Having problems with your Dishwashers ?

Kenmore dishwasher model 665 16872000 bad heating element

\015 No high heat, dishes are wet at finish\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore dishwasher model 665 16872000 bad heating element


... Dishwashers

I need a heating element (i think) for my whirlpool quiet partner 1 dish washer, but i need the model number and I dont have it with me, do you know the part number for the heating element that I need or do I have to know the model of my dishwasher? it started with DU and was either DU1100 something or DU1050 something?


Your Whirlpool Quiet Partner 1 should have its model number inside along the left side. Mine is DU1010XTXT1. Your heater part is original Manufacture # W10518394. Can be purchased for about $38.00 at \012 ... Whirlpool Dishwashers

Kenmore Dishwasher Model 665.15912001 Heating element doesn't seem to be heating. Wash cycles are loooooong and the drying cycle doesn't exist. Easy fix or buy a new dishwasher? I haven't tested anything yet. Should I start with the thermostat or the element itself?


Hi. i would test the element first. this will be the likely issue.First, open the doorand look into the tub and locate the heating element (if it is covered, remove the lower dish rack and cover). The heating element has two termina ... Dishwashers

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

Kenmore Model 17039 Undercounter dishwasher. I replaced the flaking heating element yesterday. Now in the middle of the cycle, the dishwasher stops and the clean led blinks. The cycle will not complete.


... Kenmore 24 in. 17039 Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Kenmore ultra wash 665 dishwasher heating element melted down in one corner


... Dishwashers

We have an older Champios Model U-HB dishwasher and the heating element has gone bad. The picture in the manual I downloaded us J-shaped and the one in my unit is U shaped. Any info you can give me would be appreciated. Thank you in advance for your assistance.


... Dishwashers

Model #66516352301 replace heating element - Kenmore Dishwashers


\012\012Hi,Check\012your heating element.. \012\012A\012bad heating element causes many problems in dishwashers...Dishwasher\012Problems The ... Kenmore Dishwashers

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

My heating element isn't working on my kenmore dishwasher. Any suggestions? model # 13429


The # you gave is the catalog number. Please provide the model number, which is in the format abc.defghi . . . . How do you know the heating element is not working? Could there be another problem causing the element not to operate? ... Kenmore Dishwashers

I have a Kenmore Elite dishwasher, model number: 665.17263. The clean green light is blinking and unit work work. I had this problem before and the service guy showed me how to press the buttons in a certain sequence which fixed the problem. It was the heating element.


All I had to do was to press the heatdry and normal wash buttons until all the lights went on. This happened before...Gingko was fantastic!! ... Dishwashers

Dear sirs, I own a Kenmore dishwasher Model # 665.17039400. The clean light flashes 7 times and then repeats. It will not run, only the drain button will work. I changed the heating element from advise on another forum. This did not resolve the issue. Please advise promptly as my wife is going crazy without this appliance. Regards, R. Carmikel


... Kenmore Dishwashers

The water does not run into the dishwasher, though the heating element works, and it goes through the cycle. The dishes are not getting washed. Also the ON light is not working. model number Kenmore 6651676569.


Hi,Here is a tip the will elaborate on your problem more, but the bottom line is that you need to replace that fill valve...Dishwasher ... Dishwashers

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

Model SHE68P02UC/60 There does not appear to be a drying heating element in this dishwasher or did we miss connecting something up during the installation? Unsatisfactory drying on both "normal" cycle and "auto wash" cycle.Drying agent is in machine. What is "condensation drying"? Is this just blowing cool air through the machine and out through the vent? If so it is unsat. How to get the machine to actually DRY the dishes? I'm going to be very disappointed and out over $1,000.00


I am assuming you have the dishwasher connected to the hot water tap which can give water at about 40deg c (120deg F).\015\012\015\012The dishwasher uses steam from the water (after heating it further). So if the inlet water temperature i ... Bosch Dishwashers

Kenmore dishwasher model 363.1410691, approximately 18 yrs old... Wash cycle was on, unlocked and opened door to add silverware, shut and locked the door, but water did not (and will not) come back on. Appears heating element and timer still works...any ideas?


Check your water valve. if know water goes in normally that is the culprit. disconnect the wires and ohms it out with a ohms it out. if this works then you can help me by sending me a 4 thumbs up post thanks! ... Kenmore Dishwashers

Kenmore ultra wash 665 dishwasher heating element melted down in one corner


... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Kenmore dishwasher spray arm too low, hits heat element bracket


There is a picture of the inside of what I believe is your dishwasher. It is not great but might give you some idea of what might be missing. http://www.bobgolds.com/dishwasher/home.htm ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a GE Profile Dishwasher, Model# PDW7880J03SS that doesnt dry the dishes. I pulled out the dishwasher and checked the heating element for continuity with my ohm meter and got a closed circuit reading. I tested the voltage going to the heating element and got a 124V reading. However the dishes are still soaking wet after the drying cycle. What am i missing, what else could be wrong with the machine that the dishes won't dry at all?


Hi\015\012\015\012Check if the dishwasher is draining and filling properly is water temperature. Water temperature should be between 120 and 140 F. If water is not hot enough then heating element has gone bad, to check the element you'll ... Dishwashers

Westinghouse Dishwasher Model SB907W5*08 the dishes are not getting cleaned & it appears that it is not heating as i bought a bottle of dishwasher cleaner & the dishwasher is supposed to heat up enough to dissolve the lid off the cleaner to let the fluid out. after putting the cleaner through a cycle the cleaner lid was still there. i think this must mean that the heating element is broken? this is out of warranty & can't remember how much it cost us so don't know whether better off gettin


Hi\015\012If you are observing that the dishes are not clean, then you'll need to follow certain steps to be sure where exactly the issue. First thing to check for is the detergent cup and spray arms. Check if the dishwasher's spray arms are w ... Westinghouse 24 in. MDP531 RF Free-standing Dishwasher

We have a kenmore ultra wash dishwasher. i am unsure of the model number. i believe it was bought in 2001. the NO HEAT DRY button was blinking, so we replace some panel under the door. now the QUICK RINCE light is blinking. i tried the sequesce of WATER HEAT, NO HEAT DR, WATER HEAT, NO HEAT DRY, but that did not help. any other suggestions?? we have a family of 4, and it STINKS not having a dishwasher! litterally sometimes : )


... Kenmore 15129 Built-in Dishwasher

Bosch dishwasher shx46b02uc has stopped drying. Per online comments, they seem to point to either a corroded wire or a bad heating element. We've replaced the heating element and all the wires looks fine. All other functions work - just not the heat. Open to suggestions.


Hello,Welcome to FixYa.Based on your description ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2401 seconds