Having problems with your Dishwashers ?

Dishwasher kdw60x10 cant select programe 1 only programe 4

\015 Kdw60X10 cannot select programe need to use programe 1 which is the 3 in one programe but it will not select this programe or any others only programe 4\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher kdw60x10 cant select programe 1 only programe 4


... Dishwashers

Dishwasher hello cant set program , when i push P it goes to selected program but when i start it came back to second program and runs that one


It could be you opened the door before it had fully completed a program, and then turned it off. My Hotpoint machine has to be reset in these circumstances otherwise the next time it is turned on, it appears to let you select a different program but ... Hotpoint Dishwashers

Belling Dishwasher IDW450. When turn on power button it starts bleeping. About 25 times. The you can select your program, it sounds like it is draining but then doesnt do anything else. Cant hear any water running in. I have turned the power off and back on. Water is connected


When you say you have turned the power off and back on. do you mean the switch on the appliance. if so turn off the power by removing the fuse from the fuse panel for the dishwasher. wait about ten minutes, put the fuse back in and see if that res ... Belling 24 in. IDW603 Built-in Dishwasher

I have a Diplomat ADP 8242 dishwasher. When i select program dishwasher starts working but then beeps when opened no water has been brought into dishwater and program light 2 & 3 flashing 5 solid. Have tried reset and works like instructions states. But when I have re-tried dishwasher same fault happends again. Any help


... Dishwashers

AEG Favorit 80820 dishwasher tablet door opens as soon as switched on and door closed. When you put the power on and select a wash and then close the door the small grey dishwasher tablet inside the door can be heard to open as soon as the door is closed. Normally this door remains closed until asked to opened automatically by the dishwasher at the correct point in the selected wash program.


... AEG 24 in. Favorit 80820 Free-standing Dishwasher

The program control on my flavel fdw60 dishwasher has all the programs showing up as selected and will not advance onto one single program


... Dishwashers

2000 G 879 SCVi Miele Dishwasher: Problem: When I turn the dishwasher to on, then select wash program, all the program lights start flashing until I push the "off" button


... Dishwashers

Dishwasher want let me select a program,but is still beeping.led lights on program selection not lighting up.


Would be helpful if you can post a comment to mention the make and model no. of the dishwasher.\015\012\015\012Have you tried to turn the power off and on at the mains switch? ... Dishwashers

I have a 2 yr old LG dishwasher model LD-1204M1. We have noticed that the dryer function is stuck on permanently even before we have selected a program and during a program. After a cycle finished the dishwasher would not turn on until sometime later. Any advice or ideas what could be wrong? Thanks


... LG Dishwashers

Smeg dishwasher ST1145S is not working. After I entered the selected washing program and closed the door, the program failed to start. I am not sure is because of no prolonged disuse or because of I have forgotten to turn off the on/off switch for almost 2 months but I heard there is a beeping sound which supposed to start the program and water intake. But all this is not happening.


... Smeg 18 in. STX45-1 Stainless Steel Built-in Dishwasher

Used some washing up liquid instead of dishwasher tablets, after i got rid of all the bubbles and drained it, it no longer starts. If i switch the power off and leave it for a few minutes i can select a prgram it starts and a few seconds later there is a beep and the solid green run light on the program selectoe is flashing over the left hand program button. At this stage pushing any program button does nothing, i have to swith the power off and wait 5 miniutes and the the above patten is repeat


Dear sir vif you have used liquid soap in your dishwasher it will make mountains of bubles to kill all bubles outin a hurry take a sos pad put it in your machine and run the dishwaser this will remove all of the soao instantly try it it really works ... Ariston Technologies Dishwashers

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

Hi, I have a Siemens SE24A230GB/17 dishwasher and it is not completing the wash cycle (any selected). It appears to be stuck on the 'wash' part of the program. I have done the reset actions as advised in the User Manual and tried another program, without success. I have found that the possible causes could be the timer or thermostat. The estimated time remaining display counts down, but the program does not complete the wash and move onto rinse and dry. Any help or advice you can provide would


... Siemens Dishwashers

Smeg dishwasher ST1145S is not working. After I entered the selected washing program and closed the door, the program faked to start. I am not sure is because of no prolonged disuse or because of I have forgotten to turn off the on/off switch for almost 2 months but I heard there is a beeping sound which supposed to start the program and water intake. But all this is not happening.


... Smeg STX2 Dishwashers

I have a Baumatic BDW 45.1 slimline dishwasher, the unit will power on but I cannot select a program. I was able to place the unit in to reset mode once by holding down 'P' and power cycling the unit. This then allowed me to choose a program and complete a full wash cycle. Now I cannot repeat this steps and the unit remains with just power light on. There are no Error codes displayed at all. Could this be a problem with the front panel?


... Baumatic 18 in. BDW45.1 Built-in Dishwasher

F&P Nemo dishwasher. Srart/reset light blinking 4 pulses. Program select knob won't rotate to select wash, rinse only available. Unit is clean, filters clean, water supply filter clean. I am an electrician but owners manual doesn't help.


... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

My CDA CW497 has developed problem. When i select a program say 70 degrees and press the start button and close the door the dishwasher starts in the the normal way bit after about 15 seconds the dishwasher stops making any noise and beeps once. When I open the door the green on/off light intermittently flashes. Any thoughts what the problem is please?


... Dishwashers

Same question: When starting my Bauknecht GSF 5481 dishwasher the problem is that I start the dishwasher and after some time - when finished or close to finish - it changes to rinsing and the light on top of the START buton start to blink and I cant change the program. What to do?


... Bauknecht 24 in. GSF8971 Built-in Dishwasher

Just installed Hotpoint Dishwasher model LFT 114 uk loaded, program selected tablet in, shut door the machine beeps, then few mins later beebs again. when open the first 2 program lights are flashing. what does this mean but as not washed


I'm having exactly the same problem, was this ever resolved? ... Hotpoint Dishwashers

I have an Electrolux Dishlex DX303 Dishwasher. Recently it has been stopping early in the cycle and the display shows -10. The selected program is flashing. The cycle will restart by pressing the program button again but it no longers wash's right through the wash pe=rogram as it is meant to. I do not have the manual to trouble shoot and find out what this means. Your help would be appreciated. Regards Peter H


Hi peter,\012according to manual book -10 is not filling water fast enough.\012check inlet hose and valve, check pressure switch and pressure SW hose and clean sump filter which located bottom of tub that plastic strainer and stainless mesh clean the ... Dishwashers

After selecting a program, the dishwasher beeps for a while and the 3 buttons on the left flash too. Program wont start, water wont fill and nothing happens. THe lights keep flashing but the beeps stop for about 30 secon ds then start again. Help me Please.


Basically the dishwasher is telling you there is a fault - Not so useful I know! Plug out the machine and leave it for five minutes and see will it reset. If that does not work, you will need to reset it manually. To do this consult the manual. If yo ... Hotpoint 18 in. DC28 Slim-Line Built-in Dishwasher

Hello. I was given a dishwasher, whirlpool ADP 755. I've had it about a year and finally got it plumbed in yesterday, so excited! Not having ever had a dishwasher before, i'm uncertain what to do and i cant find a manual online. I tried putting some cups in it and running it on all the different settings on the dial but each time the cups are still dirty. The machine is steamy so looks like hot water is passing through, but its clicking through all the programs very quickly and leaving stuff dir


... Dishwashers

The dishwasher is flashing error 20. The wash cycle begins to work but after a few minutes the wash cycle will stop and the light flashes on the program selected. We have tried turning the dishwasher off from the switch to no avail. Please advise us on what we can do to fix this.


... AEG 24 in. Favorit 3A Free-standing Dishwasher

I have a kenwood kdw12st3a dishwasher (just out of warranty grrr). When turning on I am unable to select a programme. It beeps and shows "---" but nothing happens when selecting the program button. I have checked the door catch, seems fine. Any ideas please?


... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a Diplomat ADP 8352 Dishwasher which has stopped working - The on/off button works and "S" light illuminates but I cannot select a wash program or delayed time program - Any suggestions ?


Why does the s button stay on for? ... Hotpoint 18 in. DC28 Slim-Line Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1859 seconds