Having problems with your Dishwashers ?

My bf71 dishwaster has the fault code F the pump is running constantly why?

\015 The pump is running constantly the disply says F\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bf71 dishwaster has the fault code F the pump is running constantly why?


... Dishwashers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

Fault code f70, drain pump keeps running, nothing else works


Hi,\015\012\015\012Yes. F70 is a flood in the base of the unit which activates the float switch and constantly activates the drain pump until the water has gone. Isolate the unit at the power switch and remove the bottom panel under the ... Miele Optima G2470SCVi Built-in Dishwasher

I have a 13 month old Bosch SHE58c dishwasher. The pump runs constantly and will not refill the tank. There are no error codes thrown on the control panel, but not sure there are error codes for this model - the manual doesn't mention any. So I have removed the side panel and can see the bottom pan is bone dry and I made sure the overflow drain switch was not bound and operates freely. Is there some type of reset button or other task I can perform to continue troubleshooting this problem? Repair


I have exactly the same problem. Turn on the machine and it just pumps and pumps, door controls do nothing. According to the technician who came and looked at it the problem is a bad control board. He ordered the part and we are waiting on it. ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

The eco light is flashing constantly on my Dishlex Global 300 dishwasher, it is making a noise like a pump is running continously, but the unit will not operate. Can you give me some possible faults and solutions. Regards Dave I have the same problem. The Eco light flashes and there is some sort of noise, not sure if it is a pump or a solenoid, but thats as far as it goes. A friend gave me the machine after aservice tech told him the main washer motor was gone. i have fitted a new motor, but


Its an overflow of water into the base of the machine.There is a float switch in the base of the machine in a small plastic dish.There is a metal cover with 2 small bolts that have to be removed to get to it.get the overflow c ... Dishwashers

I have a Bosch SHE56C05UC/40. The unit fills and drains ok but the circulation pump will not operate. I run the diagnosis according to another of you posts and came with an error code E1 which is a heating code. Why would this prevent the pump from running? Your diagram show a flow switch in the heating circuit which won't close unless the pump runs. A diagram of the pump circuit would helllllp.


Follow the instruction code in your ins.manual if you do not have go for free download : www. fitness.manualsonline.com or www.ret ... Bosch SHE56C02UC / SHE56C06UC Dishwasher

I have a Hotpoint FDW80 Dishwasher. The drain pump runs continuously, even though there is no water inside, I poured water in with a kettle and it does drain correctly. After a short while fault code AL01 appears. I have removed the base tray to check the "anti-flood" swithch and that is OK, even with the switch disconnected, I still get AL01. Any ideas?


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Fagor dishwasher with fault code F4 and pump keeps running even main switch turned off. Won't stop before totally unplugged.


... Dishwashers

The eco light is flashing constantly on my Dishlex Global 300 dishwasher, it is making a noise like a pump is running continously, but the unit will not operate. Can you give me some possible faults and solutions. Regards Dave


Hi,The symptoms on a Dishlex Global 300 dishwasher:\015\012\015\012eco light is flashing constantly;\015\012noise on pump running continuously;\015\012but ... Dishwashers

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Candy CDi 454-80 e4 error code, all water seems to be pumped out but pump still running, pump start to run when switching the machine on and e4 appears


... Dishwashers

Bosch Dishwasher has started acting upo. If I turn on the dishwasher it runs the pump for approx 2 seconds then cuts out. This carries on the cycle spraying the soapy suds around the compartment but there is no running pump sound. Any idea how I can access the pump to either attempt to clean it out or to replace it? Or does this indicate another fault that may need attention. Any idea of the cost of parts UK. Thanks for assistance ****


Most dishwashers pump out briefly before filling in order to clear pressure chamber. The next step is the water fill which is monitored by the pressure/level switch. Once water level is attained timer will advance through cold rinse cycle. If no fill ... Dishwashers

My asko dishwasher ran great until recently. after finishing a load, the pump just continues to run (even when all water has been pumped from the unit and it's running dry) and the display isn't flashing anything (not codes, etc). Worried about destroying the pump, I shut off the washer at the breaker, and it's been a few months since we've had a dishwasher. Every once in a while I'll turn the power on and it just continues doing the same thing - it's stuck in this position/state, so I have to s


The IC that controls the pump seems to have gone kaput. Change the IC. ... Dishwashers

Shx98mo9uc dishwasher has the drain pump running constantly. Do I replace the pump or is there something else triggering it to keep running? The dishwasher will not drain also.


... Bosch SHX98M09UC Integra 800 Series Dishwasher w/Display

Beko D2731 salt lights and rinse aid on pump running constantly and takes in small amount of water then pump runs again


... Dishwashers

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Dishwashers

Electrolux dishwasher shows code 10 not filling fault and code 20 not draining fault but when running you are able to hear it filling and draining. Whats the problem.?


I had the same issue (Electrolux ESF 6251). I had both error codes 10 and 30. I found that the short hose connecting the inlet valve (solenoid) to the tank was cracked. That explained error code 30, but even after replacing the hose I still got error ... Electrolux Dishwashers

Hello, dishwasher whirlpool ACP 4738 display fault code fb (f6 ?) after 3 minutes run. Do you know what fault code means ? Thank's DT


... Whirlpool Dishwashers

ASKO D1986: Water pump running constantly


Solved by draining water from bottom pan. ... Asko 24 in. D3350 Dishwasher

I have a Bosch Exxcel dishwasher which runs the drain pump constantly even with the door open and despite there being now water in the machine at the cycle wont start. I have checked the warer amtrix and the ffed hose to the sump for blockages. The float switch operates OK but when the water drains down the float drops and the water is pumped in, then the float rises and water leaks out and the drain pump kicks in again and no more ater will come in unless you push the float down. Inside the bas


I am not sure about this model but most models run a drain cycle for a set period at the start of a wash cycle and then move on to normal filling and cycle of machine provided the various switches are at the low level it will carry on to its set cycl ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

D3350 pump keeps running but no erro code


... Asko 24 in. D3350 Dishwasher

Drain pump runs constantly


Timer switch . ... Bosch 24 in. SHU43 Built-in Dishwasher

Danby ddw497w will only be about 5 min into cycle when digital code E2 appears it then starts beeping 2 min after this it just stops the unit is only one day old it ran once yesterday fine now i get this code no matter what cycle it is on I bought mine new off the internet and it's been running great for about 2 months. Now I can't get it to drain and E2 shows, I can't get my money back because I've had it more than 30 days, if the solution is a pump, I'm tossing it and getting a good one from


E2 is a hose issue. There is either a kink in the hose, the hose is too high to drain or the pump is faulty.1-800-26 DANBY ... Danby DDW497W 22 in. Countertop Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1265 seconds