Having problems with your Dishwashers ?

CDA wc140, dishwasher stops after 30 seconds, lights indicate heater sensor problem


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

CDA wc140, dishwasher stops after 30 seconds, lights indicate heater sensor problem


... Dishwashers

FDW60 Hello, I have a Hotpoint FDW60 dishwasher. It seems to have the usual quality issues but the actual problem is different to most I see on here. The machine has only been used about 20 times, but yesterday the following happened, I loaded and selected intencive program, when I pressed start the machine made a shriek/chipping sound, it seemed to run for about 5 seconds then stopped with the power and prewash lights flashing erraticly for about 3 seconds then was totaly dead, no power light o


Tom,\015\012If your dishwasher is still under warranty, best thing will be to contact Hotpoint's service center for repair the problem. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

We have a KitchenAid dishwasher (KUDI01FLSS6) which has not been working properly for a long time. We have the dreaded green blinking light mystery. We understand that this could indicate several different problems. We have found that if we run the sink water until it is hot, then start the dishwasher, and then after ten minutes we open then shut the door, it will consistently run the full cycle perfectly. Does this give you any hint of what might be the problem component -sensor, element, the


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have Whirlpool control board part #8267371. The problem is that the dishwasher does not complete a cycle. A green light on the door will flash. From what I understand it indicates a failure in the heater at some point. I replaced the heater and all I am left with now is the possibility that the control board has failed. So my question is this. Are there common problems associated with these boards ? Which components should I be looking at ? I don't have a schematic. Or is there anyone that can


Yeah, I'm in the middle of that, too. There's a thermal fuse you can check with a meter just above the control panel inside the front door. It should be 0 ohms. Then it's the control board, I guess. Looking for the same one myself right now. I'm goin ... Kenmore 24 in. 16032 Built-in Dishwasher

Lamona dishwasher hja8631 programme indicator lights not cumming on when I turn it on they all flash at the same time after 5 seconds when turning on then go off the salt level indicator is the only light that stays on what can be the problem


... Dishwashers

My CDA CW497 has developed problem. When i select a program say 70 degrees and press the start button and close the door the dishwasher starts in the the normal way bit after about 15 seconds the dishwasher stops making any noise and beeps once. When I open the door the green on/off light intermittently flashes. Any thoughts what the problem is please?


... Dishwashers

After starting wash cycle the rotary dial advances to what appears to be the second phase and stops at about 1 oclock position. I replaced the timer/switch, same problem. Could I have a water temp sensing problem due to a poorly adhered sensor? I thought this may be the issue as the sensor at the water feed near the soap dispenser was loose on inspection. Model Bosch SHU4002UC/U06 Under counter Dishwasher


Check the thermostat sensor. If the sensor is faulty the amchine will not detect that the right temperature is reached and the cycle will not advance.The thermostat will read low ohms (about 1K) using a multimeter at Rx1 at ro ... Dishwashers

Dishwasher problem dishwasher begins to wash, water flows in, then both first and second green indicator lights flash together and the cycle does not complete. I have cleaned the filters, removed water that's left in the bottom of the dishwasher.


My dishwasher Indesit DI67S will not run on the number 1 cycle. It will fill and then when that programme finishes it jumps straight to the drying cycle missing all the rinses out etc. If on the number 2 programme it goes all the way through but then ... Indesit 24 in. DI67 Free-standing Dishwasher

This is a past problem posted that I am now experiencing with my Kenmore Elite Model 655.17489300 dishwasher. Looking for any suggested solutions, Rick Past Problem: I have the same problem with my 2004 Ultra Wash Model 665...fills with water, sensing light comes, then stops for a second. Then you can hear another pump kick in (it hums) and just runs continuously but no water is spraying through the arms. When you cancel the wash, it drains perfectly. I've checked the filters, all is c


The symptoms you have mentioned could be linked to the soil sensor which some models come with. The purpose is to run the drain pump and let more water flow through inlet valve if during wash cycle the dishwasher detects soil collection in the accumu ... Kenmore 24 in. 16539 Built-in Dishwasher

I have an electrolux dishwasher Model # EIDW6105GS1 that for the second time has stopped working and all the lights at the top control panel are flashing...what might this mean? I removed the panel down below the door and it appeared to be a drainage problem. The first time it happend was about 1.5 yr after purchase...(No more warrenty and no extended warrenty)...I drained the water in the pan below and it worked once again. After about a month I am having the same problem.


... Electrolux EIDW6105GB 24 in Builtin Dishwasher

Hi there, I owe A GE GSD5911D01SS Perfil Performance Quiet Power III dishwasher. The problem is that during cycle, it leaks water through the left corner, is like the water level is too high, the sensor light lit up, which doesn?t tell me much. This issue doesn?t happen all the time, yesterday was the second time and I have no idea of what it could be the problem. Can anyone help? Thank you.


... GE Dishwashers

My dishwasher (indestit) will not fill up with water. A technian came today and advise that there was very little water coming through the hose and therfore had a blockage. I replaced it today and it fixed the problem, however onn the 1st wash the cycle appeared to stop rather than completing fully. I have since tried to restart and have the same problem lights 2 and 3 are flashing indicating there is no water getting through, how can this be.


Hi,Here is a tip that will help you to find out why water will not come into thedishwasher... Dishwasher Trouble No Water entering Dishwasher ... Dishwashers

Hi I have a Zanussi ZDF501 dishwasher that stopped heating up intermittently. It got worse and I fitted a new heater and all was ok for a few months. Then the intermittent failure started again. Note that I tested the old heater and it is actually OK without a short circuit so I don't think it was the problem adn can be re-used. Could it be the thermostat or heat sensor? I am concerned it might be the PCB since the failure was intermittent. Thanks Dave


In my case, although the solder joints on the relay looked poor, improving them didn't help. I had to replace the relay. Fortunately, Maplin stock a compatible one, JM67X for 1.99. See ... Zanussi Dishwashers

Have a Miele G1220SC dishwasher. It recently developed a strange problem: when switching it on ALL program lights come on and the machine starts taking water. after a while it stops taking water and starts to pump water, all the time all program indicators remain on. if you leave it on a while ( about 4 or 5 minutes) it is impossible to switch off the machine with the main switch, all you can do to stop it is unplug it. anyone experienced something like this and have any idea what part is malfun


Follow this steps and fix it. God bless you\012 \012 Heating Element\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Miele Dishwashers

Whirlpool DU1145XTPQ dishwasher clean light is flashing. We cannot stop the flashing and the dishwasher will not work. The book says it is the heater circuit. What should we check? What is the most likely problem?


... Dishwashers

Electrolux ESL63010 integrated dishwasher 10 months old- works for a few seconds, then stops and beeps continously. & the End indicator light flashes once. I turn it off, cancel programme, set it again, shut the door -it starts and goes on to complete the programme and washes the dishes perfectly. It has been doing this 'performance' for a week now -every time I use it- can you shed any light please


... Electrolux Dishwashers

Siemens dishwasher stopped taking in water red light on indicating this problem, I have checked the water supply to the machine and pressure no problem there any ideas would be appreciated thanks G


Click this link: Cleaning ... Dishwashers

I have a Zanussi dishwasher model IT 5614. When I turn the dishwasher on, the indicator light is already stuck at "BIO 50" and won't move, and the dishwasher won't start when the door is closed. This just happened today. The indicator light for dishwasher salt was also on, so I added dishwasher salt and that light went off, but the machine is still stuck. The instruction book says that when this happens, technical assistance is needed. What exactly is the problem, and is it anything I can


It has been suggested to switch the machine on/off a couple of times and the flashing light will not reappear. Until this light goes off the dishwasher will not start. All the filters should be cleaned free of any leftover food particles. What i mean ... Dishwashers

Dishwasher works for 15 seconds then it stops, and indicator says cycle is finished. when i try it again it only fills with water and nothing happens. i'm wondering if it's motor problem or if there's something wrong with the pump. if it's motor, do you know any place online that i can order it? thank you.


The pump and motor comes as one unit. Motor does not come seperate. Pump parts can be sold seperately ... Moyer Diebel 401HT Dishwasher

I have an indesit dvg 622 kix dishwasher and about 30 seconds after starting a programme the 1st indicator light starts flashing and the machine sounds like it is going through a emptying cycle what could the problem be


... Indesit Dishwashers

Hi I have an F&P DW691 dishwasher (manufactured by whirlpool) the reser light is permanently giving two quick sucessive flashes and will not start the machine unless held on for 6 seconds, the machine then starts for a minute then stops and goes back to the two flash reset problem. Does any one know the fault code applications for this model.thanks Mike


Hi, I've got the same dishwasher but with a different fault, there's power down the cable to the d/w but no power lights on the front panel?Thanks. ... Fisher and Paykel Dishwashers

My Westinghouse 912 Diswasher stops 10 minutes into the wash with the indicator light showing FL with no washing having started as the detergent dispenser does not open and no hot water has gone through the machine. Is there something I am doing wrong or is there a problem with the dishwasher?


... Westinghouse Dishwashers

Fisher & Paykel dishwasher beeping with red light indicator. Won't stop unless unplugged. Doesn't work, (won't drain when it did work), can't change cycle. Have not used it in a long time due to problems


Try pulling out the bottom drawer and check to see if there is a puddle of water around the circuit board, if so it will make it do a lot of wierd things. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Brand new Miele 2170/2180 dishwasher. First time we try to use it, it stops after a few minutes, the warning beep beeps incessantly, and all of the program lights are flashing. According to the manual, we should turn it off and on and then try again, which we did. The problem persisted. The manual says that this may indicate "a technical fault" and we should contact customer service. Unfortunately, they are closed for a three-day weekend. Any suggestions?


It is just possible you have a problem with the drain.if you plumbed the drain to a spigot on the sink trap, did you make sure the spigot is not blanked? the sink spigot will be blanked if it has not been used before to stop water from the sink ... Miele Dishwashers

Kenmore elite dishwasher model 66516052402 troubble shooting light indicates that there is a problem with the heater circuit. How do you locate the faulty component?


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2538 seconds