Having problems with your Dishwashers ?

GE profile dishwasher - water is filling the air gap and is all over the counter. I took the cover off air gap. Nothing there. What should I do to correct this?

\015 Dishwasher is 6 years old. Have not had a problem with it before. Yesterday I ran it and water started spilling over the counter from the air gap. I read instruction booklet and it said to check the air gap. I did and nothing is stuck in it. What do I need to do to correct this problem.\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

GE profile dishwasher - water is filling the air gap and is all over the counter. I took the cover off air gap. Nothing there. What should I do to correct this?


... Dishwashers

There is gum stuck somewhere in my dishwasher drain line. The water won't go down. I took the inside apart and can see the hole where the drain water goes. I disconnected the drain hose under the sink. I got the water to drain out when there was alot in there, but now it won't drain again. I blew compressed air from a compressor backwards through the hose and it makes a big splash and bubbles inside the dishwasher, but the water still won't go down. I put Boiling hot water and vinager in there t


Ther e is noo easy fix, short of replacing the drain line( if indeed thats where the clog is)although you checked the hose from the under the sink, did you check with in the hole where the sink conection is made??and try disconnecting the drain hose ... Dishwashers

We recently bought a house with a Kenmore 363.16222100 (?) dishwasher. No manual. Monday night it didn't drain properly and leaked some water on the kitchen floor. The cycle had finished when we saw the water on the floor. We bailed out the excess water. I took off the drain cover and insert. I couldn't see an obvious clog problem, but cleaned it out. Then I tried a short cycle, interrupting it to shorten it. No problem. Water seemed to drain fine. I did find a part that looked like a straw and


HelloWelcome to FixyaMy name is Huum,You can find your model dishwashers manual here at this site. this sitehttp://www.managemyhome.com/mmh/lis_pdf/OWNM/L0801624.pdfI feel you should not invest blindly in someone ... Dishwashers

Hi. I had f1 appear on my Gisher and Paykel dishwasher. Unplugged from wall. Few days later dried using a hairdryer. Took cover off pcb board and dried in there as well. There was water on bottom of cabinet so understand the F1. Problem is now, I put cover back on pcb board and tried to power up but it is dead? Any sensor.microswitch on PCB cover, or anything i may have missed? No power at all to unit? Any assistance greatly appreciated. PS - Wall socket finer as powers other appliances.


Wait.................. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

The overflow air drain on top of the sink that is connected to two hoses under the sink is leaking. It leaks out the top onto the counter. I took it abart but am afriad I did not put it back together right. There is a rubber ring that I think must be for sealing and I put it directly on the counter and then screwed down the air valve over this and water s coming out of the air flow valve and all over the counter.


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

GE model GSD600003 repair manual: Before you answer this, please tell me if I will be charged for the answer, in case I'm not interested at this time. Do you have a diagram of the drain area and water inlet area? I took apart the plastic drain cover for cleaning because it was had pink mildew all around it where residual water pools. I cleaned it all up and put it back and now the dishwasher doesn't fill with water (none comes in). I'm just a guest trying to troubleshoot for relatives, so I'm


I'm not sure how mildew can grow in a dishwasher that is working well, but after cleaning it and putting things back together, it does now seem to be working. I thought that the water wasn't filling but I guess the heating element heats up before the ... GE Dishwashers

We have had this dishwasher for approximately 2 years. Dishes do not clean well. For example, I put a mixing bowl in that I just mixed brownie in--and the bowl did not come clean (simply a thick chocolate mix). Glasses do not come clean. They always have a fine residue on the outside (food). My husband just took the (blades) out that spin and dispense water and cleaned them. The water volume seems better now. Still, if I remember correctly, the dishwasher cost around $900. It definitely


Check if the water gets hot . \012\011check if motor spins enough to give pressure water on arms to clean dishes.\012\011clean the filter regulary . ... GE Profile PDW8480JSS Built-in Dishwasher

My dishwasher won't drain. It's a ge triton. Last time this happened I took off the covering to the drain and found a small piece of glasss. This time i find no obstruction but the water will not totally drain. The small area that the water collects in is full of crud making me think it hasn't drained totally in a long time.


... GE 24 in. Profile PDW7800 Built-in Dishwasher

Water is running in and draining right back out. Leaving the dishes completely dry and dirty. I found a part laying on the floor when I took the cover off. I put it back where it came off of and now this problem. Yesterday it was the water not draining at all, now after putting that part back on it drains and doesnt wash.


Was it the float? try this empty machine put 1cup of vinegar or CLR and let it run through machine and clean jets and spray arm as well as soap dispenecer,You may want to try cascade they have rechanged it .Try this and let me know thanks ... Crosley 24 in. CDU600 Built-in Dishwasher

I have a GE dishwasher (GSD4020Y70BB) new in 1996. I replaced the whole motor assembly in 2007, seal was leaking. My dishes are not getting clean now, dried food left on plates, coffee stains in cups not being cleaned. I removed main spray arm, found nothing, turned washer on and plenty of water gushing out. I took the cover off sump all clean. I removed the filter screen in the back, there appears to be a valve with some soft rubber around it. Water gushes out of this, does stop during the cyc


Have you checked the drain pump impeller and drain hose? I am curious if there is a back siphon from the drain hose or the waste outlet at the garbage disposal might be blocked or plugged with food debris.\015\012I wou ... Dishwashers

I have a Whirlpool DUL300XTLQ3 Queit Partner III. The cleaning blades stopped moving-started it-waited awhile-opened it-the blades were in the same position. Took the bottom blade+filter cover off. Then I held down the metal piece on the case and switched on the micro switch on the door to see it running with the door open. The water shot straight up about 4-5" that's it. This does not seem to be enough pressure for the water to get all the way up to the top spinner. Am I looking at a new pump


If there is not enough water, the dishes would not get cleaned. Thiscould be caused by a partially closed water shut-off valve (locatedunder the sink), or a faulty dishwasher water valve (located at thebottom of the dishwasher, behind the kick panel, ... Whirlpool Dishwashers

Something was stuck in the latch, which made the machine not start. I removed item, however, the lights come on, the heat comes on, bot no water or the rest of the cycle begins...help.. I have held down start/cancel and the heat dry buttons. I have unplugged the power for three minutes... I have taken the front covers off, looked through the latch mechanism but found no other issues. There is a little water left in the basin, so I checked to see if there was a clog, by blowing air into th


Hi,Sorry for the delayed response. Your problem dated 30th Sep 2009 was reposted today on FixYa. I am sure by now some other expert must have responded to your question and solved your problem.If this is not the ca ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

The problem started with it not draining correctly and leaving water in the bottom - my husband took it apart and found a bolt in the drain. He removed it and now it won't start. It appears to not have power to the electrical panel- we have reset the breaker several times - left the breaker off for 10 minutes thinking it might erase the memory - I've asked for instructions to reset and I keep getting info that is very far removed from this model. I know it has a protocol because a repair


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012The reset on your dishwasher is as follows, ( I can't locate your particular model number...but its madw be whirlpool so there are only a couple of possible sequences ) however depending ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

We have water leaking out of bottem of door when my MDB4000AWB is draining on last cycle.I took drain hose off under unit and is clean.Hose is also clean at air gap.What should i check next? Thanks, norcalstevo


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012sthyushg ... Maytag 24 in. MDB4000 Built-in Dishwasher

Dishwasher installed correctly? One year old jenn air dishwasher leaves brown **** and water film on plastic components inside, rinse agent used regularly


You must contact to jENN-aIR FOR get customer support, about the material recommend. About some agent used, or if some bad design material from factory.God bless you ... Jenn-Air Dishwashers

My dishwasher is leaking. I took the cover off of the bottom. Just to the left of the height adjustment knob there are 3 holes. The water is coming from there.


Here is a schematic of you machine this is the base ht ... Bosch 24 in. SHU43 Built-in Dishwasher

Honda GC190 no start. Unit has been sitting for 2 years. Drained old gas, cleaned the carb. No go. New plug gapped to 0.030in. Still nothing. spark seems good. Cleaned the fuel strainer and there IS a bit of vacuum at the fuel pump when cranking. Poured a dab of gas into combustion chamber.. Still won't "talk to me" AT ALL. Removed valve cover and checked the valves.. within specs and nothing sticking or hanging up. Timing belt and cam looks good. Took a peak at the coil.. air gap in specs. 1ohm


... Karcher 2500 PSI Pressure Washer

I was trying to wash dishes and i noticed that the motor wasn't running but water was filling up the unit. I smelled something burning, and i shut it off and took off the cover and i felt the motor and it was very hot to touch. I assume the motor is frozen. How do I change the motor? Is my diagnostic accurate?


Hi.From your description it sounds like the pump motor has blown and must be replaced.Before replacement the motor can be tested by jumping eac of its wires to energize it directly, for safety reasons the operation must be done by a ... Dishwashers

Ice maker cannot eject cubes. I took off the front cover and found several contact points for checking the motor, water valve, thermostat, mold heater. There is also a line voltage and neutral contact. Are these contacts live only during certain parts of the cycle? I suspect the heater isnt working to loosen the cubes so they cant be ejected. The motor sounds lilke its running but the ejector is not moving nor is the Gear on the front of the unit. Can someone give me a full description of this t


I usually replace icemakers as a unit. It sounds like the mold heater is out. The system cycles like this: Fill, freeze, mold heat, eject, and start over. The mold heater not working will prevent ejection. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My dishwasher won't drain fully . It still has a bottom full of water after it finished the cycles. We took off the drain cover and it had a lot of "gunk" on the bottom of it. Gross!!! Help!


You may have a part on your machine called a piston and nut, it screws into the soil chamber. it has a gasket on it, and is likely worn from the hot water and you will need to replace this part. not an expensive part. without the model number, i can' ... GE Nautilus 24" Built-in Dishwasher

MacMarkus, I just got parts for the dishwasher. I put the circ pump in and no water enters the dishwasher. I also see that I didn't put a plastic cover on one of the leads, so I need to pull the dishwasher to do that. How do I know if I've installed the pump correctly?


Hi look to have even an even chance of repair one simply must get a service manual for the unit you are working on. Simply Google the exact make and model, plus the words...... "Your-make-and-model" service manual pdf download (enter)\015\012\0 ... Dishwashers

Dishwasher was cutting out intermittently,totally dead no power then after 15mins or so,finally went bang this am,smoke etc,took insection cover off at bottom swit6ched on again to see spark dead short on unknown unit with four wire block connector attatched,two white to same connector and two purple,left disconnected and workin fine,hot water,inlet and outlet both working fine so what does that unit do?


... Bosch 18 in. SRS43E02 Slim-Line Built-in Dishwasher

I have hot air but no hot water in my dishwasher


Yes, usually the heating element provides heating for the water and the air. However, the timer goes through all the stages telling the dishwasher what to do, and since its heating the air but not the water, I would look more into the electrical. It ... GE Nautilus 24" Built-in Dishwasher

Fisher and Paykel Dishwasher, bottom drawer gets water in it. This drawer is seldom used and when used the water empties completely. However, it always has water standing in it. I run the rinse cycle and it gets all the water out but after time the water is back. It is enough to cover the large removable metal cover.


... Fisher and Paykel Dishwashers

I installed according to guide, but dishwasher will not fill with water. Pump sounds much too loud to be normal. Wiring was checked three times for correct connections. Water supply was checked twice for water getting through, no leaks and water supply on. Drain hose is connected correctly and is connected to house drain.


You state the water supply is on.\015\012Have you loosened the compression nut at the dishwasher ell to see if you have pressure to the water inlet to the dishwasher?\015\012Remember the dishwasher will always run a little to make sure an ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0999 seconds