Having problems with your Dishwashers ?

Water problem with dishwater.

\015 Both the water pumps are turned on and lights all going , however there is no water entering the dishwasher. help?\015

Answers :

You may not be getting power to the inlet solenoids, if you have a multimeter you can test them and see if they are being powered or not.
The other options are that the inlet solenoids may be dead, wires could be off the solenoids or it could be an electronic fault with the controller.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No water entering the dishwater. water supply is hooked up and water supply valve is in the open position. Could this be a water pump problem or is there a cut off valve entering the back of the washer that could be in the closed position?


No cut off on washer check float switch make sure its free check water valve make sure wires are on it and water getting to it ... Kenmore Dishwashers

Hello, My Ariston LSI 68 A dishwater have a problem: During the washing in reduct mode,(the 3rd program from left) after about 1 hr , he does'n end the washing and blinking the second light from left. (the normal washing program). In the dishwater still remain about 1 inch of hot water, the drying never start. If you can send me the blinks codes of my dishwater i appreciate very much. Thanks Leonardo Italy


The Ariston dishwasher alarms should be in the user manual. However, I cannot find the manual for your model. \015\012\015\012But I have found ... Dishwashers

Water problem with dishwater.


You may not be getting power to the inlet solenoids, if you have a multimeter you can test them and see if they are being powered or not. The other options are that the inlet solenoids may be dead, wires could be off the solenoids or it could be ... Dishwashers

Our dishwasher makes a terrible jackhammering noise during the parts of its cycle when pulling water. For the longest time we thought it was our very old plumbing and that we had a pipe 'hammer' and ignored it. We have just had the kitchen replumbed and this problem has not gone away. It's very loud. The plumber said it had to do with the pressure valve in the dishwater - do we get a technicial for this.


Hello,Welcome to FixYa.Based on your description, it is indeed water hammer and ... Bosch SHU9925UC Built-in Dishwasher

The inside bottom of our CMA dishmachine is pitting and has a hole through it. It is supposed to be stainless steel. The company said it was because we had too much iron in our water? We had the water tested by 2 sources and found that not to be the case. We had it for 6 months when this started to happen. Now CMA will not replace it because they say water problems are not covered. We don't have a water problem. Has anyone else run into a problem like this?


This is usually caused by a leak in the plastic chemical line on the sanitizer. Over time and it doesn't have to be long time for it to happen, the chlorine sanitizer drips on the stainless causing it to pit. Contact your chemical supplier to check ... Cma Dishmachines AFB Dishwasher

My LG dishwasher upper rack has stopped cleaning. The uppermost arm is seemingly getting no water at all and the arm on the underside of the upper rack is getting some water, but not enough to turn it. I have already disassembled and cleaned all the way down to the diverter assembly and it has not fixed the problem. I think this is a problem with a the (?) diverter pump or perhaps a sensor that sends water to the upper arms. I am trying to figure out how to further diagnose the problems. The


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDF6810 Built-in Dishwasher

I have a Dishlex Global 500 dishwasher (DX500lWW*b). Woke up the other night to find water all over my kitchen floor. The hot water hose connector to the hot water tap split (bursted). The dishwater was not in operation at the time but I can only assume when the hose bursted the dishwater came on to alert me? the code on the dishwater is displaying ''oF'' - which means Incorrect fill level of fill time. I have consequently had the hose connector repaired but the display still has the code ''oF''


I found this\015\012\015\012"Hi - answer I was given by Electrolux Help was: pull machine out from under bench onto old towel, tip GENTLY onto left hand side (your left as you face the front of the machine) after it has drained, stand up ... Dishwashers

Check water light stays on rendering machine unuasable.checked water supply.all filters .googled problem told me to switch water supply on and off rectified problem for 10 minutes then check water light came back on. water remains in bottom of appliance.


... Bosch Dishwashers

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

We recently bought a house with a Kenmore 363.16222100 (?) dishwasher. No manual. Monday night it didn't drain properly and leaked some water on the kitchen floor. The cycle had finished when we saw the water on the floor. We bailed out the excess water. I took off the drain cover and insert. I couldn't see an obvious clog problem, but cleaned it out. Then I tried a short cycle, interrupting it to shorten it. No problem. Water seemed to drain fine. I did find a part that looked like a straw and


HelloWelcome to FixyaMy name is Huum,You can find your model dishwashers manual here at this site. this sitehttp://www.managemyhome.com/mmh/lis_pdf/OWNM/L0801624.pdfI feel you should not invest blindly in someone ... Dishwashers

I have a Husky pressure washer with a Honda 2600psi engine. Problem is, no water will come from the pressure hose. I connected the water w/out the pressure hose and water flows thru strongly. I then connected the pressure hose w/out the wand and water flowed thru the hose fine. When I connect the wand and pull the trigger, nothing. I have replaced the wand and that was not the problem. Please help.


Check the quick disconnect to the wand these are spring operated and can get stuck ... Pressure Washers

Took these from a previous page, because this is what is happening to our lab Miele Platinum G892/G892 SC. Can you tell me what the problem is and how to fix it? Thanks. intake /drain light is flashing,full water- Guest Feb 26, 2009- I have same problem - open the door and there is water at the bottom of the dishwasher - when I restart program, the water drains out fine. Also, I have great water pressure coming into the dishwasher, filters are clean, etc. I am suspecting it is a circula


If there is verified power at the pump motor - your timer is defective.Thanks For using Fixya!! ... Dishwashers

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

I have had a repairman come out and look at this and he says all the diagnostic test say everything is okay. My problem: my dishes come out dripping wet...like it hasnt dried anything. Sometimes dishes are still dirty. I don't think there is any heat getting to anything. I run the water in the sink beforehand to try to get the water hot. I used this dishwasher for 1-1/2 years with no problems and now I have this problem. What is going on?


I am having the same problem but do not see any posted solutions. Have you solved this problem? ... LG LDS4821ST Stainless Steel 24 in. Built-in Dishwasher

My dishwasher (indestit) will not fill up with water. A technian came today and advise that there was very little water coming through the hose and therfore had a blockage. I replaced it today and it fixed the problem, however onn the 1st wash the cycle appeared to stop rather than completing fully. I have since tried to restart and have the same problem lights 2 and 3 are flashing indicating there is no water getting through, how can this be.


Hi,Here is a tip that will help you to find out why water will not come into thedishwasher... Dishwasher Trouble No Water entering Dishwasher ... Dishwashers

Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the dishwasher but it's like there is no pressure behind it to force it through the holes in the propellers so it's just kind of dumping water out as opposed to having any forced pressure. Hope this makes se


Try adding some more water to the machine after it has done the fill cycle do not over fill it. if there is no change in the performance the you need to replace the main wash motor.\015\012if there is achange the you need to change the fill val ... Dishwashers

Kitchen Aid model KUDS01FLSS3, water gets pumped into bottom of dishwasher but when the cycle needs to change to shoot the water over the dishes nothing happens. When the cancel button is pushed all the water will drain.I have cleaned out the bottom drain compartment that was jammed with calcium build up and guck. Would this be a pump /motor problem or electrical circuit board problem?


... KitchenAid Dishwashers

Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the dishwasher but it's like there is no pressure behind it to force it through the holes in the propellers so it's just kind of dumping water out as opposed to having any forced pressure. Hope this makes se


Water will flow out of your inlet pressure. The pump takes from your machine to spray. The same water is circulated during wash!Hence try the method I have informed you. If it is a micro controller problem you have to contact the service ... Dishwashers

Hi there, Ok, i think i'mHi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the More Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. In\015\012this case you’ll need to check the water inlet valve. Disconnect the power\015\012source to dis ... Dishwashers

We have a Siemens dishwasher SE25M851. It had the check water light on, so we have checked all water flows which seem fine. There is what I think is an Aquastop connected to the water hose, which I have no idea if the problem is there, but when I now put the dishwasher on there is a burning smell coming out of it, so have had to turn off power supply. Can you shed any light to the problem?


... Siemens Dishwashers

I have a bosch sms46 au dishwasher and it is having problems filling with water, there is no problem with the water supply and the water is getting thru but slowly any sussestions?


... Bosch Dishwashers

The start timer control cycles but nothing happens. The motor seems to gurgle while attempting to fill with water - but no water comes through. We have had this problem before and the repair person replaced the timer control board. Could this be the same problem reoccuring? I have also tapped and cleaned the water float as described by GE website.


I bought a new one and installed it myself. hardest part of installing was taking the old unit out. I compared the cost of a second repair of a 10 year old dishwasher vs. purchasing a new one. We also checked the pump and solenoid to find problems th ... GE Nautilus 24" Built-in Dishwasher

Maytag Quiet Series 300 dishwasher leaves sediment on dishes (primarily glasses) after running the Autoclean cycle. We've taken it apart, cleaned spray arms, filters, float and replaced some seals, but still have problems. We use Cascade detergent and Jet-Dry (what was recommended when we bought the dishwasher). Our water temperature is 120 degrees (maximum setting we can have without having our tankless water heater modified), but this dishwasher problem was an issue with our old tank water hea


The problem is hard water. www.dishwasherfilter.com has a\012product to solve this problem once and for all. It filters the water going into\012your dishwasher and remov ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

This is a past problem posted that I am now experiencing with my Kenmore Elite Model 655.17489300 dishwasher. Looking for any suggested solutions, Rick Past Problem: I have the same problem with my 2004 Ultra Wash Model 665...fills with water, sensing light comes, then stops for a second. Then you can hear another pump kick in (it hums) and just runs continuously but no water is spraying through the arms. When you cancel the wash, it drains perfectly. I've checked the filters, all is c


The symptoms you have mentioned could be linked to the soil sensor which some models come with. The purpose is to run the drain pump and let more water flow through inlet valve if during wash cycle the dishwasher detects soil collection in the accumu ... Kenmore 24 in. 16539 Built-in Dishwasher

I have a bosch smu 2000 series dishwasher. it has always worked well with no problems but then all of a sudden a week or so ago, the water stopped coming into the dishwasher to wash the dishes. the faucet and all other water areas continue to work w/o problems (i.e. bathroom, shower etc). in attempting to use the dishwasher, the entire cycle seems to be working, i initially hear what sounds like an initial water discharge when the cycle first starts and during the entire cycle it sounds like it


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1274 seconds