Having problems with your Dishwashers ?

Haier Dishwasher Display Malfunctioning

\015 The fill and drain valves weren't working. After pulling an electrical schematic on line, I tested the output on the pc board and found that it was failing. I ordered and installed a new board (P/N DW-0668-10). I ran a rinse cycle and saw that everything was working well. When I went to run a full load on "Normal", the display showed 3H (3 hours). The actual cycle took about 2 hours and 45 minutes which is far longer than what it used to be. Does anyone have any insight that might be beneficial?\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Haier Dishwasher Display Malfunctioning


... Dishwashers

We have a Haier DW12-PFE2-U dishwasher thats 2 years old. The cycle stopped yesterday leaving an amount of water in the bottom and all of the program lights are illuminated with a recurring beeping sound happening. It says in the booklet that the drain hose is too high or bended. But its not. The display does show the time when a cycle is selcted but nothing happens. The dishwasher turns on and off normally. Can this problem be rectified? thanks!


Refer userr guide on page 21. It reads...\015\012\015\012When all the programme indicators " J" blink.\015\012Have you checked whether:\015\012the door is closed properly.\015\012\015\012 ... Dishwashers

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

My Haier dw9tfe3 dishwasher displays an 'E6' error, how can I reset this? Thanks


Anyone found a solution to this problem? ... Haier Dishwashers

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

Dishwasher will not start. Clean light flashes. Time display shows --. Manual states "The diswasher has malfunctioned". (Obviously) "Call for service to check heater circuit". Will replacing the circuit board solve the problem?


Hello, welcome to FixYa.\015\012\015\012I understand how vague those manuals can be, very frustrating.\015\012\015\012In regards to the fault, while the control can be an issue and ultimately require replacement...that is a wo ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

My Bosch dishwasher has several problems: 1) Water doesn't completely drain out and dishwasher kind-of smells when I open it -- I do keep the filter very clean. 2) The dishwasher takes HOURS to go through one load, no matter what the time says on the display and no matter what type of cycle you choose -- quick, delicate or regular. 3) The red display often displays something that looks like "2h" at the beginning of the cycle. 4) The place where you put the detergent doesn't shut.


Hi Kathryn .I think you have a defective pressure switch. The pressure switch is located near to the drain pump, and the device is used to determine when water had been drained completely.Also check the floater switch located ... Dishwashers

Touchpad--No Response The touch pad and Countdown timer display will NOT respond except when the Rinse Only pad is pressed. The Countdown timer displays "9" when this pad is pressed. As expected the light and display turn off after 30s. If after 30s or longer the Start/Cancel pad is pressed with the dishwasher door closed, then the Countdown timer displays "2H" and the dishwasher runs through the ?Auto Clean? or ?Heavy Wash? cycle. Not sure which since neither pad is lit. Is the problem the


The "2H" is an error code indicating the control panel needs to be replaced. ... Bosch 24 in. SHU53 Built-in Dishwasher

I have a Bosch dishwasher Model SHE58C05. This model has two displays, one on the front where you can see and one with the hidden controls that you can't see when the dishwasher is closed. The display in the front all of a sudden stopped working today. Top still works but I can't tell how many minutes are left while its during the cylcle. I did have to cancel a cycle this morning because I picked the wrong one. Is it possible I hit a strange sequence and somehow cancelled this display (wishf


If you check your user manual there is a section that will guide you through turning off/on the display screen. I have tried to include the link for Bosch manual downloader but their site is down at the moment. If you do not have your manual and ther ... Dishwashers

I have a newer model GE dishwasher. About a couple of weeks ago we lost power to home. When power was returned the dishwasher was making a high pitch sound and power was not returned to the front display. I had to remove a black/white wire from front of the display to make the high pitch sound go away. Do you have any solutions to make the high pitch so go away and for power to be restored to the front display? Thank you.


Hello\015\012\015\012High pitch sound comes when the main control also known as the electronic board goes bad and needs replacement. Please try to blow air with hair dryer on the display just to check if that'll solve the problem. Hope yo ... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

I have a Bosch SHU5316UC dishwasher. The last two times it ran, my wife says the display said "CL" (for clean) after running through the cycle, but she heard a "motor running" until she opened the dishwasher. Attempting to run the dishwasher tonight, it won't start - it displays a "P" (error code?) when you attempt to start it. Can you tell me what the error code P is? Thanks, Dave


P stands for program in computer algorthms. The device displays program whenver chages were made to the default settings. A powered on devices least has malfunction only requires reseting to attaon default features. Depending on the type of device, r ... Bosch SHU5316UC Dishwasher

Dishwasher Normally, after the dishwasher cleans the load, it displays green light next to clean. Once the door is opened, the light goes off an dishwasher is ready for next load. But from few days, after opening the dishwasher door, the clean light does not go off, it remains lit. Dishwasher doe snot reset for next cycle. So, I have to go in the basement and trip the main power to dishwasher. That resets the dishwasher. This needs to be done before each cycle. Not sure how to resolve the issue.


Make sure that you do not open the door during the wash cycle. Wait until all the cycles \015\012are complete before opening the door. Especially don't open the door \015\012during the drying cycle. ... Dishwashers

Haier dishwasher has E6 error code - Haier Dishwashers


... Haier Dishwashers

10 beeps haier dishwasher DW12 tfe 4ss - Haier Dishwashers


... Haier Dishwashers

Haier dishwasher hdw300ss - Haier ESD200 Built-in Dishwasher


... Haier ESD200 Built-in Dishwasher

I have GU2548XTPS Built-in Dishwasher. I need to reset this. When I start my dishwasher, display shows "2". After 2 minute display is "- -" Last time I found some code from internet and it worked. Could you help me to resolve this problem? Thanks, Dinesh Gondaliya


... Whirlpool 24 in. GU2548XTPS Built-in Dishwasher

Haier countertop dishwasher will not empty - Haier 17 in. HDT18PA Built-In Dishwasher


There is a filter at the bottom of the tub that has to be cleaned out once in a while. Then it will drain. This should help. It is a plastic looking mesh filter most can be removed and hand washed. Hope this helps. ... Haier 17 in. HDT18PA Built-In Dishwasher

LIGHTS FLASH Hallo, I have a Indesit dishwasher (IDL 750) and the last few weeks there is a malfunction. After 15 minutes that the wash cycle 2) had started the dishwasher stops and the first and third wash cycle phase indicator lights flash, beginning from the right. Could you help me telling me the possible cause of this malfunction. Thank you in advance Fred Tourman Athens, Greece


... Dishwashers

Dishwasher restarting My dishwasher keeps restarting itself, and occasionally the display flickers. No error codes are displayed. It does not restart at any consistent point, seems very random. Any help appreciated.


... Fisher and Paykel Dishwashers

Need a reset code for Haier 4035 dishwasher - Haier DW12PFE2U Dishwasher


... Haier DW12PFE2U Dishwasher

Haier dishwasher Hi my Haier dishwasher is flashing 3 of the 4 leds and beeping 10 times while the suction pump drains the filter then will not start. Can you tell me what this fault is? water pressure OK ,drain isnt blocked,none of the buttons have any effect. Any info would be helpful thanks.


I useto have same problem. For some reason there was water under machine, then i tilted machine, clean water and problem solved. This is built-in dishwasher that is why water acumulates under machine and "leak cut off switch" turn off machine. You ca ... Haier ESD200 Built-in Dishwasher

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

Haier dishwasher settings - Haier DW12PFE2U Dishwasher


... Haier DW12PFE2U Dishwasher

Model IGV 659.1 Dishwasher When switched on the 'time display' takes longer than 2 minutes to display the planned wash duration. The display works fine to set a delayed start. After cycling the start delay round to 0, or after RESET (buttons A and C pressed) the unit is then 'nudged' into displaying a time. After, at last, a time is displayed the unit works fine.


... Kuppersbusch Dishwashers

My SHE4402UC/36 dishwasher malfunctioned all the lights were flashing and the machine was trying to drain. The guy came out and replace the control board. The dishwasher now read 199 on all cycles except the rinse and hold, the santitized light does not come when its done. The repair guy told me the count down timers were flakey on the the Bosch dishwashers and it would learn my dishwashing patterns in time. So 6 cycles later the dishes are still damp at the end of the cycle-the length of the cy


Well its not baloney but it is cheesey. normally changing the module is the cure but it has to be programmed correctly. bosch has a recall so check it out and see because the recall is free and the tech is suppose to know how to program it. go to the ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1746 seconds