Having problems with your Dishwashers ?

My FGHD2433K Frigidaire dishwasher is not venting when done. It stays hot and humid for hours and smells if I don't open it soon enough. In the user guide there seems to be a vent on the top and I can see it on the inside but it must not be opening because no heat escapes after the cycle.


Answers :

Hello, welcome to FixYa.\015\012\015\012I understand based on your post your dishwasher is a Frigidaire FGHD2433K, correct ?\015\012\015\012Typically with these it is less an issue with failure and more to do with blockages. My suggestion would be to remove the panel and visually inspect and clean out the condensation tube and vent assembly.\015\012\015\012If you are reluctant to do so without a guide, post back with an email and I can send you a service manual for the Frigidaire machines. I will watch for your reply and gladly help in any manner I can going forward asap.\015\012\015\012Regards,\015\012\015\012Macmarkus :)
Hello, Click this link http://c.searspartsdirect.com/lis_png/PLDM/R0909022-00002.png this is the diagram showing the interior of the door includeing the vent assembly. You would remove the screws on both sides of the inside panel in order to access the vent assembly in the unit you can remove part numbers on diagram 14 and 13 and assure there are no obstructions or debris stopping the flow of air. If you did need to order part 13 part number would be 154755801 and the part number for number 14 if you could not remove the debris on the inside 154784401 the total price from sears would be about 25 dollars for both parts together. If you have any further questions message me back. Thanks I await your reply
\015\012Rick
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My FGHD2433K Frigidaire dishwasher is not venting when done. It stays hot and humid for hours and smells if I don't open it soon enough. In the user guide there seems to be a vent on the top and I can see it on the inside but it must not be opening because no heat escapes after the cycle.


Hello, welcome to FixYa.\015\012\015\012I understand based on your post your dishwasher is a Frigidaire FGHD2433K, correct ?\015\012\015\012Typically with these it is less an issue with failure and more to do with blockages. My suggestion would be to ... Dishwashers

I have a F and P 603 dishwasher with a similar problem as to a recent post here. My top drawer doesn't turn on and my bottom drawer does. Well it just has after I swapped the "blue" motor inside from my top one. Now, I have tried and opened as far as the translucent "X" plastic from the bottom of my bottom drawer showing the motor and it looks fine. I have even swapped the control board from my top drawer to try and see if it works and it actually does. So, problem persists. Top drawer do


Alright, open up the outer panel of the machine. Note the positions of the wires on the switches and\015\012remove them, unclip the switch housing from the base panel. The\015\012switch housing contains one switch for each drawer. The switches are\01 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Maytag MDB7600AWB dish washer. I have a door leak, dripping from the right side. I can not see anything that would allow it. It seems like it could be coming from the inside of the door. Also, there is heat and condensation on at the top of the door, above the leak. It could be that steam is coming from the top right and dripping down the door. Could you give me some idea about fixing the problem.


HI,Check for the following troubleshooting steps:Some leaking around-under-from the door on dishwashers can be traced back to a split in the spray arm. If the lower spray arm develops a split in it, the spray arm can turn too ... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

Drying problem Hi Our 3-day old LG dishwasher is not able to dry our dishes. After the cycle is finished 2 hours later, I open the door to find that water is everywhere. As if the washer is skipping the dry sequence completely. The "vent" on the inside of the door doesn't seem to have an outlet--why is this a vent if nothing can escape? The owner's manual says to use a rinse aid to help drying. I don't believe in using band-aid's; something else is wrong. Any help/advice is appreciated. Thanks,


Hi,\015\012\015\012As I had the same problem, I worked on my machine and found out the heater unit was not working (it is a brand new machine ! - remark : as I moved overseas, LG did not cover it with their warranty).\015\012\015\012But b ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I have a Whirlpool DUL300XTLQ3 Queit Partner III. The cleaning blades stopped moving-started it-waited awhile-opened it-the blades were in the same position. Took the bottom blade+filter cover off. Then I held down the metal piece on the case and switched on the micro switch on the door to see it running with the door open. The water shot straight up about 4-5" that's it. This does not seem to be enough pressure for the water to get all the way up to the top spinner. Am I looking at a new pump


If there is not enough water, the dishes would not get cleaned. Thiscould be caused by a partially closed water shut-off valve (locatedunder the sink), or a faulty dishwasher water valve (located at thebottom of the dishwasher, behind the kick panel, ... Whirlpool Dishwashers

My whirlpool dishwasher is not washing the dishes properly. when finished cycle, I still see the dishwasher tablet half used. The grey long piece at the back, seems to have come out of the two holes it fits into on the "floor" of the inside of the machine. I've clicked it back into place, but it still pops out. Sometimes the rotating sprayer at the top and bottom, don't move either when its out of place. please help.


... Whirlpool GU2400XTP Built-in Dishwasher

About a 3 year old maytag stainless steel inside dishwasher, not cleaning, often soap resdue on dishes or silverware, I use fresh new cascade, checked to see if washer fills with hot water, seems to up to the bottom of the door when I open durning cycle, arms go around, no obvious plugging of the screens, no junk in the foot chopper propeller, no paper or plastic or food in the jets of the arms. Motor went out on it 9 month ago and I had it replaced by appliance repair station here in Missoul


Water must be 130 Deg F to wash properly. ... Maytag Dishwashers

Hello, We have a Candy Diswater that is just arround 2 years old. When it starts it takes water and then you hear the washer going into loop. It tries to do something els but doesn't seem so. If you open the door you can see water inside but no progress or heating. If you also try to change the program it doesn't change as well. Before it got to this point sometimes we used to unplug the power and tunr it off and then ON and then it works. However, now this procedure is not working an


Quite possibly could be the timer and could also be the main control board as well. Sometimes unpluging it will help for short times but if a serious problem persists it will only be a temp fix... ... Dishwashers

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

Bosch Dishwasher I have a stainless steel Bosch dishwasher, I made the "mistake" to try to see if I could fix the jammed handle from the door. Unfortunately, (did not realize the top panel comes off without opening the entire door). I removed the screws from the door frame (Inside panel), and the door springs/latched got loose. I would like to put it back together, but I dont have any diagrams on the door to make sure all parts are in place to put the door back together. I have been havin


Hi ED,\015\012\015\012It sounds like a real problem here. If the springs are still in one piece, my best guess is to to remove the springs from the door. Then attach the springs to the dishwasher body first, then reattach the spring to the door. Not ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

My Zanussi DS17 slimline dishwasher is leaking from below the door at the front. The inside seals all seem to be fine, but the catchment moulding below the door (which is revealed at the front when the door is opened) is filling up with water, and then overflowing. I can't see where the water is comming from, but it is definitely the water from the washing cycle as it's hot. Any ideas? I haven't dragged the maching out from the wall yet, but I may have to. David R


Hello,\015\012Have a look at the bottom spray arm and check the ends of the arm for splitting as this will cause the water to be directed at the door lower section and leak.Try taking arm out and run for a short while and see if it stops the le ... Dishwashers

I have a Bosch SHX98M dishwasher and the top arm will not rotate. I can see water coming out of the holes when open during a cycle and I have made sure there are no obstruction for the arm or anything stuck in the arm feed line. I just had a technician here who was at a loss and did not think the pump was bad since alot of water is being pushed around inside. The bottom arm works fine.


... Dishwashers

Dishwasher, nautilus, doesn't spray water out the top arm? I'm haivng to wash dishes 2 times, and still no better results. I've tried opening the door fast during a water cycle to see which is the problem - can only figure it is the upper arm, the lower arm seems to have water coming out, can't tell if the tower raises completely up.


The jets on the arms can sometimes get blocked with food bits that have got past the filter. This reduces the water flow and rotation of the arms.The arms are easy to remove without tools (they are intended to be removed by the user). ... GE Nautilus 24" Built-in Dishwasher

Hello, Im trying to diagnose poor cleaning of glasses in the top rack of my Fridigaire FDB751SCB0. everything seems to work fine but while testing I noticed the upper arm isn't spinning. the lower arm is. i believe the pump is working as water is spayed everywhere inside but no matter which position I leave the upper arm in, I find it in the same place when I open the door. what could cause the upper arm to not get water preventing it from spining?


Hello; first thing to check, which you don't mention, is which side of the glasses aren't coming clean; the outside, which would be caused by the TOP spray not working properly, or the INSIDE, which would be caused by the spray BELOW the top rack not ... Dishwashers

Dishwasher i have fixed the fridgadair dishwasher so that i can see what it is doing with the door open; water is coming out of the spinner arms but the arms are not spinning ; it seems that water sprays about 4 inches in air; the top is feed water off and on but not constant.


  This dishwasher does not feed water to top and bottom arms at same time.  It starts with bottom and then after awhile it switches to top and then cycles.  If water comes out arms but arms won't turn,  check all holes in arms.&nb ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My GSD900G-01 dishwasher leaks where the hot water is supposed to go into the tub. There's a plastic fitting that seems to be glued to the side of the tub and the hose from the inlet valve goes to the top of this fitting. There are no visible cracks or other damage but there is some rust inside the tub at the fitting. The fitting has two open gaps on it's side which is where the water is leaking out. It looks like the water is supposed to flow past these gaps (which I'm guessing are there to


Hi, I seen where this posted on premium. If you still need assistance, please let me know. I can help you through this.\015\012\015\012Vic ... Dishwashers

Maytag MDB-4 Dishwasher Door Leaks and doesn't fit tight against the tub. The metal latch attached to the top of the tub isn't adjustable and I don't see anything inside the door opening to adjust. Any tips? Thanks!


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101 ... Maytag 24 in. MDB5651A Built-in Dishwasher

The door won't close. The latch seems jammed. I have tried setting and releasing the child lock inside the handle. The problem seems to be with the latch itself. From inside the door, I can see the tongue the clips into the latch, but it seems stuck. I can't get it to move, even with gentle force.


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

- the dishes and glassware on the top rack are not coming out clean - I checked the course strainer to see if it is being blocked but don't see any thing there - I also took out the spray arm that sprays up into the top rack and ran water through it with a hose - it also appears to be free of clogs. - I don't see the spray arm spinning when I open the door during the wash cycle - - lastly, it may be unrelated, but the dishes are not coming out of the washer as hot as they used to be any i


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Frigidaire dishwasher (Electrolux FDB750RCB0) does not move water through the hose to the upper wash/spray bar. The lower wash/spray bar has pressure enough to turn. With the dish washer out from under the counter I can see the water rise very slowly up the translucent hose. If I remove the check ball under the stem assembly in the motor in the bottom of the tub, water flows, but I'm not sure if the top bar turns then (with the door open I see water coming down from the top, but never saw


... Dishwashers

Kenmore dishwasher type 573-D, model 665.16034402. Items on top rack don't get washed. Items on bottom rack are washed fine. Appears top sprayer and maybe middle sprayer aren't getting water. At rear of washer, top rubber flapper valve (which feeds middle sprayer when top rack is in raised position) is stuck open, bottom flapper valve looks OK. We use top rack in raised position so this doesn't seem to be the problem.


... Kenmore Dishwashers

The dishes are not clean when we run the wash cycle. It looks like the water flow from the top sprayer is NOT working. The door, when we open it, has undesolved soap stuck in globs on the top of the door. The top dishes are not clean and some of the botom dishes are not clean. We've run some clear washes to see if we can find the problem. The water flow looks suspect. Is it in the electronics or in the water mechanics. I called the repair guy who ususally comes out and says buy a new one! The re


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... LG 24 in. LDS 5811 Built-in Dishwasher

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

I own a Miele G977 Plus dishwasher. There is what looks like a vent at the top left corner of the door. During the course of a wash a noise that sounds like a fan comes from this vent. Whwn the wash is complete and I open the door of the dishwasher water flows out of the vent onto my kitchen floor. What is the problem and how do I rectify it. Tom


Hi Tom, welcome to Fixya.\015\012\015\012The issue is likely just the blower and housing drain hose blocked with "crude" from time & use. If you take the door panel off ( watch those edges they are VERY sharp ) and unfasten the control panel as well ... Dishwashers

I have a Whirlpool dishwasher that won't clean the top rack. The spinner for top rack is not spinning. I can't seem to get to the screen to see if there is a blockage.


I have a du1148xtpb1 whirlpool dishwasher and the top rake dishes are not getting clean please advise ... Whirlpool DU1055XTS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0762 seconds