 years old. It has recently started having this problem. On the second cycle (the one where the little door inside opens and release the soap) does not want to work right. The door will open, but it is like there is no water spraying to spread it out. The soap (I've tried both liquid and powder) sticks and drys, running down the door and in the bottom of the tray. I have to open the machine and add the soap to the bottom of the machine if I want to get my di


Smoking from GE (Model:gsd3725f00bb) dishwasherWe moved in an old house, the dishwasher had been installed. but today we found smoking from the dishwasher and smells burned plastic. Could you have any resolution for me? or this problem is popul ... GE Nautilus 24" Built-in Dishwasher

I have a three-year-old Sears Kenmore Elite dishwasher. I find that despite the fact that we scrape and rinse our dishes before loading the machine, after each three months of use (two loads a day) or so, I have to take the machine apart (spray tower, racks, bottom impeller, bottom screen housing, food grinder cover) and clean-out the food grinder area, for it fills-up with sludge. The sludge restricts the water flow and there isn't enough flow to turn the impellers via that steering jets.


Have you tried different detergents? Some detergents after getting wet and going through the wash cycle with the debris from the wash turns into a grease substance that grimes up in some dishwashers. Try running the machine with hot water this someti ... Dishwashers

Glasses int he top rack of my kitchenaid dishwasher don;t get clean. they finish the run spotted and covered in what looks like baked on dirty dishwater. dishes in the lower rack look ok, but the silverware is always dirty, too. i figure it's one of two things - either the top sprayer isn't working, or the machines doesn't drain the dirty water well enough. or maybe it's something else - cycle regulator? the machine is about 4 years old. thanks


If you have hard water, glasses can look spotted and cloudy even after cleaning. Sometimes changing the dishwasher detergent can help. The easiest solution to clearing up glasses that start to look cloudy is to add some vinegar to the bo ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

No water The dishwasher will run through the full cycle but no water is coming into the machine. It is less than a year old and had been working fine until Christmas Day.


Don't try running the machine without water, as I suspect you can burn out the pump. Our machine wasn't getting enough water, so we removed the water intake valve and cleaned out a bit of grit that came thro the water line. If you are hooked up to ... Dishwashers

We have Kenmore that is 7 years old. It is one of these models : 665.11072912; 665.11072913; 665.11072914: 665.11072922; 665.11072929. The dishwasher is making a very very loud sound, taking very long to run and is not cleaing dishes. Water is coming out and draining. Water is very hot. Could the filter be blocked and if so how do we access it to take a look and clean it out Candace


... Kenmore Dishwashers

Maytag Model No WU202 is running through all cycles but is not pumping out the water from the tub. I can hear the pump running and a gurgling sound. Could it be the micro mesh filter that is plugged? Any detailed drawings available of the lower wash assembly and instructions to take it appart? This machine is more than twenty years old.


Hi,It sounds like your belt broke. Open the bottom access panel below your door and check. The part is :-http://www.repairclinic.com/SSPartDetail.aspx?PartID=2814&PPStack=1If you take off the front ... Maytag Dishwashers

GE GSD6610GOOB not cycling properly. Our dishwasher is about 6 years old and has been nothing but trouble the past year or so. We've already paid too much money repairing it the first time, (it simply stopped working - the control panel was totally dead) and don't want to pay anymore. Current problem - the machine starts up and fills with water and it sounds like it's running OK, then it will just stop, sometimes for a couple of minutes sometimes longer. Then it will start up again - and


... GE 24 in. GSD6600G Built-In Dishwasher

Kenmore model#587(Frigidaire) leaks under door. New install. Had machine for a year plus before install. took off front panel- can see water squirting past lower door gasket as wash arms rotate. cause is water running down door during wash cycle piles up in the channels molded into the lower left & right side of the wash tub and pushes out the sides of the lower gasket. looks like a design issue- called SEARS, they just want to sell me a new gasket! go figure. any ideas on a fix?


It does sound like an inner door seal ,however If you get upset at Sears and complain they may help you as they say the squeaky hinge gets the oil..And with Sears the more you squeak the better your chances of results ...Good Luck ... Dishwashers

4 year old Bosch SRS43C12GB/14 dishwasher running a full cycle but not heating water


... Dishwashers

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

I have a Kenmore Quietguard Standard model 587 Dishwasher. It's about 3 years old. Lately, it has been running fine through the first hour and then towards the end, it will pause and the "Hi Temp" and "Heat Dry" like will start blinking at the same time. It's like it is stalled. When this happens, I open up the door and look at the bottom of the dishwasher were the screen is, and I see there is standing water. I press the "Start/Cancel" button to help it drain all the way, which it does, but th


Hi,My take on that would be a bad heating element....the dishwasher is looking for the heat from it and that never happens....so it goes no further and gives the alarm....I would get someone to check that heating element out and replace i ... Kenmore Dishwashers

I have an kenmore elite "ultra wash" model 665. not sure the rest.. about 7/8 years old, making loud buzzing sound during wash cycles,starts about 5 minutes into the normal wash cycle. i removed the inlet protector and the chopper area and all was clear.clean...it's running now and seems to be pumping the water, but can live with this buzzing noise,,, any idea, is the pump on it's way out ? just stopped as it kicked into another cycle, at 42 minutes...but it will be back, any ideas ? (back alrea


Buzzing sound may be coming from a solenoid that is mounted under the dishwasher, below the tub ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My dishwasher is not cleaning dishes - it is running through its cycles, but when it is done, there is a heavy residue of soap and hard water and the dishes looks worse than when i put them in.I've changed dishwashing liquids and even replaced the extra cleaning solution (little hanging basket) with a new one, and still not washing dishes clean. this is a kenmore and is about 5 years old.


Hello there:There are 6 areas that could cause this to happen Please follow these simple steps okInvestigate each of these six areas if your dishwasher is not completely cleaning your dishes:\015\012\015\012 \015\012\015\012\015\01 ... Kenmore 15899 Built-in Dishwasher

My dishwasher is working well but makes an intermittent whistling noise, 10 seconds 'on', 10 seconds 'off'. The machine is 2 years old and runs on water from a softening unit (less than 0.7 moles/litre). None of the manual's suggestions has worked. How can I stop this noise? Thanks, Jim.


This is caused by a partially blocked valve or inlet, it is a little blocked, and this sound you hear is the air pushed through it making a sound. You need to clean out the inlet valves. \012\012\012 ... AEG 24 in. Favorit 80860iW Built-in Dishwasher

Cutlery is cloudy and dirty, some food is dried onto knives and forks. Cups and glasses are cloudy and not clean on inside. Coffee or tea stains are not removed. Plates and soup bowls seem OK , and water is draining properly. We have tried with less soap, more soap, gels, tablets and powders but to no avail. The dishwasher does not clean dishes etc, as as it once did. There doesn't appear to be any problem with the 'cycle'. The machine is about nine or ten years old, and has run fine until ve


Don't know much about Dishwashers but have you tried a descaler.Is the water spraying out as normal.Is the water actually getting hot, could be a heater element problem.If you look here you may get some other ideas just by loo ... Dishwashers

Cutlery is cloudy and dirty, some food is dried onto knives and forks. Cups and glasses are cloudy and not clean on inside. Coffee or tea stains are not removed. Plates and soup bowls seem OK , and water is draining properly. We have tried with less soap, more soap, gels, tablets and powders but to no avail. The dishwasher does not clean dishes etc, as as it once did. There doesn't appear to be any problem with the 'cycle'. The machine is about nine or ten years old, and has run fine until ve


They must have changed the way they treat the water in your area. those spots are caused by hard water. www.dishwasherfilter.com has a product out for this problem. it filt ... Bosch Evolution 300 SHE43M05UC Stainless Steel Built-in Dishwasher

I have a Maytag dishwasher quiet series 300. It is one year old. The problem I am having is this. After running a cleaning cycle, there is water in the bottom of the machine. If I push the start button, then cancel a few seconds later it will drain. Any idea? Thanks, Terry Roose


Hi Terry, Welcome to FixYa, I am Kelly. \015\012 A few things can cause this. Most of the time it is drain related with the Air-Gap being the culprit that is restricting drain flow. If the dishwasher drain has a restriction ... Maytag Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1779 seconds