Having problems with your Dishwashers ?

What cycle do I use or fine china?

\015 What cycle do I use for fine china.....I have the bosch\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What cycle do I use or fine china?


... Dishwashers

What cycle should I use for fine china? If just cleaning china stored and dusty, would a rinse with no detergent work well, with gold trim?


Light wash or short wash .sprinkle a little (small shot of gel)detergent in bottom of machine(will kill any germs) and let run. Rince only just wets them. I would hand dry after. ... Dishwashers

I have a Whirlpool Gold Quiet Partner III (Model GU1200XTKB0). I have used it previously on "Normal" cycle and I always keep it on Air Dry. Last night I used the "Pots and Pans" cycle and it seemed to work fine. But this morning the Air Dry light is flashing and if I press a cycle key the Rinse Only light starts to flash as well. Nothing works. I have made sure that the console is not locked. Any suggestions? I do not have a Heated Dry button, only Air Dry. Thank you.


... Dishwashers

Frigidaire Dishwasher Model #FDB1500LFS2 After finishing all cycles, no problems at all. But if it was not in use for couple days some dirty water back up at the bottom. Then just let the machine run and wash another full cycle, everything is fine, but couple days of no using , dirty water back up again


... Frigidaire Dishwashers

The dishwasher does not complete a cycle. It starts the cycle just fine but then it stops after one minute. It seems like it gets stuck and won't move to the next step. I do hear a slight clicking noise similar to a clock ticking, like its trying to move on, but then it stops. It clicks three times. When I open the door the "fine china" light is on even though I set it on "normal". Is there a "re-set" button?


The Control Board is gone, the part is $475.00 Find a new one.... ... Viking Designer Series DFUD041 (Premium) Built-in Dishwasher

I have the Whirlpool washer model # wtw5300vw2. What is the accurate amount of water this washer should use PER FULL LOAD/COMPLETE CYCLE on the super load with NO extra rinse? Reason being... Google isn't helping me here. I check my mention before and after I washed it says I am using 145 gallons of water PER COMPLETE CYCLE. Is that right, or no? That seems very high to me. I called the water company to have them check our meter. The meter is working fine. Guess we was comparing it with our


... Dishwashers

I have a Whirlpool Gold (Quite Partner) Dishwasher that is about 9 years old. I was using a liquid gel Dishwasher liquid and it has been working fine. After I switched to a Cascade Action Pads (solid powder pallets), its detergent dispenser did not open during the wash cycle. I cleaned the dispenser and switched back to liquid gel. Now the detergent dispenser (that looks clean and fine otherwise) has stopped opening during the wash cycle. What's wrong and what can be done? I can be contacted


As well as controlling cycle times, the \015\012timer on many dishwashers also functions as an actuator for the \015\012spring-loaded dispenser door. At a certain specific time during the \015\012cycle, the timer will activate a lever that in turn op ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

Not draining caloric dishwasher is not draining...was working fine before i stopped it mid cycle to take out a glass...then the next time i used it i put it on the pots and pan cycle and after it dialed to off i opened up and found a "block" of detergent and it hadnt drained... i just put it back on the normal cycle and am trying again... we'll see ?


Does the motor come on when it is supposed to drain? If it does then by stopping the unit mid cycle you could have had a freak instance of food particulate blocking the air gap located on the back of your kitchen sink (if you have one) It would loo ... Caloric 24 in. CDU210C Built-in Dishwasher

Hi our Touchdry model dishwasher isn't disolving the soap powder, we use the recommended brand Finish, worked fine up to a couple of weeks ago, now there's still a large lump left in the dispenser every morning - I always use the econo cycle, and the machine is always full up with dishes. Used a Finish cleaner yesterday but still no improvement. What's happening?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... Westinghouse Dishwashers

The Normal wash cycle won't light up. Only china cycle - just bought used dishwasher.. GE Profile 5 wash cycles stainless


Does the normal wash cycle work though sometimes a ligt might be gone on the control if the wash cycle doesnt work then your in for some headahces unfortunatley you would have to be able to diagnos which is the problem either the main control or the ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

I have an older Maytag model #WU482. For some reason it will not drain and will only run using the economy mode. I can hear the timer ticking at all other cycles and it does click between cycles. I recently replaced the drain float and the machine had been working fine after. The motor is working and the belt is good. I think the kids were playing with the timer knob. Could this cause a problem with the timer motor? Or does this sound more like a pump out issue, impeller? I'm thinking its


First,inspect the drain float. Make sure it rides on the micro switch correctly or it will not take on water.Check the float micro switch for continuity. Check for power at the water valve when it calls for water. Remove the wire harness from the tim ... Maytag 24 in. PDB1420 Built-in Dishwasher

I have a Kitchen Aid KUDS03CTSS3 dishwasher. Dirty water is staying at the bottom and nothing comes out the drain hose during the entire cycle. The drain hose is looped above the kitchen P-trap, although for a time it wasn't. I use a wet vac to get the water out but there is still water below the fine filter. I thought if I could get the fine filter off, I could clean out the bottom as I think that it's full of crud down there that may be blocking things. I can't figure out how to get the l


Hi,Thanks for the follow up. I am glad it worked out for you. If I can Help in the future let me know. http://www.fixya.com/support/c64627-kitchen_aid ... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

Whirlpool gold quiet partner iii was making humming noise. I took apart and found a couple of rubber and a plastic straw. Thinking I had it fixed, I ran a cycle. It started fine, however it stops using water. Same with rinse cycle. Sometimes it works, sometimes it doesn't.


... Whirlpool Dishwashers

My Whirlpool Gold Quiet Partner III was DOA when I went to use it today. I unplugged/plugged it back in, at which time the "China Crystal" LED flashed a sequence of 3 flashes, then 3 more flashes, pause, 3 + 3 more, pause, 3+3 more, pause, etc., etc. And it would not run on any other cycle, but it did seem to run thru that one OK. Upon completion of the cycle, it was DOA again. Did the "Normal/Air Dry/Normal" button sequence, and now the Rinse Only button is steadily flashing. Any suggestions? I


When the rinse light is flashing steadily then the reset procedure for your model is pressing the "Normal/Air Dry/Normal" buttons.\015\012\015\012If it did not reset your dishwasher the control board must have fa ... Whirlpool GU2400XTP Built-in Dishwasher

Kitchenaid Dishwasher KUDD03DTSS10 Leaking from front of bottom drawer out of air intake assembly.first use. testing on rinse only cycle per installation instructions. Top drawer fine throughout cycle, no other leaks


... KitchenAid Dishwashers

My Maytag dishwasher is 9 years old-- Model number MDB7100AWW, serial number 27754072ZQ It has worked fine until about a month ago, when I began noticing a kind of "scum" on the silverware and some of the dishes after completing a wash cycle. The top rack will squeak and have some resistance when pulled out, whereas before it always came out smoothly. I have always used powdered Cascade. I've tried using less, thinking I might be putting too much in. Then I got a rinse agent. These thin


We had the same problrms, and then the machine wouldn't even clean anything, we took apart the lower spinner and cleaned the plastic filters and now it works like new ... Maytag Dishwashers

My Frigidaire PLD4460REC0 dishwasher status indicator is completely black. The window used to have a green display with the cycle timer. The dishwasher seems to be working fine and I can even change cycles but the status indicator is blank.


Hi\015\012\015\012First make sure that nothing is blocking the drain pump\015\012assembly located inside the lower front panel of the dishwasher. If the issue\015\012returns after its cleaned then try to reset the dishwasher control by pr ... Dishwashers

I have a Fagor LFF-021 dishwasher, two years old. It has not been used for some time. I have tried to start using it again, it washes fine, but won't move on to the drying cycle. Just keeps washing forever and never stops........... Any suggestions?? Many thanks


... Fagor LFA-65 Stainless Steel Built-in Dishwasher

Our GE Profile (Quiet Power 6) dishwasher is having trouble cleaning our dishes. The top shelf rarely gets cleaned and the bottom is questionable. It used to work fine. We always use Cascade powder detergent on a normal wash cycle. We have hard water. Any advice would be appreciated. I took apart the washer looking for an obstruction but none existed.


The obstruction can be external to the unit. Check the drain at EACH connection working backward from the sink connection all the way to the motor pump outlet hole. Do not forget to dis-assemble the Air-Gap (if installed) and to check the inside of ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

GLD6200 NOISY We have above unit approx. 2 years. It just started having a "rumbling noise" when running (all cycles}. The floor even vibrates mildly. It works fine just annoying - it used to be very quiet. Everything I know how to check seems fine. Do I need a repairman ?


The sound is almost always caused by a worn docking cone “O” ring on the main conduit. When the docking cone “O” ring wears, the mid level spray arm conduit is no longer constrained and it can vibrate against the docking cone, ... GE 24 in. GLD6200L Built-in Dishwasher

Heated drying cycle on Kitchen Aid (12 yrs) not drying upper row glasses. Also there is significant spotting. Is there a way to thoughly clean the machine from years of use. It works fine otherwise through all cycles.


The best way to clean it out is to run a empty load with a coffee cup full of vinager on the top rack, you might need to do this a few times to get all the gunk out. As fas as the drying goes check you heating element at the bottom of the tank and lo ... KitchenAid Dishwashers

Currently the only setting that is working is Sani Wash. If I use any of the other settings the Intake Drain light comes on and everythig stops. How can the Sani Wash cycle work fine and no Intake Drain light when all other cycles trigger the Intake Drain light and won't continue to wash? Thanks,Karen


I decided I'd wait for the repairman; I don't want to have to pay additional money. ... Dishwashers

I have a built-in Bosch dishwasher SHU 4302 UC. It no longer drains the water out at the end of all the cycles. I have tried everything mentioned in the booklet (make sure water is hot, use the jet-dry stuff, make sure outflow hose doesn't allow water back in). I have to siphon out at least a good bucketful of water. (Also, only the regular wash cycle works, which is fine with me.)


The problem is a solenoid on the bottom of the unit. It is a small black cylinder next to the pump. It operates the valve that changes to the drain cycle. You can probably order one from Bosch ... Bosch 24 in. SHU43 Built-in Dishwasher

Meile G 1534 new dishwasher was installed by plumber on friday, it completed its first cycle fine , however when the next cycle started it makes a horrible dry grinding sound from the cabinet/ door and does not seem to be pumping water. i use tank water


Wondering if you called the plumber who installed it. \015\012\015\012Check if the water tank is not empty or tap is closed. It could be the inlet valve of dishwasher trying to open up or the detergent dispenser door solenoid.\015\0 ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1275 seconds