Having problems with your Dishwashers ?

I have a Triton Aspirante Topaz shower which I purchased 2 years ago. Just recently it has started to give me a problem. With the temperature control set normally to 43 the shower goes through its pre

\015 I have a Triton Aspirante Topaz shower. Just recently it has started to give a problem. With the temperature control set normally to 43 the shower goes through its preliminary function and as expected registers 43 with expected water temperature. However it does not remain this way as the temperature continues to rise (the noise within the shower unit increases) and the water increases and gets hotter until around\01246 the noise within the shower unit suddenly stops and the temperature and volume of water decreases. At a reading of approx 39 the temperature rises again towards 43. However there is no stability and within a few seconds the whole cyclic sequence begins again.\012\012Prior to the current problem the shower worked perfectly and was stable on the temperature set. It is still possible to shower during the cyclic changes but it is uncomfortable. Please note that the shower head is cleaned regularly and the Scale Trap and Inlet Filter have been checked and cleaned.\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Triton Aspirante Topaz shower which I purchased 2 years ago. Just recently it has started to give me a problem. With the temperature control set normally to 43 the shower goes through its pre


... Dishwashers

Problems with Danby DW1899WP. My husband and I ordered it from Wal-Mart online and picked it up yesterday. We've read through the manual several times, filled all the appropriate receptacles, plugged it in, hooked it up to the water, loaded it, set it, started it, and it doesn't work. It runs the pre-wash rinse for about five minutes before giving a series of beeps, draining the unit, and switching straight to the dry cycle without actually washing the dishes. Help!


... Dishwashers

Maytag Quiet Series 300 dishwasher leaves sediment on dishes (primarily glasses) after running the Autoclean cycle. We've taken it apart, cleaned spray arms, filters, float and replaced some seals, but still have problems. We use Cascade detergent and Jet-Dry (what was recommended when we bought the dishwasher). Our water temperature is 120 degrees (maximum setting we can have without having our tankless water heater modified), but this dishwasher problem was an issue with our old tank water hea


The problem is hard water. www.dishwasherfilter.com has a\012product to solve this problem once and for all. It filters the water going into\012your dishwasher and remov ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

The start/pause button beeps when pressed to start a program and the machine gives a beep in response and appears to start its initial sump emptying phase but stops within 1-2 secs. Have checked pump and found no problem but start time is so short that in cannot have sensed a problem in the pumping circuit. If I persist in holding the start/pause button in, it can be released after the initial sump emptying phase (2-3 mins) and phase 1 of the wash program goes to completion. At the end of the


Hi\015\012\015\012Ronald...the beep sound itself indicates an issue with the\015\012membrane switch (control panel) and it should be replaced. I believe that the\015\012pump and motor is fine as its just beeping and doing nothing else. Ho ... Smeg 24 in. DWI612 Built-in Dishwasher

Hi i dont know the model of the dishwasher.. but the controls are fairly staright forward... a little knob for temperatur control and an on/off button.. and a light that lights up green when dishwasher is switched on... now the problem is as happened recently, when you switch the washer on greenlight is on and washer can be heard doing something but after a minuit or so the washer stops and the green light flashes. open up the dishwasher no sign of water or that it has done anything at all... th


It sounds like your washer is not getting enough water to start. If your washing machine is filling too slowly or not at all, then you probably have a clogged screen on the back of your washer. To check this: \015\012\015\012 ... Whirlpool Dishwashers

I have a Type S9J1S - SE64A630GB dishwasher which is not progressing beyond draining. With power on it seems to be constantly draining. There are no lights displayed on the control panel strip, and I cannot force it to re-set. This suggests to me that it is an electrical control-panel problem. Any assistance gratefully received!


... Siemens 24 in. SE64A630GB Built-In Dishwasher

We have a GE profile dishwasher that will not drain. We have replaced the keypad control and control module and it still will not drain. When we put it in service mode, we can get it to drain that way but when it is taken out of service mode, it goes right back to the same problem.


Its the timer issue:--\015\012what the timer does is control the motor and drain valve. If the timer doesn't work properly, the water may not drain and you need to replace the timer. This problem is common. ... GE 24 in. Profile PDW7800 Built-in Dishwasher

I have an ADG7550 whirlpool dishwasher. Am experiencing a fault when placing on a normal 65 degree programme it starts to fill and then defaults to pre-rinse and the start button and light flash eleven times. Can you explain what type of fault this could be ? I have had a similar problem 12 months ago when it was described as a water pressure problem which again was in the winter and wonder if this is the same. I would add that if I re-set the start button by holding it down and then re-start


... Whirlpool Dishwashers

I have a ge profile pdw8200 dishwasher. it goes thru a patial cycle then shuts off. now i have no power to the control panel. could it be a problem with the control panel. if so are they expensive and difficult to replace?


... GE PDW8200NWW / PDW8200NBB Dishwasher

I am trying to remome the control panel on my Bosch SHU43 and having some difficulty. Can you give me some direction. My problem sounds familiar with your responce to constant running and no cleaning. The control panel does not seem to make contact with any solection when you depress the buttons. This is my reason for accessing this component. Thanks for any assistance Joe.


Hello Joseph, welcome to Fixya.\015\012\015\012\015\012I can provide you with a tech. guide, but you`ll need to post an email address for me to send it to.\015\012\015\012With the guide you can practically tear that dish ... Bosch 24 in. SHU43 Built-in Dishwasher

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


THE TECH WHO CAME TO FIX MY DISHWASHER FROM Y=THIS EXACT PROBLEM TOLD ME THAT IT IS CAUSED BY THE WATER THAT TAKES TOO MUCH TIME TO GET WARM, SO YOU HAVE TO MAKE SURE THE WATER IS NOT GOING TO BE COLD BEFORE YOU TURN THE DISHWASHER ON. AS TO FIXING I ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Humming noise i have a GE nautilus GSD2200 model which has not been used more than 4 years that is giving me trouble.  it's making a loud humming noise (the noise comes and goes, comes and goes) which seems to be coming from the motor area at the bottom of the unit.  I stopped it in the middle of the cycle, but the water seems to be stagnant at the bottom.  any suggestion on fixing the problem myself?


I have seen this SOOOOO many times in my 35+ years in the appliance repair industry.......it is very typical....here you are this is an answer I provided someone with the exact problem not to long ago..............This is a t ... GE Nautilus 24" Built-in Dishwasher

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


Hi there,\015\012\015\012your problem is intermittent and before you start replacing parts, i would recommend that you do these checks:\015\012\015\012unplug the dishwasher from the wall\015\012check the connection betwe ... Dishwashers

Our De Dietrich Microwave oven is not working for the past 1 week. Power supply is good, All timer control and other controls and working. When I adjust the settings and press the "start" button nothing happens. It is too costly to get it repaired. Please suggest a solution to solve this problem.


... De Dietrich 24 in. DVF120J Built-in Dishwasher

Maytag quiet series 200 model MD88750AWB Dishwasher doesn't work. Control panel only responds to the heavy wash button. When pressed it lights up along with three option lights. After about 10 seconds they go off. There is no mechanical response to the pushed button. There were no symptoms leading up to this problem. If you can give me a "head's up" about what to look for before I open up the control panel I would appreciate it. Thank You John


Hi\015\012\015\012\015\012\015\012\015\012\015\012If your dishwasher doesn't work at all, check these:\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is there power getting to the dishwasher? This can be difficu ... Dishwashers

I have a kenmore dishwasher model #655.1374 or 655.1384 which is only about a year old. I am having a problem with the controls. It will not allow me to use smartwash. The only control that can be used is quick rinse. I reset it by pushing Sani rinse and heated dry. All the lights come on and it seems to do a test. But after that still the same thing except if I push start resume it goes to normal wash which stays on a long time and periodically the cancel drain light comes on as well as the 4


... Dishwashers

We have a +11 year old Bosch SHU3006/UC/U06 that never leaves the wash cycle. We had to stop it during our last test run at 3 hours. Chat advise is suggesting a water temperature problem (I origionall thought the timer), suggesting that the cycle will not advance until it hits a set temperature (170 degrees). We checked and noticed that the water in the machine was only around 90 degrees during a wash cycle. We do not have exploded views or parts drawings, nor electrical schematics. I wou


Check continuity of the heating element to see if it is broken/open.\015\012\015\012The dishwasher prefers that the incoming water (water heater) be 120 degrees (F) ... Bosch SHU3036UC Dishwasher

Fisher & Pykal Dual Drawer Dishwasher. Suspect after young child played with control buttoms on top drawer the power won't come on. Bottom Drawer works perfectly. Have tried turning unit off at power socket but this has not fixed the problem. Is there a sequence of buttons I have to press to re-set or is there in fact a re-set button?


Press and hold the key or lock button for 5 sec or till you here a beep to unlock. Or till the light goes out above the lock button. You can get your manual here just find your dishwasher.\015\012\015\012 ... Fisher Dishwashers

SAFE has come up on the control panel, can you give me any idea as to the problem. The machine is a hobart ecomax chh50 and about 6 years old. Many thanks, Jon


... Hobart Dishwashers

My new (less than 1 year old) Kitchenaid fridge (the model with the freezer at the bottom) has recently started to freeze the vegetables. The temperature setting is still at 38 degrees so I am not sure what the problem might be.


Check the back of the vegetable bins to see if there is an opening that you can adjust. sometimes this slot type opening is in front or on the side and is there to adjust the amount of air/humidity ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

The eco light is flashing constantly on my Dishlex Global 300 dishwasher, it is making a noise like a pump is running continously, but the unit will not operate. Can you give me some possible faults and solutions. Regards Dave I have the same problem. The Eco light flashes and there is some sort of noise, not sure if it is a pump or a solenoid, but thats as far as it goes. A friend gave me the machine after aservice tech told him the main washer motor was gone. i have fitted a new motor, but


Its an overflow of water into the base of the machine.There is a float switch in the base of the machine in a small plastic dish.There is a metal cover with 2 small bolts that have to be removed to get to it.get the overflow c ... Dishwashers

MAYTAG MDB7600AWQ DIAGNOSTIC CHECK USING CONTROL BOARD AUTO AND MANUAL, ARE GIVING ME A HIGH CURRENT WASH MOTOR DIAGNOSIS.(NORMAL WASH FLASHING) THE BOARD ITSELF CHECKS OUT OK. ALL FUNCTIONS WORK AS THEY SHOULD.WASHER FILLS THEN ATTEMPTS TO RUN FOR (ABOUT 3 SECONDS) IT WILL DO THIS 3 TIMES THEN BOARD GOES BLANK. ALSO, THE WASHER WILL FILL WITH THE DOOR OPEN??? BUT WON'T ATTEMPT TO WASH. REPLACE WASH MOTOR?? THANKS lYNN


I would agree.. Here is a site for you to copy and paste in your address bar that I think will be helpful:http://home.howstuffworks.com/how-to-repair-a-washing-machine.htm/printable ... Maytag Dishwashers

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi


... Maytag Dishwashers

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0764 seconds