Having problems with your Dishwashers ?

Inglis dishwasher - clean light flashing & when start button pushed, it flashing quickly 3 times


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Inglis dishwasher - clean light flashing & when start button pushed, it flashing quickly 3 times


... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

Kenmore dishwasher 665.16029402./ clean light flashes 7 times. i did the push button sequence to reset. started to wash for awhille and during the wash it stops and green light starts flashing again


... Kenmore 24 in. 16032 Built-in Dishwasher

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

I have a kenmore dishwasher mdl#665.16022401the clean light blinks all the time and i push the cancel button and then wash and the start and the start button light blinks 3 times and nothing happens.the clean light is still blinking.


... Dishwashers

I have a kenmore dishwasher mo. no.665.17039401 the clean green light flashes 7 times and it keeps doing that if i try to start the dishwasher on the start button a red light flashs three times what do how do i fix it .i made shure the door was locked


... Dishwashers

Hotpoint BC145 Dishwasher not cleaning starts to kick in but then just sticks on the "R" light flashing and cannot reset even after turning off. Itbeeps when pressing the select button sound weaker and shorter than they used to and the light does not move from the "R". On a couple of times I have tried it has reset and then the dishwasher starts but after about 3 minutes there is a low beep(not the usual beep when a programme finishes) and the washer stops and the light is flashing on the "R" ag


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

Hello, We need some assistance with our Kenmore dishwasher. Last night after I started a load, the dishwasher just stopped and then the washing and drying lights started flashing red, sanitized and green are flashing green and the 6 hour delay button is flashing red. I have pushed the start/cancel button but to no avail. My husband shut the power from it to see if it would reboot, it does not help either. It runs a little bit then quits and does not clean the dishes. Could you give us sugg


Hold the start button for 3-4 seconds and see what that does ... Dishwashers

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

We have a Bosch SHE44C02UC/46 that suddenly won't start. I pushed the on/off button to start the dishes cleaning on the 'Power Scrub Plus' cycle and the display lights up with a 125 min. indication for the cleaning time, but the dishwasher never starts. It just sits there completely silent and never begins the cleaning. The dishwasher has worked perfectly up to, and including, the last cleaning cycle (3 days ago) for the last 4 years. Suddenly, today, nothing. Zip. Zilch. Nada. I don't get i


Hi.Re:" I\\'m sure it has to be something simple." A: yes, probably a fault, simple as that.To start there is a recall concerning this model. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Diswasher malfunction - won't start clean light flashes 7 times The clean light keeps flashing green. Can't get the washer to start. The only operation it will do, is drain when the cancel / Drain button is pushed This unit is: Stock # 16029 Type # 575-0 Model # 665.16029.402


This information may help in your situation. This can be a common problem on some Whirlpool manufactured dishwashers. The following link explains how you may be able to clear the blinking clean light problem: ... Kenmore 24 in. 16029 Built-in Dishwasher

Dishwasher will not start. The clean light is flashing on and off. If I push the cancel button it appears to be draining but there is no water in the tub and it just continues. When I push the start button if flashes for a few seconds but then goes off. Thanks


Hello & Welcome to FixYaFlashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:High te ... Kenmore 24 in. 16039 Built-in Dishwasher

I have some problems with a Whirlpool DWF 406 dishwasher: The other day, my wife complained about it not finishing a program (just stopped and started bleeping). I saw a post at this forum where it said to clean out the black grid down my the sump. I did that, and then the dishwasher worked fine a couple of times. Today when I got home from work, the machine just bleeped at me and and the green LED light by the start button flashed 9 times over and over again. Does anyone know what those 9 flash


We have the same problem. The dishwasher is 10 years old. In one of the German forums they said that usually it's because the sieve ahead of the membrane has a fine layer of sludge and the pump cannot pump out the dirty waste water. They said that yo ... Whirlpool Dishwashers

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

Jenn-Air 24 in. JDB1080AWS built-in dishwasher green lights flash on and off on their own sometimes - not able to start dishwasher sometimes - not able to use settings (lights don't light when pushing top setting buttons - dishwasher seems hot about 8 - 12 hours after use = cleans very well though - dishwasher wasn't used much from 2005-2007


... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

My clean light is blinking on my kenmore 16029 dishwasher and it won't start after I push the start button. The clean light is following a pattern of blinking 7 times and stopping, then repeating over and over again.


... Kenmore 24 in. 16029 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2995 seconds