Having problems with your Dishwashers ?

Kenmore Dishwasher has died part way through a wash cycle.

\015 Kenmore Dishwasher model 665-76962K601 purchased 2008 has stopped working. Just stopped near the end of a cycle leaving a small amount of water in the bottom and dishes still unfinished. No power to the controls with door open or closed. I have not opened it yet.\015

Answers :

The control module has failed, you can check for broken solder joint s or obvious damage but it's hard to diagnose the exact cause remotely.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore Dishwasher has died part way through a wash cycle.


The control module has failed, you can check for broken solder joint s or obvious damage but it's hard to diagnose the exact cause remotely. ... Dishwashers

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???


Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

KENMORE MODEL # 363.16222100 Hello - my dishwasher (model# above) is currently filled with H20 and will not drain/work. When the knob to select the dishwasher cycle to begin is turned, it just 'clicks' and does not engage the washing cycle. When I tried to just let it run the cycle as is to 'restart', it had an electrical odor to it., Currently the knob is at the 'Rinse & Hold-(Heated Dry Off)' part of the cycle and all dishes have been removed. I would appreciate any assistance available. Thank


Either the motor is locked up or the control failed. You will need a service visit. If it is over 10 years old, I would buy new. ... Dishwashers

CDA dishwasher is constantly beeping part way through a wash cycle and obviously stops washing at this point. CDA have been out three times in the space of four years and it costs £79 each time. Could have bought a brand new dishwasher by now. The man who repaired mentioned it was the sensor and showed us how to clean it but I don't know anyone else with different makes who have to go through this hassle every two or three washes and this is now making now difference.


... Dishwashers

BEKO DWD 8650W DISHWASHER, AFTER HAVING GUESTS HOSE SIT FOR US WHEN ON A WASH PROGRAM (ANYONE) PARTWAY THROUGH THE CYCLE THE PROGRAM SWITCH EMITS A BUZZING NOISE FOR A PERIOD OF TIME THEN STOPS, AND CARRIES ON WASHING AS NORMAL. LAST NIGHT IT STARTED A WASH BUT STOPPED PART WAY THROUGH THE WASH AND THEN POWERED DOWN THEN BACK UP AGAIN BUT ALWAYS STUCK AT THE SAME TIME IN THE PROGRAMME, i TURNED IT OFF AND CHANGED PROGRAMMES WHERE IT EVENTUALLY MADE IT THROUGH A 30MIN WASH PROGRAMME, WITH THE BUZ


Dosent heat up or dry ... Beko Dishwashers

Dishwasher fills with water, then empties, fills then empties, and repeats this cycle a few times - then decides to work. then part way through cycle - it repeats this frustrating cycle, making the whole washing use loads more water and take much longer


Hi,\015\012Your dishwasher may pre-heat the water. If so, and if the water entering the dishwasher is cool, the heater may take up to half an hour to heat the water.\015\012To avoid the wait, increase the incoming water temperature before turning on ... Fisher and Paykel DS605I Built-in Dishwasher

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


Hi There,\015\012\015\012Your description seems to indicate a fault in the water heating circuit or components. This is often the reason for a wash cycle not finishing and draining. As the machine will drain when you lift the overflow lev ... Dishwashers

Kenmore dishwasher model number 655 16022400 has a flashing green clean light. Reset panel and now the washer will not complete a wash cycle. The washer stops at the drying part of the cycle. What is the problem?


... Kenmore Dishwashers

Model d2pdwi 854234715810 dishwasher trips house fuse part way through wash cycle. Rinse cycle works ok and water is comming in and can be pumped out. You can hear it clicking like its trying to activate something 1-2 time and then trips fuse.


... Whirlpool Dishwashers

Tripping out hi, part way into the wash cycle the dishwasher shorts out,so does all of the house,;so I unplug the dishwasher,and reset the mains.can anyone help,;thanks,dave.


I had the same problem once before. It was only after a few months that we realised it was the dishwasher causing the power cuts. I looked behind the dishwasher to find the back of it had melted. I was renting at the time, so the real estate agent re ... Candy 24 in. CD950 Free-standing Dishwasher

It won't complete a full wash cycle keeps stopping part way through and low rinse aid, low salt lights flashing even though both are full ??? Pamphlet says this might also mean there is a kink in the inlet hose but that seems fine as well. Have had the dishwasher 3 weeks and it has completed about 4 cycles without stopping ???


Check water valve to see if it has something blocking water supply ... Dishwashers

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


... Dishwashers

KENMORE DISHWASHER STUCK IN WASH CYCLE it will not move off of this postion water heats up it cleans but does not move off this cycle. New 2008 Kenmore 1610 built-in dishwasher won't leeave wash cycle. repair person says it is supposed to take 3 hours.


... Dishwashers

Kenmore ultra wash quiet guard deluxe The cancel/drain light(red) comes on part way through the cycle and stays on.


... Dishwashers

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

Grinding The situation: I have had my Whirlpool DU915PWPB1 for 2 1/2 years, it isn't the greatest dishwasher but does the job good enough. Recently, the water will fill, the washing cycle will run but then when that part stops it goes into a whirring that seems like a motor is going but nothing is moving. I have removed the Filter Modual in an attempt to find out what the grinding would be. There doesn't seem to have anything in the way or under the filter. I have ascertained that the grin


Noise probably not from there when reassembled the plate will not be direct contact with screen noise is probably from wash motor itself..suggest checking owners manual for warranty info ... Dishwashers

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

I have a GE GSD2000J01WW Dishwasher in a building with low water pressure. The inlet hose is 3/8" OD. The heating coil gets too hot and gives off a bad odor as there is not enough water at start up. Is there a way or a replacement part that can be used to change the timing of the heater and wash cycles, etc.? Thanks


... GE GSD2000J Dishwasher

I have a Kenmore model 587.1610 dishwasher that doesn't fill all the way when starting a load. I checked the float switch and it is working fine. The fill soleniod is also working fine and is clean. It just seems to time out before it fills all the way.also to compound the problem it doesn't seem to want to start all the wash cycle even after I have re-started the machine and it has filled to capacity. please help thanks Danny


... Dishwashers

The green clean light is flashing on my Kenmore Elite Ultra Wash dishwasher. After the reset sequence, the washer will run only 1 part of it's washing/drying cycle, then flash the clean light again... I have only owned it about 14 months, and this is the first problem I have had.


You may just need to reset your control board. Go to the link and it will explain how to reset the control board as well as explain what might cause the issue and how to fix it.http://www.appliancerepairlesson.com/dishwasher-2/dishwasher ... Kenmore 24 in. 17032 Built-in Dishwasher

I have an Indesit d62 dishwasher, approx 10 years old. It gets stuck part way through a wash cycle and I have to switch it off and move it on manually for it to finish it. Could you tell me what is wrong and how much to fix?


... Indesit 24 in. D61 Free-standing Dishwasher

I have a kenmore dishwasher model 66516382300 it would stay on wash cycle and not come off, appliance parts told me to put a new electronic controller on it, I did and the little green light comes on it will blink seven times and hesitate and do this over and over. What can I do.


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2324 seconds