Having problems with your Dishwashers ?

Problem with non-starting Smeg DWI 410 dishwasher - does anyone have a solution?

\015 Hi - my dishwasher won't start or reset. Lights 2 & 4 on the display are lit, and light 5 is flashing. Smeg say that it is not a listed fault (but someone else on this site seems to have had the same problem in 2010). Does anyone know how to fix this?\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Problem with non-starting Smeg DWI 410 dishwasher - does anyone have a solution?


... Dishwashers

The Dishwasher PLD2850RDC2 will not start. The CL flashes, the type of cycle pressed on the key pad does respond, but nothing happens when START is pressed. Steps taken: -Door is clicked shut -Power breaker has been turned off and back on -All dishwasher moving parts have been moved by hand to ensure no obstructions are in the way. Best guess is the key pad is just non responsive. I hope there is an easy solution. Thank you.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a DWI 612C Smeg dishwasher I have an error code of the 2 right hand LED's flashing Have tried to reset the programmer (turn off, on then press program 4 times in 2 secs, wait 15 secs and turn off) This enables me to select a programme, but when the programme starts, after five mins it beeps and carries on making the draining pump noise and the programme never starts When I turn it off and back on I get the far 2 red lights flashing again Have looked for signs of blockages and can


... Smeg 24 in. DWI612 Built-in Dishwasher

My smeg dwi 710 dishwasher keeps flashing on the diplay panel and won't change to another wash selection. it wont close and wont start. the light is stuck on the heaviest wash selection and just keeps flashing on and off and on and off. i have tried turning it off, keeping buttons held down and nothing seems to work. there is nothing in the manual that says what the flashing means so i dont know how to fix it.


... Smeg Dishwashers

Hi, I have a smeg dwi 409c dishwasher and when the cycle starts, it will not switch off also the water does not heat up??? Any suggestions?


... Smeg DWI409C Slim-Line Built-in Dishwasher

I have a Smeg DWD1SSE dishwasher, that has decided to start and stop on it's own during the wash cycle. We have to restart it at least three times during the 30 min short wash, and it very rarely gets to finish a whole cycle. I have stripped it down to make sure that there is no moisture on the main PCB behind the buttons, which there isn't. I think it looks as though the control board is faulty. If anyone can help or back my thoughts up, I would be very great full. Thanks.


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

Hi, I have a SMEG SA8200X Dishwasher, which after the wash cycle starts and drains for a couple of times it sounds with continuous beep with both lights flashing. Could you please assist with a solution, or does this require a technician to reset/repair. Thanks Michael.


... Smeg Dishwashers

Smeg di612ca dishwasher does not start


... Smeg DWI614 Built-in Dishwasher

Hi I have a LG LD-2052 dishwasher. It gives me an E 0 error - the water does not pump out when I open the machine after a few minutes when started to wash and message of E 0 appears? Have cleaned an


... LG Dishwashers

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Dishwasher Problem My Kenmore Ultra Wash Dishwasher has a light which state "lock" on and I can't cut it off or start the washer..Does anyone know what is locked and how it got locked and how to unlock it and start the washer?


According to my ultra wash dishwasher you have to hold the no heat dry button for 4 seconds and that is how you lock and unlock the control panel ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

After starting my dishwasher ADG 9340/1 (any program) and after pumping evt. (rest)water , the machine won't take fresh water in and gives an acoustic alarm ! After opening the dishwasher , I can see that the "Start"-led is blinking in sequences of six blinks . Can you give me please, a possible cause and/or solution to this problem !


... Dishwashers

Smeg Dishwasher Hello I have a smeg dishwasher - built in, push button. It has stopped working - the program start and you hear it drain but that's as far as it gets, no water appears to be getting in. A couple of times the last 2 program buttons flash or the rinse light is on when we open it. let me know if you have any thoughts on this - I'd really appreciate it. thanks Diane


Replace the timer/control board ... Dishwashers

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Hi My dishwasher started washing by itself and it kept going nonstop for a few hours, I stopped it and realized the panel did not light up , I shut it off and waited a while before turning back on again and this time started draining. I'm unable to use the panel to reprogram the dishwasher because it doesn't light up, do you have any solutions? please help


... Viking DFUD042 Built-in Dishwasher

My dishwasher will not start when I push the start button only the green light flashes I checked every thing I could. I checked the manual for solutions found none. Its a kenmore dishwasher model no. 587.1619.


... Dishwashers

Aeg favorit 86070 vi fully integrated dishwasher started bleeping with 3 short bleeps 2 months ago. I followed instructions internet and shook dishwasher to one side and it worked for about 8 weeks. Now it has started bleeping again. Can anyone help?


This is typical of the anti-flood circuit that opperates once it detects water on the base of the machiene and is a polystireen float that activates a micro switch. This puts the machiene in pump out mode only. You need to determine if the water at t ... AEG 23 in. Favorit 86070Vi Built-In Dishwasher

Baumatic BDW5 My dishwasher Baumatic BDW5 stops partway into cycle. Starts bleeping and internal lights start flashing. Dishwasher tablet doesnt dispense. Can anyone help. I'm running out of teatowels!!!


Http://www.manualnguide.com/dl/12334/\015\012Here is the online manual ... Baumatic 23 in. BDW5 Built-in Dishwasher

I have some problems with a Whirlpool DWF 406 dishwasher: The other day, my wife complained about it not finishing a program (just stopped and started bleeping). I saw a post at this forum where it said to clean out the black grid down my the sump. I did that, and then the dishwasher worked fine a couple of times. Today when I got home from work, the machine just bleeped at me and and the green LED light by the start button flashed 9 times over and over again. Does anyone know what those 9 flash


We have the same problem. The dishwasher is 10 years old. In one of the German forums they said that usually it's because the sieve ahead of the membrane has a fine layer of sludge and the pump cannot pump out the dirty waste water. They said that yo ... Whirlpool Dishwashers

Delonghi Dishwasher I have a Delonghi dishwasher - built in unit- which starts in the normal manner but after about 20 seconds, stops and starts beeping with an error message E1. Can anyone help


This is a water inlet problem , not enough water coming in, so the pressure is low going into or thru the dishwasher , check for clogged inlets ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

I have a ADP 4502/5 Whirlpool Dishwasher, when I start a programme it starts normaly but after a few seconds begins to pulse with the green start light coming on and off with each pulse, anyone help?


... Whirlpool Dishwashers

Have kitchenaid dishwasher kuds30fxss3. When pushing start button, start button starts flashing and beeping. If I reset breaker in basement, it will run one cycle and then start flashing the next time. Any solutions?


... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a Proline DWI 5212p dishwasher about 2 years old. Every time I turn it on it starts beeping and the first three lights start flashing. It is draining because if I put water in the bottom it goes when I turn it on but it won't start the wash cycle.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2454 seconds