Having problems with your Dishwashers ?

We have a Kenmore Quiet Guard 3 dishwasher, model # 665-74363. The 'Heated/Dry" light is blinking. I have tried the various reset combinations without success. Also unplugged the unit for awhile. Any suggestions? Thanks.


Answers :

When the heated/dry light is flashing that tells you there is a problem in that circuit. Which normally means that it is either the heating element or the thermostat. BUT could also mean that the float assembly is telling the control panel that water is still in the tub.

Check to make sure that the float assembly is not extended (sometimes it will get gunk on it and not drop when the water is gone). And if that is not the case, then you will need to unplug the unit and then pull it out and check the heating element with an ohm meter. If that is not the problem then you need to check the thermostat (should have about 240 ohms for a good one).
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a Kenmore Quiet Guard 3 dishwasher, model # 665-74363. The 'Heated/Dry" light is blinking. I have tried the various reset combinations without success. Also unplugged the unit for awhile. Any suggestions? Thanks.


When the heated/dry light is flashing that tells you there is a problem in that circuit. Which normally means that it is either the heating element or the thermostat. BUT could also mean that the float assembly is telling the control panel that wat ... Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I have a GE dishwasher model GLDL560N10SS. I noticed a burning smell coming from it the other day and then realized that although I can hear water running into the dishwasher when I start it, it never actually runs in the sense that the water is pushed through the various outlets to wash the dishes. I'm assuming that it is because the unit is dry and the heating element is still coming on that it is causing a burning smell. If I open the unit and reset it, it pumps the water back out into the si


The problem sounds like it is in the water inlet selonoid. Pull off the bottom panel and this is the part that the main water line hooks to there is a selonoid and it has a plugg inconnection to it unplugg it and check for power when the unit is supp ... Dishwashers

I have an Asko 1585 dishwasher. It drops the inlet valve on step (step 12), and the recirculation pump (next step) tries to pump with no water. Later at about step 47, the inlet valve begins to work again and the dishwasher finishes the cycle without a problem. I have had the board checked, and all of the power supply and transfer circuits are good. That leaves the processor. Is there any combination of buttons to press which can completely reset the controller board?


... Asko 24 in. 1585 Built-in Dishwasher

Kenmore 665.16762000 We were washing dishes the other night and my husband walked into the kitchen to find water pouring out of the "air gap" in the sink. Now we cant get the unit to come on. Ive tried some of the various combinations of button pushing to re-set, but so far still not operating. I am thinking it may be the "thermal fuse" due to some other questions here, but how can i confirm.... and the biggest question... how much is that gonna cost me to replace if i do it myself?


... Kenmore 16762 Dishwasher

I have an electrolux dishwasher model #=EIDW6105gS0. All lights are flashing on the console and will not let me select any of the modes...will not run at all. Is there any way to reset? I have tried cycling power to the unit and holding various keys....nothing works. Any help appreciated.


Hi,\015\012\015\012Sorry for the delay in replying to you, but there has been a technical fault and we have not been able to answer your question.\015\012\015\012The 6105G does not have a numeric display, so all of the ... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Gu2400xtps7 "normal" green light keeps flashing. Unit will not respond to anything. tried cutting the power off...still nothing. Can this be reset by pushing a combination of buttons? How do I know if it's the "Console Assembly" or the "Electronic Control Board"? I want to order the correct part. Thank you!!!!!!!!!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Bosch she43mo2uc dishwasher. When it's turned on I hear the pump but no water enters the appliance. I've unplugged the unit and toggle the reset switches. There doesn't appear to be any obstructions in the water outlets.


... Bosch Evolution 300 SHE43M02UC Dishwasher

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

My dishwasher will not turn on and the Start/Resume light will not stop blinking. Is there any thing you can suggest to fix this without my calling and paying for a service call? We have stopped, restarted and reset the unit as well as cleaned out the soap tray. We have also switched off the electric to the washer as well to no avail. Really cannot afford another service call again so please help us out. Thanks. Chris


Reset the control again. Then change out your heating element.\012\012That should fix it good.\012\012Have a great day! ... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

ASKO d 3122.. Keeps filling up the overflow area on the bottom of dishwasher. WHich sets of the overflow switch, then i get the flashing tea cup again. I will empty the over flow area. It will reset, We get one good wash out of it then on the next load it will stop work ing again and get the flashing Tea cup again, Back to unplugging the unit and draining the overflow area again.


... Dishwashers

My dishwasher (kleenmaid brandt super silent DW121TB) appears stuck in a wash cycle; how do I reset the program? I have read the instruction book to no available, tried unplugging power overnight, tried a combination of simultaneously holding buttons in and switching on, letting the machine run all night, drained the water and added clean unsudded water, and none have corrected the situation. There is also a selection lever inside the machine that is not identified in the instructions, it appea


When you say it is stuck in a wash cycle, do you mean the wash arms are continuously running?\015\012Is there water in the base when you open the door?\015\012\015\012Can you try to run the dishwasher in any other program like rinse ... Dishwashers

Kenmore 74362 My model# is 665.74362400 this unit is only just over one year old. My problem is it shut down and the quick rinse light started blinking. I have tried some of the button-reset procedures that were on some other responses but to no avell I even left it unplugged for a while. Any impute would be appreciated. I have a Kenmore Dishwasher Model #74362. After we run a cycle for a normal wash and heated dry the dishes are all very dirty and greasy. It is as if they were never washed. Th


I had the same issue and you will never beleive the solution.\015\012Steps to follow:\015\0121) run one full cycle with no dishes or soap\015\0122) run one full cycle with a dishwasher cleaner like Jetdry\015\0123) run one ful ... Dishwashers

I have a KitchenAid KUDI24SEWH2 diswasher I can start it with purshbuttons, it starts and then stops without finishing a cleaning cycle. Any ideas as to the problem? Is there a reset button? I've unplugged it and replugged with same results. Thanks confused


It may have something to do with it not being completely level. This interrupts the cycle. Also, if the door latch is not closed properly that can interfere with a complete cycle. If it is out of sync then you would have to unplug the computer boa ... Dishwashers

Kenmore Ultra Wash Quiet Guard 4 Dishwasher model 665160344000 normal wash light keeps flashing. I have done all of the push this button and that button combinations I can find on the internet. I unplugged and repluged the 14 pin ribbon with power and without power --no joy. Looks like I need a new part - which part?


Hi\015\012\015\012Open the door. Within 3 seconds press the following sequence\015\012--Try pressing normal wash, heated dry, normal wash, heated dry, normal wash,\015\012heated dry three times within 6 seconds and then press cancel to re ... Dishwashers

Whirlpool DU1145XTPPB7 Whirlpool DU1145XTPB7 model. Normal cycle light started blinking sometime during end of wash cycle. It will not do anything. Things I have already tried and not worked: 1. Unpluged and pluged unit back in. 2. System reset w/ heat-dry button, etc. Any help would be greatly appreciated


These dishwashers normally have a "Control Lock" mode.  It's in the manual.  It is provided for child safety.  It's often controlled by holding the "No Heat Dry" button for 4 seconds or more -- same procedure turns it on or off. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

Have a ge nautilus dishwasher, all the light in front works, except the start button will not light up, tried unplugging the power to reset unit, still do not work, any suggestion


... GE 24 in. GSD4060JSS Built-in Dishwasher

I have a kitchenaid superba dishwasher and the control panel is locked. we've held the button down for four seconds and more without any luck. we have also unplugged the machine hoping it would reset. do you have any suggestions?


... KitchenAid Dishwashers

Push buttons don't work except for the canel button. Tried unplugging the unit to reset it and that did not work.


... Kenmore 16024 Built-in Dishwasher

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

I own 2 model KUDS01FLSS1 KitchenAid Superba Dishwashers. The first unit had the clean light blinking so I read the post below and reset it. I thought everything was fine but half way during the cyc


... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Electrolux Dishwasher DX403SJ - 30 Overfill fault but unit is dry. Overflow sensor intact and all looks good. Think we need a reset code. Can anyone help?


... Dishwashers

My miele diswasher seems to be stuck on rinse cycle and will not advance...keeps draining and refilling. Can't figure out how to reset and restart new cycle, to clear the snag. What's going on? I have cleaned all the filters in bottom of unit per operating manual. Wish I still had my GE, where you could reset the unit...no button to do that on this overpriced unit.


Sounds like a broken timer. If it's a rotary dial, they're not too bad to change.... ... Miele Slimline G832SCi Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0905 seconds