Having problems with your Dishwashers ?

Dishwasher confused Dishwasher was switched off just after cycle commenced (tablet had been released). On restarting dishwasher, it wouldn't take in water and has just been going through the motions of the cycle without anything happening. Even when the power button on the machine is switched off or the door is opened, the motor continues to run but without water. Water is definitely switched on under sink. I think the computer is confused - can you please help?


Answers :

I suspect this is nothing to do with switching off during the cycle.
take the bottom plate off and check if there is water leaked into the bottom pan. alternatively, if you can, tilt the machine back to 45deg and see if water runs out.
most machines have a float switch in the base so that if water leaks, all that will happen is that the drain pump runs and i think this is what you are hearing
Forget the float - as long as its not raised then its ok
can you hear the drain pump running or can you hear a low hum when supposed to be draining?
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher confused Dishwasher was switched off just after cycle commenced (tablet had been released). On restarting dishwasher, it wouldn't take in water and has just been going through the motions of the cycle without anything happening. Even when the power button on the machine is switched off or the door is opened, the motor continues to run but without water. Water is definitely switched on under sink. I think the computer is confused - can you please help?


I suspect this is nothing to do with switching off during the cycle.take the bottom plate off and check if there is water leaked into the bottom pan. alternatively, if you can, tilt the machine back to 45deg and see if water runs out.most ... Dishwashers

Got a Indesit Di620 Dishwasher that trips RCD after power up & immediateley as you shut door.Fault is definately related to pressure switch, disconnected pipe to switch and then able to start cycle, without tripping, small amount of water out of pipe,but cycle only lasts for a few minutes, then stops. ( blowing into pressure switch trips rcd )How can i test switch, or is it a water level problem ??Any help would be good, thanks S.C


... Dishwashers

Hi, When I turn on my dishwasher, it fills as normal with water but is not pumping into the upper spray arm. the spray arms are not clogged, I have checked them. Anyway, I always rinse the dishes under the tap before placing them in the dishwasher. I have to switch the machine on/off several times then the pump starts at full force.Occasionally it goes through a complete cycle without havig to switch on/off. It's a Siemens Lady model, E-NR SN53300GB/08, FD 7201 058479. The dishwasher is used


... Dishwashers

Dishwasher Water is not going through upper and lower spray arms. Checked overfill protector switch, inlet valve, inlet valve screen, pump blades move freely, Pumb motor is working , Water enters into machine but does not go throught spray arms. Water heats up, Machine will go through all cycles but without water going through spray arms. 650 / 690 series gldb656jso


... Dishwashers

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor. ... Whirlpool GU2400XTP Built-in Dishwasher

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

Dishwasher will not fill with water, dishwasher sat unused for some time. it worked fine for 4 times, then it backfilled with water from the garbage disposal unit, and leaked out through the floor. When I start a cycle we hear what it sounds like a pump draining and then going to cycle without water coming in. It's a bum.


... Bosch 24 in. SMU40 Built-in Dishwasher

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

I have a problem with my Asko D3350 Dishwasher, can you help? On startup the diswasher does its normal cycle and pumps excess water out and then fills the dishwasher with water to the correct level of water, after this the machine has no dishwashing action at all for the duration of the program setting. The dishwaher then pumps all excess water out and switches off as normal but no washing action has taken place, there are no error codes during the entire operation. Is there any way to rese


Hi Tony,\015\012\015\012I have the same machine (D3350) and almost the same problem.\015\012\015\012Mine starts each cycle fine - pumps out - fills - rinses - pumps out tht first load and then does not fill again. If I manuall ... Asko Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Dishwasher not working. Two weeks ago the heating cycle didn't switch itself off but appeared to correct itself. Now there is no water in the cycle... pump and heater working, just no water reaching the arms of the dishwasher. Any ideas why?


Sounds like a bad pump. If it drains the water and doesn't deliver at arms the pump is more than likely bad. First of all pull the water supply line off and see if there is build up from hard water on the in-line screen (if present), then If you are ... Whirlpool GU2400XTP Built-in Dishwasher

We have a Whirlpool ADP962 Dishwasher that will not fill. I replaced the inlet hose as I thought the solenoid was faulty. It's gone a step further and now sounds like it fills (continuously) however it soon drains without any water entering the dishwashing compartment (this remains dry). I believe this issue was caused by running it through a cycle without the water mains turned on. Any ideas?


Hi.When you say inlet hose I think you are referring to the inlet valve, which has a built in solenoid. The inlet hose is only the rubber hose connected to valve and faucet.Rather than the hose the problem is likely overfill d ... Whirlpool 24 in. DP840D Free-standing Dishwasher

Fphd2491kf dishwasher stop working without compliting cycle leaving water at the botton of the dishwasher and not draining the water I call the experts at Frigidaire and they instructed me to push the Normal Cycle botton so I did and nothing happens some body help me


... Frigidaire FPHD2491K Builtin Dishwasher

The dishwasher starts and initially rinses the dishes without heated water. In the next part of the cycle, the water is supposed to heat to a certain temperature.Beginning this morning, in this second part of the cycle,the dishwasher trips the circuit breaker. If you reset the breaker and turn the sihwasher back on, the breaker trips again. What is wrong and how do I fix it?


Hi\015\012\015\012The issue is with the heating element of your dishwasher, it is withdrawing very large amount of power and thus, the circuit gets overloaded and circuit breaker trips. You'll need to check for any short circuits around t ... Dishwashers

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Maytag Quiet Series 300 dishwasher leaves sediment on dishes (primarily glasses) after running the Autoclean cycle. We've taken it apart, cleaned spray arms, filters, float and replaced some seals, but still have problems. We use Cascade detergent and Jet-Dry (what was recommended when we bought the dishwasher). Our water temperature is 120 degrees (maximum setting we can have without having our tankless water heater modified), but this dishwasher problem was an issue with our old tank water hea


The problem is hard water. www.dishwasherfilter.com has a\012product to solve this problem once and for all. It filters the water going into\012your dishwasher and remov ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

Kenmore dishwasher Food particles left on dishes and inside of dishwasher. All functions appear to be working normally. Water pressure OK, drain OK, water temp OK, Etc. Operating dishwasher though a normal cycle without dishes solves the problem for one load, then back to problem. Dishwasher is about 5 yrs old and worked perfectly for 4 yrs. Any advice would be greatly appreciated. Bruce


... Kenmore 17822 Free-standing Dishwasher

Have a Bosch shy56a05uc dishwasher that suddenly stopped working to a point. I believe it is related to the door latch switch, because I don't feel the door securely latch shut when I close it, and I also don't get any cycle lights or times registered on the LED readout. If I depress the on switch, the drain pump will start even with the door open, and, depending on how long I leave the switch on, water will start to fill in the dishwasher, open or not.


Does your dishwasher electronic control or mechanical timer? if mechanical timer, I encounter a similar problem n change the mechanical timer. that problem solved.\015\012\015\012Prince P ... Dishwashers

I have a frigidaire built in dishwasher, about 5 years old. Model #FDBL960BB0. I had a clogged sink which caused my dishwasher to back up. Had the drain unclogged, went to start my dishwasher, it's making the regular cycle noise but is not filling with water. Is there some sort of safety switch that needs to be reset before it will fill with water?


Yes lift your float,,and drop back into place ... Dishwashers

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers

Own a KitchenAid dishwasher, model KDC-21AD. Unit stopped shortly after startup cycle began. When cycling thru the various wash cycles, I hear a slight hum when selector switch is at the "pots/pan" selection. About 2" of water is standing in base of dishwasher and it will not start. Checked the KitchenAid site and they do not list my dishwatcher. Would like to be able to repair myself or have it done at reasonable price.


... KitchenAid Dishwashers

I have a baumatic mini4 tabletop dishwasher and when i put it on to start a cycle after 2 mins water starts pouring out the bottom of the door and floods my kitchen? i have checked pipes and they are ok and when i switch the dishwasher off and back on again the water drains out the bottom of the dishwasher ok.


Hi,\015\012\015\012As there are a couple of troubleshooting for this leak. As with out doing it is not easy to understand whether its a plumbing issue or the washer is not draining constantly in cycles.\015\012\015\012 ... Baumatic 18 in. BFD46 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2593 seconds