Having problems with your Dishwashers ?

Model FDB750RCC1 goes through pre rinse cycles with no issues. Once the soap drops it puts water in an does not spray. Then drains. Fills again, just heats w no spray, drains. Etc someone said it may

\015 \015

Answers :

There should be an automatic float valve that allows a certain amount of water to fill the machine automatically. There may also be a dial adjustment that allows you to say whether it is a full load or variations less than full. Check to see if both of your water feeds (hot and cold) are suppling enough water. If it is a top loader you can peek inside the machine at various times to see what is going on (there is a safety switch that will turn off the drum activities when you do and resume when you close it). If it continues to drain and fill on the wash cycle without actually having the agitator do any washing, you have a control switch problem! THat main control switch is not advancing as it should. Change it out!
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model FDB750RCC1 goes through pre rinse cycles with no issues. Once the soap drops it puts water in an does not spray. Then drains. Fills again, just heats w no spray, drains. Etc someone said it may


There should be an automatic float valve that allows a certain amount of water to fill the machine automatically. There may also be a dial adjustment that allows you to say whether it is a full load or variations less than full. Check to see if bot ... Dishwashers

I have a Kenmore dishwasher model #665.13842K601. The problem that it has is that it does not seem to be pumping the water around the tub after it fills. It will fill and drain fine but will not wash. I have removed the spray arms and checked all the parts that I can get to from the inside but fear that it may be a pump or jammed impeller. it does make a faint buzzing sound when it should be operating. Any input would be great. Thanks, Matt


It sounds like you have a circulation problem which means that the circulation pump has gone bad. \015\012Circulation pump - http://www.appl ... Kenmore Dishwashers

The washing machine cycles through the prewash cycle fills,sprays, drains. Once it gets to where the soap drops the spraying stops it just fills, sits an does nothing but heat, then drains, refills, a


You have given a very detailed description of the problem with the video.It will however, be helpful if you provide the actual model number to help give a more detailed solution for the problem. It is written on the inside of the door module usua ... Dishwashers

Dish washer does not drain after the cycle is complete. The last few months when the dishwasher is done their would be a small amount of water left in the bottom. It didnt create any problems but would smell after a few days. So we would just run the drain cycle and it would empty. Well i got home to and the wife said the it was really full. The water was dirty and when you run the drain cycle it didnt drain. She said the dishes were clean. So i cleaned the vent, and filled the sink with


Check drain hose and drain pump.End of drain hose must be in same level with machine.Try it. ... KitchenAid KUDR01TJ Dishwasher

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Hello I have a Bosch dishwasher SHU9905UC and went to clean the spray arms etc and ran the machine without the filter screens in the bottom. **** went everywhere, food, soap scum etc and it first stopped draining and filling. Cleared the drain flap and now works on drainng and filling. But now the wash pump is not running. I figure **** is somewhere in the wash pump or blocking a micro switch etc. I can turn the impellor with my finger. Is there a micro switch in the pressure chamber that is a


... Dishwashers

I have an inglis ipu5846 built in dishwasher it fills thaen trys to start but wont start or drain now i took off the lower spray armthe part that is screw down under it tryed cancel drain and it worked put thetop bacck on but not the spray arm and it wont work.what stopping that from working there are not any moving parts on that piece


... Whirlpool Dishwashers

My kleenmaid dishwasher dw35x keeps giving the error that it can't drain and i got someone to look at the drain and they said the drain was fine. the only way i can make it drain is if i put the pipe into a bucket. HELP?!


... Dishwashers

Hello, I've got a Bosch dishwasher that is acting really funny. I've had it for 4 years. It's 630 SHE44C06UC model. It powers and I hear it run, but the cycle ends w/ 1 but it runs forever...and doesn't rinse or drain. Cancel drain works, but there are spots. I have rinse agent, it fills, drains, etc. I'm wondering if someone knows how I could reset it before calling a repair man? It doesn't seem to dry either? Any help? Thanks, Steph


Hello,Welcome to FixYa.Based on your description I'd say the issue is with the control...unfortunately.The number"1" being displayed ( on models with ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Spray arm, 3rd level, fell off. Flower-like looking ring is still attached to top of dishwasher and arm itself is no longer attached. How can I reattach the spray arm to the flower-looking like ring?I have Frigidaire model number PLD4555FRC0; part # of spray arm, 3rd level, grey is 154478202. I called help line and got someone whose accent I could not understand. I think his name was Victor. He left the line and never came back but, before he left, he said he was looking for the part...why he, t


Unscrew the flower looking piece, there is a white plastic retaining clip inside- press it back together. ... Frigidaire PLD4555RFC Dishwasher

Water doesn't come out of spray bar. water fills dishwasher (and can drain), it also gets heated. But the spray bars won't spray any water (top or bottom). Any ideas?


There is a pump that sends the water to the spray bars. I believe it is broken. Perhaps there is a jam but I don't think it is possible because the water is filtered before going to the pump. Anyway. The pump may need to be replaced (n ... Kenmore Dishwashers

Makes grinding noise.spray arm on top not moving. spray arm on bottom barely moving. grinds when draining too. removed and cleaned out holes in bottom spray arm, didn't help, but found piece of black plastic/porcelain with rust on it in the lower spray arm that looks like it may be part of a bushing?


Very possible that it is a fin off the impellers or could be a bushing ... Dishwashers

MAYTAG DISHWASHER MODEL NUMBER MDBTT59AWW...BASIN FILLS, WATER JETS IN SPRAY ARM START TO EJECT WATER AND SPIN THE ARM, BUT PETERS OUT AFTER 5 SECONDS AND DORES NOTHING...MOTOER HUMMS AWY,..DRAINS FIN


... Maytag Dishwasher Motor Capacitor - 99002665

Maytag dishwasher fills and drains but will not spray water


... Maytag Dishwashers

It is not pumping water into the spray arm to wash the dishes. I can get it to fill with water and drain the water, but when it fills and the cycle timer starts, nothing happens, and a slight burning smell occurs. Does this model have a reversable pump or a direct drive? I am thinking this is where i need to start.


... Kenmore 24 in. 16533 Stainless Steel Built-in Dishwasher

Have a shu 4322 dishwasher it fills with water and drains but the spray arms do not spray. have not tried anything yet.this dishwasher is not hooked up. it was given to me by a friend who replaced all his appliances.he also told me that the circuit board was recently replaced as part of a bosch recall. have you heard that there was a recall?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012There was indeed a recall involving the control replacement nearly two years ago now if I recall.\015\012\015\012As for checking int ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher (Whirlpool Model DU930PWQ0) won't pump out. Problem occurred after door was opened during a cycle. Then the pump-out function ceased to work. Washer fills and pumps correctly during the wash cycle. Any suggestions? My guess is that the electronic control may be faulty and it is not opening the solenoid valve for the drain cycle. The other option I have thought of is that the solenoid valve may be faulty and is not responding to the signal from the controller. The dishwasher is n


... Whirlpool DU930 Built-in Dishwasher

Bosch Integra SHU 9955US/12 - when we start wash cycle, the detergent dispenses and the tub fills with water, but the wash cycle never starts (never spins spray bars). Seems like timer is counting down, though, but doesn't start "washing". After waiting awhile, we are able to use the "Cancel/Drain" mode to drain the water. The drain filter in the bottom of the tub is clean.


Sounds like your motor is burned out. The drain motor and wash motor are seperate on your machine. You can check for power going to the motor, but to do this you might have to pull the dishwasher out. While the cycle is running check for 120 VAC g ... Bosch SHU9955UC Built-in Dishwasher

I have a Kitchen Aid Superba KUDS24SEBS1. The inlet water pressure is good and the dishwasher fills and starts the wash cycle, however, after the initial spray of water, it seems that all of the water drains out and there is nothing left to continue the cycle and wash the dishes. It's like it's not able to fill up enough to wash the dishes.


When "full" of water, the normal height of level is about 1/2 below the heater assy(large blackish grey coil below he spray arm).. if theres enough water in the unit nad its still not "spraying",its quite possible that your filter/chopper assy is cl ... Dishwashers

Maytag model MDBTT59AWB does not spray water. Water fills and drains properly and the motor appears to be working as well. Just no water spraying at all. Any ideas? Haven't found any answers anywhere.Thanks,Don


... Maytag Dishwashers

My fisher paykel DD603 fills with water at the start of the cycle and stops with the following error code and a beeping noise: - error U1 spanner symbol - crossed out faucet symbol. The water level is high enough that the spray arm is floating in the water. I am able to drain the water by entering the hardware diagnostics mode and running the motor in the drain direction. By removing the filter plate and examining the impellers I am not able to see visible damage. All filters are clean. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are spot on as error U1\015\012indicates that the dishwasher has twice tried to fill with the required amou ... Dishwashers

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Kenmore quiteguard standard model # 58715142402 fills up with water does not spray during the wash cycle but does drain on the drain cycle.


... Dishwashers

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1312 seconds