Having problems with your Dishwashers ?

Danby DDW611WLED E1 error message flashes after it's been running for less then 5 mins. Water was seemingly flowing in & draining out just fine. The tap is turned on all the way & we've double checked all the connections. Anybody know how to help us resolve this issue? I was so happy not to be the "dishwasher" anymore


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Danby DDW611WLED E1 error message flashes after it's been running for less then 5 mins. Water was seemingly flowing in & draining out just fine. The tap is turned on all the way & we've double checked all the connections. Anybody know how to help us resolve this issue? I was so happy not to be the "dishwasher" anymore


... Dishwashers

Dishwasher is just less than 1 year old. it doesn't respond to attempts to turn on. I turned off the power at the box and back on after 10 minutes. it worked. then the same problem returned. now it wont turn on at all. I checked all the connections I could and they seem fine. I know it is getting power. My guess is that something is wrong with the computer system. any ideas?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Maytag 24 in. MDBH950AW Built-in Dishwasher

Leaky Tub our dishwasher was leaking quite a bit. i checked all the hoses, and connections, it turns out that there were two screws from underneath protruding into the tub, near the rear on either side. If any one knows if the tub could be fixed or replaced could you let me know? Also if this was a manufacturing problem shouldn't sears be responsible?


Are you sure that water leaking out from these two points.\015\012If this is the reason for the leaking, it's absolutely a manufacturing problem and you should forward your problem to Sears to take care fot it !!\015\012Generally,this problem could b ... Kenmore 24 in. 17019 Built-in Dishwasher

Due to the my Indesit IDL 530 dishwasher not draining properly, I turned it onto it's left side, removed the base plate and pump and checked for blockages in the pump and associated hoses, which were all clear. However in re-assembling it I have forgotten which way round to connect the twin wire plug to the base plate. I cannot find a relevant wiring diagram online and therefore cannot tell which is the correct way around. I then guessed and re-assembled it anyway, and as you might have g


Hi.There is more than one wire going from control board to the tub. If the connector can be plugged either way without forcing it, then usually does not make any difference the way you plug this determined connector. It will be usef ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My Whirlpool DP1040XTXQ portable dishwasher will not turn on. I've checked the plug, outlet, breaker, etc... I know there is a way to reset the keypad by holding down a couple of buttons at the same time, but I cant remember the right combination or how I learned it in the first place. It's not in the user's manual.


... Whirlpool DP1040XTX Portable Dishwasher

Old dishwasher had power, I connected a new dishwasher and it doesn't work. I double checked and made sure I turned the power back on at the breaker box.


Hello, have you tried plugging something into the socket the dishwasher is plugged into.\015\012\015\012Hope this helps. ... Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

I have a Miele G 892 SCU PLUS Dishwasher. I have clean the filters, check the pump and could turn the impeller both ways. I turn on the dishwasher and it will pump out any water and fill then heat the


... Miele Dishwashers

My AEG Favorit 35085 VI dishwasher is not working properly. The manual says to turn water tap off and on but I don't know where it is. O assume they mean a tap to the machine and not to the proper


... AEG Dishwashers

Just installed an estate TUD6710S and on the first run it is leaking from the check valve. It is leaking from the pump side of the valve. There isn't any leak where I have the drain connected. I do not have a garbage disposal, so, there's not a problem there. The drain connection is 20" from the sub-floor... don't know what else to check.


... Estate TUD6710 Built-in Dishwasher

Dishwasher sounds as if it starts cycle, then stops, bleeps, and Fat and prewash lights come on. Manual says to turn off machine, turn off tap, wait 30 seconds and turn it all back on, but it doesn't make any difference. Manual says 'If the above does not solve the problem, check that the water feed pipe is not blocked' however, it doesn't say where this is, or how to do it. Please help!


Hi.You need to check the water inlet hose, that is the hose connected to house water faucet at the back of the dishwasher.Checck for blockage in the hose and ensure that the inlet hose is not blocked or kinked.If t ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Bosch Exxcel Dishwasher (Enr SMS53E12GB/01 FD 9002) bought in July 2010. Error code 15 and "Check Water Supply" light on at same time. Have checked in-line filter in tap connection and all clear, water pressure OK, no kinks/twists in supply hose. Any help would be greatly appreciated - I'll have to call Customer Service in the end as it's outside of my problem-solving ability, but would like to check whether there's a known reset or fix I can try before I call.


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

My ASKO D1996 Dishwasher will not turn on, checked the power and it is running, but no lights or anything turns on. I don't have the water connected to the machine, could this be the problem?


NO, you should get light actions even if the water was not connected. this is a main control issue. there is a control board kit available for your unit. you will need to replace this damaged control in this case. the logic sector is damaged. ... Dishwashers

AFTER A BRIEF POWER OUTAGE DUE TO ELECTRICAL STORM THE F1 CODE FLASHES AND PUMP RUNS CONTINUOUSLY. TURNING POWER OFF ONLY STOPS IT FOR SEVERAL SECONDS. TURNING OFF POWER TO DW AND BACK ON DOES NOT RESET. I HAVE REMOVED THE BOTTOM DRAWER AND CHECKED FOR WATER, BUT UNIT IS DRY. IS THERE ANOTHER WAY TO RESET THE SWITCH?


Hi there,The f1 fault is cased by a leak on the dishwasher.It is activated when water gets to a dangerous level in the base of the appliance near to the PCB.The main reason this happens is putting cups on the drop down s ... Dishwashers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

After turning the dishwasher on, it went through half the wash cycle then completely powered off. Cannot be turned back on. Checked all connections, circuit breaker, etc. Thanks for any help, Michael


It is possible the thermal protection device has tripped. This is at the base of the dishwasher and is part of the thermostat and will look ... Siemens 24 in. SL84A305UC Built-in Dishwasher

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

Hi there, Just moved in to a new place and loaded up this dishwasher. First set it to "normal wash", dry "off", "start". Made noises but after a couple of minutes I heard no water and think I smelled the beginning of something overheating. Think I checked to see if the water was turned on under the sink (turned all the way to the right?). Still nothing but noise. What do you think? Lorraine


Lorraine.. It sounds like the water valve under the washer is stuck or maybe partially shorted. It is a solenoid coil activated shut off valve. The coil may be overheating, and valve not opening.. so motor is running dry. \012If you want to ta ... GE Nautilus 24" Built-in Dishwasher

Hi, we have a Bosch Exxcel dishwasher which mid way through a cycle a button saying Check Water came on. we turned the machine off and opened the door and found loads of water in the bottom. my husband then scooped all the water out and cleaned filter in the bottom, where we did find some bits of plastic from the kids yoghurt pots, and took the water hose off the back and checked for blockages, which there was none. the water is certainly coming from the water pipe through the hose as we tested


Check your water level sensor. And also check to make sure that your pump is working correctly. It sounds like a couple of different things that need to be addressed. First check the water level sensor. It is a tube that is located from the back of t ... Bosch 24 in. SHU43 Built-in Dishwasher

Hello everybody, I hope that you gona a give me some tips for repairing my dishwasher mashine. A few days ago, the error F2 appears on my dishwasher machine (Baucknecht GSI 5894) I checked the pump for the waste water is ok. the tap water is not taking in,I checked the hoses they are ok as well I turned off and on and same time pressed the button reset and choosing the programm on the dishwasher few seconds trying to start and again apperas F2 . Hopefully someone can help me. Best regard


Possible the inlet valve has given up and is not allowing water in.\012Also possible there is a slight leak enough to shut the water off (safety feature) - Check underneath for a float mechanism and any water there. ... Bauknecht Dishwashers

Leak where right angle cast brass(?) piece meets bottom of Hobart dishwasher. The bottom of this piece is connected to the drainpipe.I don't know if it is part of the dishwasher or part of the drain. Either way, I want to know how to fix it.


Vent Hood drain ? ... Hobart AM14-253 Free-standing Dishwasher

Inlet Water Hi There,Motor etc runs when we turn it on but absolutely no water comes in.I have checked the inlet hose at the tap end,and the tap,and that is all OK.


Do you have voltage to the water valve if no then check the float switch if switch is good problen is in the control\015\012\015\012if you check the water valve and have voltage to the 2 wires on the valve ac voltage btw then the valve ... Dishwashers

Kitchenaid model KUDIO1ILBL6 The lights for Heavy Cycle ,Normal Cycle and Cancel blinking at the sametime constantly. The tech sheet is missing and the unit is appox. 5years old.have shut power down for 5 minutes .When power turn back on only the Heavy Cycle light blinks costantly. Have Ohmed out the door switches and check adjustment OK. Checked board strips and plugs for good clean and tight connections OK. Thanks


Hi, You need to reset the unit by pushing the buttons. Push the heated wash/heated dry a few times. All the lights will light up and the dishwasher will continue its . Let ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Bosch shv55mo3gb Keeps stopping during cycle, when open door the little tap light is on meaning trouble with water, checked supply vavle is on, checked filters and no kinks in hose, if i turn the water supply valve on and off then sometimes you can here the water flow through and it will work again, onlt 13 months old??


Use this link then click on insruction manual download type in the model number remember 0 is a number.I know that sounds condesending but i forgot. I used the manual with the ending aus.\015\012\015\012 ... Bosch 24 in. SHV55M03GB Built-In Dishwasher

Hi, how do i install my dishwasher....i dont know where to connect the water supply pipe to as i dont seem to have a tap under the sink for it to be connected to, can anyone help please.


You'll have to tap into the hot water supply for the sink to get a connection for the dishwasher. This is a moderatley difficult plumbing task. If you don't have plumbing experience, it's probably best to call a plumber.\015\012\015\012 ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1338 seconds