Having problems with your Dishwashers ?

Zanussi ZDF 511 S dishwasher not draining. Shows error message '20'. Cleared filter, removed hose from usual drain and restarted cycle. Still not working - same error message. Any suggestions would be helpful. Thank you. Myles


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Zanussi ZDF 511 S dishwasher not draining. Shows error message '20'. Cleared filter, removed hose from usual drain and restarted cycle. Still not working - same error message. Any suggestions would be helpful. Thank you. Myles


... Dishwashers

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

I have had an E24 error message on my Siemens freestanding dishwasher. As well as the Error message the the little tap sign lights up too. Up until now the problem has occurred around 1 in 3 attempts and mainly at night but not in the day. When it does work the washer works perfectly and washes well. Today it will not work at all. The error always comes up 2 minutes into any cycle. I've tried turning the water feed off and on and in the past this has worked. It sounds like no water is gettin


Hi Steve\015\012\015\012E24 error normally indicates failure to drain, the first\015\012thing to check is that the water is actually being supplied to the appliance\015\012and is turned on. If it is then check the water inlet valve, if th ... Siemens 24 in. SE25T250 Free-Standing Dishwasher

LG LDF6810ST had OE error. Disassembled found no obstructions blew air through and vacuumed hoses to air gap and to disposer, no obstructions. Never heard pump run when starting cycle, so replaced drain pump. Still doesn't run. Looked at the service manual, and the only other suggestion is repair circuit? Is this the circuit on the bottom right of unit or the pcb up top? Wires and connections all look fine. What else could it be. Any suggestions appreciated!


Hi,Usually my First Response to this Common Error is :-Most likely pump trap is clogged up. Access it behind small door at front. Drain water out through small hose that is there otherwise water will be all over the floor when ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


... Dishwashers

On an AEG Favorit 64570 VI we have an error 20. Manual indicates a drainage problem, however when we pour in water, it gets pumped out without a problem. No obstructing in the exhaust tube. Next we checked the pressure sensor, by taking it out and blowing into it. It clicked as pressure was applied to it, so the inner switch worked. Everything is clean, but still we get an error 20. What does seem strange is that the appliance does not take in water. Any suggestions are welcome.


... AEG 23 in. Favorit 86070Vi Built-In Dishwasher

Aeg sensorlogic 50700 first showed c2 message; we drained & cleaned filters 3 times; worked half cycle and now showing error message c3?


Error message C3 is most likely indicating the flood switch is triggered. This means water is leaking from under the sump. The C2 error is linked to drain problems which you cleared. ... AEG Dishwashers

I have a kenmore elite dishwasher model # 665.13103k902. It was working just fine & then one day I ran the cyle and it lost all power in the middle of the cycle leaving water standing in the bottom. My husband checked the breaker and also unplugged it and plugged it back in and still nothing...any suggestions?


... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Kitchenaid model KDC-17 (old, but up to now working well) isn't draining after wash cycle is complete. cleaned the fiter, but water's still pooling at the bottom. afraid to run it and risk flooding the kitchen! suggestions?


... KitchenAid Dishwashers

Greetings. I have a Fisher & Paykel dishdrawer - the top drawer appears to have lost power mid cycle and the lid has not retracted - no led display - no response from the buttons. The bottom drawer functions ok. I have tried turning the power off at the wall for 30 seconds and on again. I have tried swapping the top and bottom controllers and the bottom still works but the top does not, so the controllers must be ok Not sure where to find the model number sorry. Any suggestions?


Describethe inside of unit,any wear on it anywhere, the rack the dishes go on is it plastic coated? is it wore with rust comeing though on tips here and there? ... Fisher and Paykel DishDrawer DS605FDSM Stainless Steel 23 in Builtin Dishwasher

My ADP6000IX dishwasher has stopped working. Put it on a cycle and it has started beeping and coming up with an error message err 4. Have cleaned out filter and wiped inside. Don't have the manual to check what this means. Can you help?


... Dishwashers

My LG dishwasher is stopping after a few minutes into the wash cycle with an error message OE and making a sound. The dishwasher tablet is still inside the dispenser and while there is water in the unit it isn't hot. Any ideas what is wrong, I don't have a manual


Hi rebeccasolom,OE means "Outlet Error"The drain pump is either clogged or the outlet hose is kinked.- Inspect the Drainage hose at the back for kinks.- Open the unit, and at the bottom sump check the small drain p ... LG 24 in. LD-12BW5 Free-standing Dishwasher

All the programme cycle lights come when any programme is selected. I have opened and cleaned the filters, drain pump and non-return valve. I have switched power off at the mains. I have also depressed the off switch for 5 secs as recommended on the Miele website and then re-started the machine. Still get the same error. Any suggestions would be gratefully received.


Hi\015\012\015\012Try and reset the dishwasher by following this sequence---\015\012\015\012Turn the power off to the machine.\015\012Press and hold button 2 and 3 together while turning the dishwasher on. The salt and i ... Dishwashers

Hello, I am having problems witha kenwood dishwasher, it just isn't cleaning anything. It seems to be going through the cycles and sometimes the dishes particularly in the top rack are a bit cleaner but in general they are uncleaned. There are no error codes. I wondered if the arms for some reason weren't turning correctly as some of the dishes were clean but this is inconsistent. I have tried changing detergents, adding more salt and rinse aid but it still isn't working, can you help?


... Kenwood Dishwashers

Got a Diplomat ADP8322. Starts Cycle then starts bleeping 3 flashes which is a heating error. No hot water at all. Had a look and cleaned watr pressure switch still not working. Any ideas has the heating element gone.


Possibly heating element - only way to find out is to check continuity with a multimeter.there is also a thermal cutout in series with the heater which could also have gone ... Dishwashers

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

Hi I have Bosch SKT 51 tabletop dishwasher, all has been well, came back to it one day and the cycle had stopped (its a dial). If i hold the power button in it still works. Any suggestions please. I have checked the Water feed in and the filter is not blocked, neither is the waste pipe


Hi.The problem is likely the switch itself. the switch should be part of the control pad, which I think is a single spare. A test on the switch can be done by reading impedance on the control pad wiring harness while operating the switch. ... Bosch 22 in. SKT5102 Free-Standing Dishwasher

My whirlpool dishwasher just stopped working the middle of the cycle with water still in the bottom and now nothing lights up or comes on and the water is just sitting in the bottom. Any suggestions?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing that should be checked is the Timer and then the\015 ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

I have a 3 year old delonghi dishwasher and have followed all the suggestions for error E4 on this ste and the water still wont drain from the machine and the error re appears. i have drained out all


... Dishwashers

I got a whirlpool dish washer Adp4407. When the machine is switched on it carries out the cycles but seems that the hot water cycle is not working and the dishes are still unclean even after completin


... Dishwashers

M/N PLD4555RFC3 I get blinking ER message with "wash" "dry" "clean" and "S" blinking icons All buttons have become non-responsive. Tried resetting by disconnecting power but error message comes back Only the Rapid cycle is now selectable. If I allow the unkt to cycle I end up with the error meesage above with the dishes only partially clean What could be the problem?


... Frigidaire PLD4555RFC Dishwasher

I bought a used GE Triton XL d/w with no manual. It worked great but now it is not cleaning anything, when the cycle is over the soap cup is open but half of the soap is still inside of the cup. I opened the d/w during a cycle and the dishes are wet top and bottom racks so I know it's getting water but the dishes are still filthy. Why is the soap not working? It's like water is spraying everywhere but the door where the cup is!


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... GE Tritonr XL GSD6260JCC Dishwasher

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

At end of the cycle E4 error message appears


... Baumatic 23 in. BDW10 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1107 seconds