Having problems with your Dishwashers ?

My Frigidere dishwasher 400 Series AquaSurge w/Speed Clean has an error light Er S It indicates low rinse aid but I have filled the dispenser..I can't get the start/cancel button to work or to mov

\015 I wasn't running the dishwasher when the Er S light started blinking....\012Does this information help in determining the problem?\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Frigidere dishwasher 400 Series AquaSurge w/Speed Clean has an error light Er S It indicates low rinse aid but I have filled the dispenser..I can't get the start/cancel button to work or to mov


... Dishwashers

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

Maytag MDBTT60AB front panel not working, weve had troble in past getting buttons to work now there is nothing at all no lights and we cant get it to start.


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

I have a frigidaire series 4000 model FDB4315LFS1 and the display will show PF if i unplug it for 5 min and plug it back in however i cant get the control buttons to work. is shows no sign of life. holding buttons for 3 secs wont work either.


Hi\015\012\015\012PF error means power\015\012failure, if reset wont work then let it remain unplugged for 15 minutes and in\015\012this time take a hair blower and blow air on the control panel as this will\015\012blow away the moi ... Frigidaire Dishwashers

Have a lg model lds 5811st model dish washer for a little over 2 years and had the le error button .called technican replaced the motor now 4 weeks later the same error button.and the cancel button wont release the water standing in the bottom.also cant get repair man to garanty his work or parts.


Take off the door cover and you will find the wires melted into a black blown in insulation. Carefully free the wires and run a quick check to see if any of the wires are broken. If they are cut them and splice them back together. It takes a while ... LG LDF6810 Built-in Dishwasher

So, it was working fine for 4 years. Then last week it started getting louder after the initial fill cycle. Now, all it does is fill the bottom with water, clicks (where the motor used to kick in), then just hums. Nothing happens, but when I hit the cancel button, it empties the water from the bottom. Any ideas?


Your spray pump motor has become blocked or ceased - do you have the tools and skill to dis-assemble the machine? ... Whirlpool GU2455XTS Built-in Dishwasher

I have a bosch SHV43A03GB dishwasher. It has a problem when it cut out water flow in. the guy who repairs it seem s only to have to push a button or switch under the machine to get it to work again, cant find switch/ button- please help!


Programmer not working ... Bosch 24 in. SHU53 Built-in Dishwasher

Normal wash cycle- tub fills (?), then comes a loud hummmm and nothing happens. I noticed water level didn't reach heater coil and added water until limiter switch clicked. Still just a loud hummmm. Machine was well into its regular cycle when this first occurred, but now, won't even get past initial fill. Pushing the "Cancel/drain" button activates motor and pump: they work fine.


You are an expert enough reading this. But with a terrible complicated dishwasher. First clear the waterlevel problem.\015\012Rest is a result. You do not need me, join us. Next time buy something more plain. ... Dishwashers

I have a Kitchen Aid dishwasher. IC Series. Model # KUDN230YWH. The dishwaser fills and runs but it does not cycle past that. It will run until we shut it off. I can hold the button in and it will click and to get it to the drain cycle and it will drain but it will not do it on its own. It just fills and runs. Thats it. Thanks


Hi\015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing that should be checked is the Timer and then the\015\012heating element. Timers don't often ... KitchenAid 24 in. KUDP02SRSS Stainless Steel Built-in Dishwasher

FDW80 the error code DEMO is on permanently and won't let any program run. the refill salt and rinse aid are flashing but they have been filled already. I have tried holding the on/off button and reset button down together but its not working, and i've tried switching it off at the plug and leaving it for a while, but nothing.


When the support engineer says press the 'on/off' button and 'start/reset' down together, press very hard. Press hard for 5-6 seconds and a the wording 'demo off' appears for a split second, then resets its self ready for use. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Have no water getting to my dishwasher i have filled salt and rinse aid as the lights were on on the last time it worked tryed all the advice what can i try next


No water ! - check the flow first at your tap end or the at machine entry gland nut. Clean the filter by pulling it out. It will be small in size. If inlet valve not getting opened also will lead to this problem.For trying oth ... Dishwashers

I have a Dishlex Global 300 dishwasher that stopped working mid-cycle. I had to sponge out all the water. Now none of the buttons do anything and none of the lights come on. When I turn it on at the power outlet it gives a single beep, but I cant get it to do anything else. I've opened it up and there is no water or dampness anywhere inside. Any ideas?


It is your control board inside your dishwasher. ... Dishwashers

My Kenmore ultra wash dishwasher fills with a little bit of water but does not spray water and does not proceed through the wash cycle. Any advice? We had problems yesterday with blinking lights and not able to get anything to work except the drain. then we followed a sequence of pushing buttons and it solved the first problem.


The spray arm rotates based on the water pressure coming out of them. If no water pressure, then no rotation. You probably have a clog on the intake hose. You can pull out the dishwasher, tip it forward so you can get to the bottom and then rem ... Kenmore Dishwashers

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

I have a whirpool quite partner 2 and my water froze but has sence been fixed but now i cant get water in my dishwasher everything eles works but it wont fill


Check your float swich inside front of dishwasher lift it then drop it ..listen for a click...onthejob ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

MY KITCHEN AID DISHWASHER MODEL #KUDS25SH CHIKD LOCK IS ON AND WONT GET CLEARED. I TRIED HOLDING THE ENERGY SAVER DRY BUTTON FOR FOUR SECONDS AS SAID IN THE TROUBLESHOOTING SECTION BUT DOES NOT CLEAR. PLEASE HELP I CANT AFFORD A NEW DISHWASHE


Try turning off the breaker to the Dishwasher...See if it resets ...Good luck.,.. ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

KUDG25SHBT1 Kitchen Aid dishwasher child lock is on and cant get it off. Pressed and held the start button and now the child lock light is blinking but dont know what to do next?? Please help!! Lexi


... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Dishwasher is locked out. Toddles was playing with buttons and now cant get it to work. I know there's a way this can be fixed for Ive had this problem before and got it fixed very quickly w/o a problem.


Press and hold the lock key for 3 seconds. The button has a picture of a padlock on it. ... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

I HAVE A BRAND NEW BOSCH MOD.SHE4AM12U DISH WASHER IT START TO FILL WITH WATER,THEN STOP AND NOTHING ELSE HAPPENS,CANT GET IT TO START THE WASH CYCLE.IS THERE A REPAIR MANUAL OR SCHEMATICS THAT I CAN OBTAIN TO TRY AND TROUBLE SHOOT THIS UNIT,I WORK WITH ELECTRICAL APPLIANCES AND I AM QUITE KNOWLEDGEABLE WITH TROUBLE SHOOTING.THANKS


... Bosch SHE4AM12UC Dishwasher

Lights work, dishwasher works but "start" button won't start it. I can get it to work sometimes by hitting a few of the buttons back and forth. Otherwise, I can't get it to start.


... GE 24 in. Monogram ZBD6880KSS Stainless Steel Built-in Dishwasher

Hi, We have a Smeg ST 663 dishwasher that does work. However, sometimes when you want to use it and turn the power button on it beeps twice with the red light flashing and you can't get it to work or change the settings. Sometimes if we leave it for a while and try it again later it will work, but it is annoying as sometimes it won't want to work for ages and we really want our dishes cleaned! The dishwasher doesn't have many buttons on it (a power button, cycle selection button and 1/2 load


Hi,\015\012\015\012Turn machine on and press and hold the programme select button till the light goes out about 5-7 seconds see if this resets it if it does start a cycle and see what happens.Otherwise the pcb as its not responding to an ... Smeg Dishwashers

I have a Kitchenaid KUDIO1DL white dishwasher which is a few years old now but has worked great since I bought it. Today it has the lean light flashing and will not turn on. there is power, and the drain button seems to work, but I can not get the cycles to come on. When I press the start button, I just get two dash lines and then the unit turns off. Thanks


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

After the last wash I noticed the bottom of my dishwasher (Whirlpool quiet partner 2) was filled with water. After unloading the dishes I closed the dishwasher and pushed the Cancel/Drain button but the button didn't work. None of the buttons work. It's as if the dishwasher became unplugged. I looked at the nearest outlet beneath the sink, but did not find anything unplugged. I wasn't able to drag the dishwasher out of its area beneath the counter by myself and figured I better ask first be


1.Check the drain filter for clogging. 2. Check the drain hose. Remove carefully to avoid water spill.3. Check whether flows freely from the hose.4. Check the drain valve if possible for you. ... Dishwashers

I have a Bosch dishwasher (SMI5072), bought in 2005 second-hand but working OK. It has always been a little slow to get going, and I had initially thought the clockwork program dial was getting stuck. Then I concluded that it had something to do with the filling up process, and I thought it must be because the water was rather cold and paid no more attention to it. This has meant that it seemingly takes ages to get through a cycle. Yesterday I put it on, left it and got on with some work. An h


There is a screen inside your water inlet valve that may be clogged. You will need to see if you are getting power to the water inlet valve when the machine calls for water. If you have power replace the water inlet valve ( not uncommon in older Bosc ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1674 seconds