Having problems with your Dishwashers ?

E1 error LG Dishwasher wqill not fill and get E1 error after about 5 minutes. Any suggestions.


Answers :

Called a repair man and 400.00 all fixed
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

E1 error LG Dishwasher wqill not fill and get E1 error after about 5 minutes. Any suggestions.


Called a repair man and 400.00 all fixed ... Dishwashers

Hi my Candy dishwasher model CDI 1012/2 is filling with water then after a few minutes if bleeps and the error code meaning according to the manual is "Longer inlet time. possible cause Faucets is not open" The tap is fully open and the dishwasher is now full of dirty water. Could you please suggest an alternative cause?


... Candy Dishwashers

IE message Getting an IE message on dishwasher. Water is coming into the tank and heating, but after about 5 minutes, it kicks into an IE error. We have checked the water inlet and the spray arms and everything appears okay. I have read the comments about checking the float, but how do you do this? Any other suggestions would be helpful.


My solution was, after LG sent me a second dishwasher that ALSO did not work, to demand a refund. Then I went and bought a KitchenAid~ it's awesome! ... LG LDF6810 Built-in Dishwasher

OE Error I'm getting an OE error which is a drainage trouble error. I checked the hose and the drain, and everything is clear. My diswhwasher runs 98% of its full cycle and usually with 2 minutes to go I get this error. I have 2 opinins as to why this is happeneing. 1. Maybe the clog is in my trash compactor, however that seems to be working fine and my sink is funning with no slow down. 2. My 2nd theory is I have to reset the progam within the dishwasher. Like how sometimes I


Had the same problem and had the pump replaced ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Kitchenaid kuddo1dppa I own a KitchenAid KUDD01DPPA, 2 drawer dishwasher. I am not a technician, however I have had a lot of experience in repairing various appliances and am savvy with electronics and mechanical technical issues. Here's the problem: I was getting rinse error codes in both drawers, pulled the bottom drawer out, removed the cover to the circuit board and used a dryer to dry up the moisture on the flood switch. Now I am getting Fill Failure error code on both drawers. I have g


Test this steps and fix it. God bless you\012 \012 Water Inlet Valve\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

I have a viking dishwasher model DDB325SS that keeps on getting a pan flood error. Once the error is cleared after several day of letting it dry out, I try and run it again. Immediately after starting it and water flows the pan flood error occurs. Any suggestions?


... Viking Dishwashers

My Viking dishwasher won't fill with water. The motor seems to be running but no water enters the chamber. It's Sunday morning so I'm not able to get a repair person here. I got a response that said ''The ventilators are blocked. Turn it off and have the motor checked'' i was hoping for instructions on how to unblock the ventilators or clean it out. I have a house full of people for the weekend and would love to get this thing back up before Monday when a repair person could come. Any suggestion


... Viking Dishwashers

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


... Dishwashers

I have Whirlpool dishwasher DWH B00. Now it starts as normal filling water for a couple of minutes. Then it suddenly starts beeping and pumps out all the water and just contiunes to beep. This will happen in all programs. We have studied the users manual and cleansed the filters as suggested in the manual, but this doesn't help. There are now problems with the water supply. The dishwasher is not used very much, may be just twenty times. In the start it worked normally, this problem suddenly


Hello & Welcome to FixYa If the sound is coming from the bottom panel then it is the motor that has gone bad and needs replacement. However, if you hear the sound from the control then it can be due t ... Dishwashers

My dishwasher was moved for kitchen rennovations. When hooked back up again it would not fill up. It will run through a cycle but no water enters. If I squeeze the rubber hose that leads from the electronic valve to the tub it gets hot indicating that I am forcing hot water through the line. If I pour water into the tub it will wash the dishes but at the final 6 minute point it will go no further, I assume because it is not getting rinse water.


Hello,\015\012Make sure that a wire did not get bumped off of the soleniod valve. It sits usually on the bottom front left hand corner of the dishwasher.\015\012If the wires are both on the valve then the valve may need ot be replaced... ... Dishwashers

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW


... Dishwashers

I have LG dishwasher model LD 14AW1 I get error the message HE about 15 minutes into the wash cycle then the dishwasher turns its self off


HE refers to HEATER ERRORThe water is not heatedor the temperature inthe Tub is overheatedto over 95¡Possible causes¥ The Circuit of Heater is troubled.¥ The Thermistor is troubled.¥ T ... LG 24 in. LD-12BW5 Free-standing Dishwasher

We have a kitchenAid dishwasher -- just installed last year new-- we cannot get the rinse aid low light to go off. We have filled it up to where it can no longer hold anymore and the light is still on. I have tried to cut the power on/off and it still remains on. Any suggestions on how to get the light to go off? thank you.


Check to see if the "Heat Dry/Lock" button is lit up. If it is, press the button and hold it for four seconds to unlock your dishwasher controls.Close your dishwasher door firmly and press the "Cancel" button. Wait two minutes for your Ki ... KitchenAid Dishwashers

I have an lg dishwasher mod#LDF7811ST, get error codeIE, changed the inlet valve, machine worked once then got IE error code again. Any suggestions?


If you are getting a IE or similar error on your LG dishwasher and have not been able to solve the problem using information based on that code, check the serial number of the dishwasher. If the first three numbers are between 501 and 702 you may ha ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

My dishwasher will not drain. it goes through the first 10 minutes of a program then i get the OE error code. i have checked my hose for kink or clogged-there is none, i have made sure it was level. i would like to get the filter off but it looks like i would have to take the drain pump out from the bottom to check if any thing is plugging it. was just wondering if anyone has any tips that would help. thanx


1)check the drain pump working\015\0122)check any block from drain pump to drain hose. ... LG LDF6810 Built-in Dishwasher

We have a Sears Ultra Wash III dishwasher, model 665.1677993, bought in October, 1995. It is not filling with enough water to get the dishes clean. I took the water valve out and looked at it and it seems okay. It doesn't look like the valve is opening all the way - just my guess. A small stream of water comes out with good pressure, but it is a small stream. I can't find any screens or filters in the water line coming in. The fill cycle lasts only about a minute. Is that adequate? Steve


There should be another letter after the p in your model number. If it's just a B then there are no parts available for that model. Typically a dishwasher will fill for 90 seconds or more. One minute or less sounds like you have a control board is ... Whirlpool GU2400XTP Built-in Dishwasher

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

Hi there, we have had our Bosch Loggixx Auto Option dishwasher for about 5 years now and we seem to have had endless issues with it. However, it now seems to have an error with the timer, which on any wash it seems to get to about 6 minutes and then jumps to 32 minutes and the contents are not being cleaned. Any advise that you would be able to provide would be greatly appreciated. Many thanks


There is way's to fix this problem, first check the amps that is going to the dishwasher, and them repplace the timer.\015\012\015\012can be a electrical problem that is keeps damaging the dishwasher. ... Bosch Dishwashers

My Miele Dishwasher (Excella Series G 2630 SCi) fails to fill. I get the message "Water inlet - Open the stopcock". I checked the water inlet filter and looked for hose kinks to no avail. I even checked the non-return valve. When I start the dishwasher I can hear a low hum (Not the pump) for a few second before the error message displays.


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

Model #363.14232100 dishwasher. When you turn the switch to on, it will not come on. If you keep turning the knob slowly you can hear the dishwasher trying to start up,but it doesn't. Keep turning the knob and its the same thing, sounds like it will start, but it doesn't. It did fill with water, but once it was opened it didn't start up where it left off. The lock switch was in position, and still nothing. Now I have water in the bottom but can't get the thing to come on. Any suggestions? Help!


... Kenmore 24 in. 16539 Built-in Dishwasher

I have an Miele Optima Series HG03 dishwasher. The dishwasher stops after a minute and the intkae/drain error flashes. I tried everything in the manaual but there is nothing blocking the drain or intake hose as far as I can tell. Any suggestions of what I should try next?


Hi,\015\012\015\012try checking the spigot under the sink as quite often the hole has not been opened up enough and there is a shoulder for food to jam up against causing a blockage. Remove the drain hose and have a look in the hole of th ... Miele Optima G2470SCVi Built-in Dishwasher

My dishwasher just fills up with water and then does nothing for a few minutes..... then it will drain and then fill up with water again...,but the dishes never get cleaned


... Frigidaire Dishwashers

My Frigidere dishwasher 400 Series AquaSurge w/Speed Clean has an error light Er S It indicates low rinse aid but I have filled the dispenser..I can't get the start/cancel button to work or to mov


... Dishwashers

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2365 seconds