Having problems with your Dishwashers ?

How to replace the circuit board on my kenmore dishwasher


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore 665.13823 dishwasher couldn't stop a washing cycle. It was identified as "control board" issue. Is it possible to fix the circuit board/timer insted of replacing the board? Also, where are the mayjor screws located to open the housing for the control board? Thanks


Hi,Unfortunately there is no way to repair circuit board or timer. The procedure to replace control panel is :-Step 1 Disconnect the power supply to the dishwasher by turning off the circuit breaker. The circuit br ... Dishwashers

I have a kenmore quiet guard 3 dishwasher 665.743833 it does not turn on when i select any cycle non of the lights tuen on i replaced the circuit board and the thermal fuse still nothing what


... Dishwashers

How to replace the circuit board on my kenmore dishwasher


... Dishwashers

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

Kenmore elite dishwasher doesn't cycle repair man says circuit board needs replacing. clean light blinks 7 times


What does it mean you can get here\015\012http://video.aol.com/video-detail/clean-light-blinks-7-times/346645204\015\012 ... Dishwashers

I HAVE A 8 YEAR OLD KENMORE ELITE (WHIRLPOOL) DISHWASHER . THE THERMAL FUSE BLEW AND I REPLACED IT AND THE MAIN CIRCUIT BOARD. NOW THE UNIT APPEARS STUCK IN CANCEL 2 MINUTE CANCEL/ DRAIN/MODE AND THE RELAY CLICKS ON AND OFF TO THE DRAIN MOTOR. I HAVE BENCH TESTED THE DRAIN MOTOR AND IT WORKS FINE WHEN IPT 120VOLTS DIRECT TO IT ANY SUGGESTIONS . WHAT AMPERAGE SHOUD DRAIN MOTOR DRAW?


Hi\015\012\015\012\015\012The drain motor is of 120 V, 50-60Hz and 0.6 amp rating. Dishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visibl ... Whirlpool Dishwashers

Bci450 My dishwasher has been always giving me lots of trouble. It is the BCI450 model from hotpoint. Whenever it reaches the washing stage for steam, it seems to beep alot. Many times they replaced the Circuit board but this problem comes back after 2 months. What could be the reason this is caused? Today they replaced the rubber thinking that water vapour might be reaching the circuit. I got this repaired about 7 times already and each time they replaced the circuit board.


... Hotpoint Dishwashers

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

Dishwasher Model Kenmore # 665 16829000 Dishwasher "Quick Rinse" was blinking and no other buttons would work. Received FixYa solution below: "Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow plenty of air through the two holes on either side. The holes that you need to blow air into are not on the circuit board, but on the plastic underneath the circuit boar


Hi\015\012If the control board detects that a key is stuck in the depressed position, the dishwasher operation will be suspended and the control will flash the light for that key until the condition corrected. If a key without a light is ... Dishwashers

Having trouble with dishwasher- I feel like dishes are not getting clean- will replacing circuit board on dishwasher help dishing become cleaner?


You may need to clean out the filters that keep food from being pumped up to spray out of the sprayers. This will depend on your make and model as to how to do this. Clogged filters will reduce the amount of water being sprayed. Try opening the do ... Maytag Dishwashers

SHU 5316 UC dishwasher by bosch. I think it is from about 1998 or 99. It blew a circuit breaker yesterday. I reset the circuit braker, but it won't even power on. It may have burned something out. We replaced the control board 2 years ago. Please tell us: 1. Is it worth fixing again, or just replace? 2. Any suggestios? Maybe the pump has shorted? THANKS SO MUCH!! Mark


Hi Mark -There's no internal fuse in this dishwasher, so if there's no power you may well be looking at a new control unit and probably another major component as well, depending on what caused the overload or short. The most likely ... Bosch SHU5316UC Dishwasher

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Dishwasher will not start when pressing the start button. Timer light flashed numbers and went off. None of the lights and buttons work. Circuit breaker in electrical panel is working. Does the on/off switch need replacing, or is it possible a mini circuit board is bad? Dishwasher installed in 2000 and is used on the average once per week.


As it is nearly 10 years old i would suggest you replacing the circuit board. To test exactly we would need the help of an continuity tester and multimeter. ... Bosch 24 in. SHU53 Built-in Dishwasher

Have a shu 4322 dishwasher it fills with water and drains but the spray arms do not spray. have not tried anything yet.this dishwasher is not hooked up. it was given to me by a friend who replaced all his appliances.he also told me that the circuit board was recently replaced as part of a bosch recall. have you heard that there was a recall?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012There was indeed a recall involving the control replacement nearly two years ago now if I recall.\015\012\015\012As for checking int ... Bosch 24 in. SHU43 Built-in Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Kitchen Aid KUDKO1ILBS1 which is constantly blinking clean. I have replaced the circuit board once because the capacitors were bulging blown out. After replacing the board the dishwasher has a mind of its own and will start when it feels like it. Now it will not start at all. Buttons do light up when pushed but it always retruns to blinking clean. Got a solution?


Hi\015\012 \015\012If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean ligh ... KitchenAid KUDK01TK - Multiple Color Built-in Dishwasher

Dishwasher still not working after replacing circuit board ASM


... GE 24 in. GSD6660GSS Built-in Dishwasher

I have a Bosch Dishwasher SHU5302. A year ago it just kept on running. I ran a diagnostic test and replaced the circuit board that had a burn spot. The unit washed after that but would not drain wa


... Dishwashers

Maytag Dishwasher Model # MDB7609AWW1 replaced thermal fuse and circuit board still does not work


... Maytag Dishwashers

I have a Kenmore Elite 665 Dishwasher. The front control display has been partially working but the dishwasher still worked. Today when we tried to start it it will do nothing & it is getting the correct power. Would this be the control circuit board or something else?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Kenmore undercounter dishwasher..model 665.16022400. The "normal wash" light keeps blinking..nothing will work on it..I tried reseting didn't work, killed the breaker for a while, didn't work. I tool the panel off and reseated the ribbon connection to the electronic board..didn't work. I'm not sure if I should be replacing the electronic board, or the control panel that contains the buttons. None of the buttons appear to be stuck. thanks - Andrew


Hi,This is a common problem. As i cannot diagnose the machine myself, it would be tough to exactly comment on the fault. However, more often it is an issue with control panel keypad assembly.You need to replace that.Let me kno ... Kenmore 16024 Built-in Dishwasher

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Circuit board replacement in dishwasher - Maytag MDB7100AWB Dishwasher


... Maytag MDB7100AWB Dishwasher

I have the above dishwasher shv57c03uc just less than 5 years old. The door latch does not engage solidly. when i pust start button left side lights on indicator right does not come on and i have to push on button twice for washer to come on. When it does come on the cycle is real short and it does not complete a full cycle. I an asuming the circuit board is defective!! does this sound right? if so how can i replace the board?where can i get troubleshoooting instructions?


Hi\015\012\015\012You are right it is the ... Bosch 24 in. SHV57C03UC Built-in Dishwasher

Dishwasher will not start. Clean light flashes. Time display shows --. Manual states "The diswasher has malfunctioned". (Obviously) "Call for service to check heater circuit". Will replacing the circuit board solve the problem?


Hello, welcome to FixYa.\015\012\015\012I understand how vague those manuals can be, very frustrating.\015\012\015\012In regards to the fault, while the control can be an issue and ultimately require replacement...that is a wo ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1517 seconds