Having problems with your Dishwashers ?

Dish water is not working. Water fills but no noice after that.

\015 My dishwasher is about 9 years old. Use to work good even though it was making loud noise when washing dishes. Since yesterday when we start dish washer, hot water fills in but no sound and no wash. When I cancel the wash it is draining water also nicely. What could be the problem?\012\012Does the motor/pump need to be replaced? Is it a good idea to pay for replacing motor and service or just buy a new dishwasher?\012\012You input is appreciated.\015

Answers :

It's obviously sounds like your pump has gone, but considering the age of the machine, it would probably be best to get a new machine, that way you would have a 5 year warranty with it aswell so it's win/win really!
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dish water is not working. Water fills but no noice after that.


It's obviously sounds like your pump has gone, but considering the age of the machine, it would probably be best to get a new machine, that way you would have a 5 year warranty with it aswell so it's win/win really! ... Dishwashers

My dishes are filled with white residue from the hard water. I've tried vinegar to cut it and new rinsing agents but nothing works. Is there a filter to clean out any hard water deposits? Do I need to check the line for plumbing for hard water deposits? My water softner is working fine, my dishes are filled with white all over them. HELP!


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

Samsung 9E Error - Low Water Level. Dishwasher has worked fine (10 months old). Confirmed adequate water supply/availability. When opening the dish washer after error, the inside has no standing water. I can hear the dish washer initially fill. This happens later in the cycle (maybe 10 mins in) Should I replace the fill switch/sensor. Is there any info available on how to fix it my self. Appreciate your help!


... Dishwashers

I have a Kitchen Aid Superba KUDS24SEBS1. The inlet water pressure is good and the dishwasher fills and starts the wash cycle, however, after the initial spray of water, it seems that all of the water drains out and there is nothing left to continue the cycle and wash the dishes. It's like it's not able to fill up enough to wash the dishes.


When "full" of water, the normal height of level is about 1/2 below the heater assy(large blackish grey coil below he spray arm).. if theres enough water in the unit nad its still not "spraying",its quite possible that your filter/chopper assy is cl ... Dishwashers

Dishwasher does not fill with water when started. Problem began slowly with dishes not rinsing completely. Overfill float appears to work properly. Water fills pipe leading to fill solenoid but does n


I am almost certain that your problem is the fill solenoid.If it does not work, there will be no water entering your machine.I would either remove it and test it or just replace it at this point.Tim ... Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

We have a Sears Ultra Wash III dishwasher, model 665.1677993, bought in October, 1995. It is not filling with enough water to get the dishes clean. I took the water valve out and looked at it and it seems okay. It doesn't look like the valve is opening all the way - just my guess. A small stream of water comes out with good pressure, but it is a small stream. I can't find any screens or filters in the water line coming in. The fill cycle lasts only about a minute. Is that adequate? Steve


There should be another letter after the p in your model number. If it's just a B then there are no parts available for that model. Typically a dishwasher will fill for 90 seconds or more. One minute or less sounds like you have a control board is ... Whirlpool GU2400XTP Built-in Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

My 12 yr old KitchenAid -Sculptura-Model KUDR24SE starts to fills with water and then does nothing else. It will eventually go through the cycles on the panel, but nothing is happening inside. End result is still dirty dishes with water sitting in the bottom that has to be baled out. Cups on top rack don't have any water on the indentations, so it's obvious that the thing filled with water and that's it. I had the motor replaced (supposedly with a new) one 2 years ago so I find it hard to bel


... Dishwashers

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor. ... Whirlpool GU2400XTP Built-in Dishwasher

Frigidaire Dishwasher FDB740RC. Not cleaning dishes well. Just in the past couple weeks. When the dishwasher fills with water, how full should it get. When mine fills, it definitely doesn't go up to the element, and just barely makes it to the float switch (not enough to trigger it), makes it to just below the base of it, doesn't come up the side of it at all. Is this normal, or should there be more water. The Water valve has been replaced already.


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Frigidaire 24 in. FDB740RC Energy Star® Built-in Dishwasher

I HAVE A MIELE G646 SC DISH WASHER AND IT KEEPS LEAKING WATER INTO THE LOWER TRAY AND CUTTING OUT BECAUSE THE FLOOD SYSTEM KICKS IN.I HAVE THE MACHINE IN THE GARAGE WORKING UP ON TWO WORK MATE WITH THE UNDER TRAY OFF FOR THE FIRST FEW CYCLES THERE WAS NO LEAKING THEN WE FOUND IT LEAKING DOWN THE FILL PIPE.THE WATER IS LEAKING FROM AROUND THE AREA THE FILL PIPE FITS TO THE WATER SOFTNER BUT NOT ALL THE TIME.AN ENGINEER FROM MIELE SUGESTED IT COULD BE THE VENT INSIDE THE SIDE OF THE MACHINE BUT EV


Have you made sure the water sofener filler neck locknut is tight to the bottom of the dishwasher?i have had experience with one machine where spilled salt was not rinsed away after the softener was filled and this corroded a very small pin *** ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

It is not pumping water into the spray arm to wash the dishes. I can get it to fill with water and drain the water, but when it fills and the cycle timer starts, nothing happens, and a slight burning smell occurs. Does this model have a reversable pump or a direct drive? I am thinking this is where i need to start.


... Kenmore 24 in. 16533 Stainless Steel Built-in Dishwasher

Frigidaire fdb1500lsfo built in dishwasher. Have had for maybe 3 years. I push the start button, and it starts like usual, filling the tub with water. After filling, it will not do anything for about 5 mins, where then it drains. It seems to go through the whole wash cycle, but after it has pumped the water out. Dishwasher steams all of the dishes, but there is no water in it to wash them with.


... Frigidaire FDB1502RG Built-in Dishwasher

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr


WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

HI there dish washer wont fill Ichecked fill valve its ok but there is no 110 volt reading to wires but when i remove purple wire from water valve and put ground wire to fill valve water comes in the dishwasher please tell what needs to be replaced thanks


There may be problem with your door switch/lock mechanism,be sure to check the main power supply to the dishwasher.\015\012if you have a electronic control board it might also have to be replaced. ... Dishwashers

GE Dishwasher fills with water but does not "spray water" on dish


Here are a few things that might help you out, first is you could have a bad heating element in your dish washer, when it fills with water it has to reach a certain temperature before continuing to the next cycle, next thing is you could have a bad t ... Kenmore 16522 Built-in Dishwasher

We lost electricity very briefly today which caused the dishwasher, washing, drying, clean buttons to blink when the electricity came back on. I opened the door to do a load of dishes hours after the electricity came back on and the basin was filled with water which caused water to spill out of the dishwasher. The basin was empty last night when we used it. It seemed to fill up when it was not running.


It seems unit fill valve is stuck open and water is coming in even when machine is off.fill valve opens up only when u start the unit.2 chks this u can open the door and look at the hole inside from where water comes in.if water is coming in with do ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Dishwasher fills tub continuously until float turns it off whether in cyle, during drying or after cyle complete. That means during drying when the dishwasher is trying to dry the dishes the tub fills up preventing drying. This is a new dishwasher that I've never used. I allways noticed the tub was full of water, but thought that was just to keep the seals moist so they don't rot. I've been in my house 5 years and only hand washed my dishes because it was more convienient. Now that there ar


Ayacht, the fill is a timed fill controlled by the control board (part number 99003158). The float is a safety device designed to cut power to the valve in the event of a failure. The fact that the float is doing it's job and stopping the fill tend ... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

My dishwasher emits a dead animal smell immediately after filling. I have a 20-year-old KitchenAid KUDS220T3 dishwasher. The racks are a little corroded, but it still cleans dishes just fine. About two months ago, it started smelling like a dead animal immediately after the dishwasher fills with hot water, during the time the water is being heated, but before agitation begins. The smell appears to be coming from around the door. If I open the door, everything inside the dishwasher smells fine.


This vent that you are describing is to allow air to flow in for the heat/dry cycle. Some times little creatures want to "mark" their territory by "spraying". Spray some type of cleaner like ammonia into it and **** it out with vacuum a few times. Mo ... KitchenAid Dishwashers

My dishwasher just fills up with water and then does nothing for a few minutes..... then it will drain and then fill up with water again...,but the dishes never get cleaned


... Frigidaire Dishwashers

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Water softener Salt residue remains on the dishes. The water softener is going throught salt like crazy. I fill the salt and make sure that the light is off before I start the cylce. Within the first 20-45 mins the salt light comes on again and the dishes will not wash properly. We have come to the conclusion that the salt is being distributed to quicky but cannot figure out why the light keeps coming on. The switch inside the cap for the salt is set a the min.


Just a thought, I hope the lady did not use table salt :-) ... Danby 17 in. DDW1802W Designer Series Built-in Dishwasher

Dish washer does not drain after the cycle is complete. The last few months when the dishwasher is done their would be a small amount of water left in the bottom. It didnt create any problems but would smell after a few days. So we would just run the drain cycle and it would empty. Well i got home to and the wife said the it was really full. The water was dirty and when you run the drain cycle it didnt drain. She said the dishes were clean. So i cleaned the vent, and filled the sink with


Check drain hose and drain pump.End of drain hose must be in same level with machine.Try it. ... KitchenAid KUDR01TJ Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1474 seconds