Having problems with your Dishwashers ?

Hi, When I turn on my dishwasher, it fills as normal with water but is not pumping into the upper spray arm. the spray arms are not clogged, I have checked them. Anyway, I always rinse the dishes under the tap before placing them in the dishwasher. I have to switch the machine on/off several times then the pump starts at full force.Occasionally it goes through a complete cycle without havig to switch on/off. It's a Siemens Lady model, E-NR SN53300GB/08, FD 7201 058479. The dishwasher is used


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, When I turn on my dishwasher, it fills as normal with water but is not pumping into the upper spray arm. the spray arms are not clogged, I have checked them. Anyway, I always rinse the dishes under the tap before placing them in the dishwasher. I have to switch the machine on/off several times then the pump starts at full force.Occasionally it goes through a complete cycle without havig to switch on/off. It's a Siemens Lady model, E-NR SN53300GB/08, FD 7201 058479. The dishwasher is used


... Dishwashers

Dishwasher Our dishwasher is not washing the dishes. The water go in and it goes through the complete cycle and dumps the powder in but the water never gets above the dishes or even to the soap holder. The powder is a dry pile below the dispenser. It seems that the spray arm doesn't extend or spray water over the dishes.


I have a kenmore dishwasher (about 10 year old) it won't turn on. It just buzzed when set to wash. What can I do? ... Dishwashers

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

Won't Stop My dishwasher has only been used about four times but when I switch it on, it will go on an on for hours and hours until eventually we just have to switch it off. It doesn't dry the dishes just continously sprays water on them. The timer runs down but then just goes back up and starts again as though it keeps repeating the cycle.


If your dishwasher's cycle times are too long, check these:Water pre-heatingCycle not completingWater pre-heatingYour dishwasher may pre-heat the water. If so, and if the water entering the dishwasher is cool, the ... Neff 24 in. S5456 Built-in Dishwasher

My LG dishwasher LD-2040WH washed and as soon as the element goes on it switches off by itself. I put it on the gentle cycle and then it switch off and now there is nothing going on it is completely dead what can the fault be????


See the w. diagram for test1) Test the switch door for defective, this switch can be open or defective and can be open the starting relais and turning off the main motor.2) Timer: test for defective, clean contact, repair wires loose, bro ... Whirlpool 24 in. DU940QWD Built-in Dishwasher

I have a Bosch SGS66E02GB/45 that no longer completes a wash cycle. On "Auto 50C" time counts down from 2:58 to about 1:40 then goes back to the beginnnig and repeats. Spray arms are moving, it fills and drains, detergent is dispensed. I have checked the inlet and outlet pipes, the impellor and non-return-valve in the sump, checked the matrix is clear, checked to anti-flood float and switch and replaced the relays on the PCB. Selecting a rinse cycle will complete. Dishes are warm and wet rather


... Bosch Dishwashers

Hobart conveyor dishwasher model crs-66 serial#286458 2o8-3ph machine is 38 yrs. old. pilot lite would not stay on. changed thermoule coup. when switched to on everything goes off. this pilot valve is completely seperate from main gas valve.


I'm a hobart tech,The valve your talking about is the saftey valve.Normally if i serviced your dishwasher i would replace both valves just because how old it is.But in most cases the saftey valve goes bad.The coil on the valve is weak and tends to dr ... Hobart Dishwashers

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Smeg df612sdx Until last week I enjoyed several years faultless service from my SMEG Stainless Steel dishwasher, with the exception of needing to replace 2 x spray arms. The unit has now stopped working altogether. Despite powering up several times, I continue to get both the start/pause and selection programs buttons constantly flash (green lights) when the unit is switched on; previously this only occurred once the wash cycle was complete. Any thoughts would be most appreciated. Thank you


... Dishwashers

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor. ... Whirlpool GU2400XTP Built-in Dishwasher

There is a pool at the bootom of my dishwasher when the wash cycle is completed. When doing "Rinse Only", I could hear something come on immediately following the rinse but nothing seemed to happen. I pulled the Dishwasher out and the drain tube is set up so that it immediately goes upward a few feet before it eventualy goes back down to the drain. I noticed that there is water in the tube right next to the Dishwasher before it makes that climb. I'm wondering what all this means...


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012 ... GE GLD5800L Dishwasher

Bosch srs43c12gb/14 classixx dishwasher spray arms not spinning. The dishwasher goes through normal cycle but the spray arms are not spinning, I have cleaned them and the filter inside the machine and the one on the water hose, still not spinning. the machine is about 4 years old.


... Bosch Dishwashers

Hi got a baumatic dishwasher bkd62ss.1 model, it gets half way between the last cycle and cuts out and blows the circut board switch, can turn dial and wee bit and re switch circut board and away it goes again. what would be causing this problem. had dishwash for about 3-4 years? thanks


... Baumatic Dishwashers

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

I have an LG dishwasher lds5811ww -- for about 1.5 years. Purchased it at Best Buy. The soap dispenser is not emptying completely anymore. The upper rack is in its uppermost position. I suspect that the top two spray bars are not turning around because they have not changed positions when I suddenly open the dishwasher while in operation. The spray nozzles do not appear clogged. Any suggestions?


If your dishwasher is cleaning poorly, check these:\015\012\015\012Water-inlet valve\015\012Internal filters\015\012Drain valve\015\012Spray arms\015\012Water temperature\015\012Detergent cup\015\012Water-inlet valve Most cleaning problems are ... LG Dishwashers

Detergent sticks in main wash compartment. We use cascade complete with bleach (hydroclean action). When this problem started, I switched to cascade complete (liquid) and still same thing happens. The dishwasher is only 3 1/2 yrs old. Have used cascade complete since day one. Only difference is that this one is the one with the bleach. Could this be the prob? We have noticed that it is thicker that just the cascade complete. But thought the liquid would of fixed that prob. Agh frustrated. We hav


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Indesit dishwasher needs to have the micro switch aquastop replaced but not sure which wire goes on which contact on the switch. Two wires , one pink and one brown.


... Indesit 24 in. DI67 Free-standing Dishwasher

I just installed a new Kitchenaid dishwasher (Model KUDE60FVSS3). After filling with soap, closing the door and starting the machine, it fills with water, waits a couple of minutes and then I can hear low humming noices coming from down below. After opening the door it appears that neither spray arm has turned as if to wash. This dishwasher was purchased new a few years ago and kept in storage as our basement was being finished. This dishwasher has never completed one cycle. Any and all inf


If you have a garbage disposal, there is a plug in the dishwasher that has to be removed for the washer to drain. ... KitchenAid KUDE60FVSS 24 in Builtin Dishwasher

I have a GE potscrubber Dishwasher Model # GSD3630ZZ3WW it has been leaking from the bottom for about a week. I took the bottom off tonight and ran the dishwasher so that I could see where it is leaking from. It is not a hose but the leak seems to be coming from the back of the motor or pump fan where it goes into that plastic housing that attaches to the bottom of the dishwasher seems to be leaking in the very center of that housing where the motor shaft enters the housing. Water is just spray


... Dishwashers

My Bosch dishwasher Model SHE44C02UC just went completley dead while washing. My wife and I were in the living room and heard a ''pop'' and went to investigate. We discovered the dishwasher was completely dead with no lights on at all. The on/off switch does not work. I checked the breaker and it is okay. Also the disposal is also on this circuit and it still works so I know the circuit is okay. There is still water in the bottom of the dishwasher - no suds - so it may have been in a rinse cycle


Well done on confirming that the outlet is not the problem. This problem will not be able to fixed by the owner and a service call is the next step. (unless you want to dig into the problem, which could easily be a failed pump motor which took out t ... Bosch Dishwashers

Dishwasher Water is not going through upper and lower spray arms. Checked overfill protector switch, inlet valve, inlet valve screen, pump blades move freely, Pumb motor is working , Water enters into machine but does not go throught spray arms. Water heats up, Machine will go through all cycles but without water going through spray arms. 650 / 690 series gldb656jso


... Dishwashers

Leaking dishwasher The dishwasher leaks a stream of water at the base -bottom left corner whenever it goes into the final rinse cycle. It does not leak when it is in the wash mode. This leak just seemed to develop suddenly. There was no build up -ie a small stream of water. I just noticed a big puddle on the floor one day after dishwasher had completed its cycle water leak in the left side ,bottom ,husband states a small drip,drip and we do not know what to do or replace. No water standing


I just had this same problem and it was caused by a small plastic seal on the bottom of the door. My friend owns an appliance store and he said this is a common problem for this model of dishwasher. The part was $68 and the labor was $60. I could ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Asko Dishwasher starts the cycle by pumping out as it should. But does not stop pumping nor advances. If I click it forward manually it starts to fill and then before overfilling goes into pump out without washing then just repeats this. Pressure switch tubes and air trap chambers are clean and no leak to trip spill switch. I'm guessing It is either the timer or faulty pressure switch any clues ???


If has "mother board" then water could have got in.\015\012\015\012Here Asko is low cost make so check cost before serviceman calls & charges & charges and so on. ... Asko D1706 Built-in Dishwasher

Removed lower spray arm of KitchenAid dishwasher and need to reinstall it. This installs over a spray arm nut that is a split ring. The nut goes over the outlet pump. I cannot get the nut to go over the outlet pump and then go inside the spray arm, which is 1/4-inch smaller in diameter.


... KitchenAid KUDS24SE Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2139 seconds