Having problems with your Dishwashers ?

Water heater states "temp exceeded" when trying to light

\015 The pilot is lit but the water is cold\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water heater states "temp exceeded" when trying to light


... Dishwashers

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

HDW101SS does not heat water. Heater element mearures 28 Ohms. Temp Limiter is N.C. Temp controllers TS50 & TS60 not found. On economy wash timer moves as normal then stops when red heater light should come on. If the timer is assisted one click it will progress as normal but no hot water.


Hi.If the temp limiter shows no continuity, there will be no voltage reaching the element contacts. The high limit is connected in series with the heating element. If the hi limit is open the element will not get power. Any technician wil ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Hobart LX30 Hey I just bought a Hobart Lx30 and we don't have a power source that can handle the 50 amp requirement. We got it at an extremely good price so we are trying to work around it. I was told that disconnecting the water heater would allow it to work in a standard 120 volt outlet. I did that and now I have another issue. The machine wont run unless the water is 160 degrees. How do i disconnect the sensor that restricts the temp so that I can run the machine at a lower temp?


Hopefully you took the suggestion to run the correct 50 amp 208-240 service to the unit.Converting the unit to an LX30C has a couple of pitfalls. The LX30C is connected directly to the incoming water supply, which should run 120-140 degre ... Hobart 24 in. LXIH-3 Built-in Dishwasher

We have a whirlpool quiet partner iii. It was working fine and was opened mid cycle. Then it wouldnt drain. Then all the lights started blinking. At some point it drained the water out. We flipped the breaker and now just the normal cycle light is flashing. Flipped breaker again that didnt work. Tried the reset code hi temp wash and heated dry. Normal light still blinking. Help please?


See this causes and fix it. God bles you\012 \012 \012 \012 \012 Check Fault Codes\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

Follow-up I've removed the lower arm, I'll spend some time and see whether I can get the pobem sorted out. My wife noticed the the detergent was smeared all over the door and repeated tries didn't get it out. Therefore, the water is not spraying. I can confirm the water is filling on the bottom and draining. The heater is working well. I am thinking there is no pressure to send the water through the tubing to the upper and lower arms. The motor is hot to touch (118 degrees with my temp probe). I


... Kenmore 24 in. 15199 / 15194 / 15192 Built-in Dishwasher

I have an electrolux slimline dishwasher model number esl 4115.On every cycle it starts with pumping out any excess water but will go no further.I have tried putting water in and all it does is pump out the water and continues with a humming noise.once opened the humming noise continues and the programme light continues to flash.there is another simble which is -] but with an arrow rather then a line that flashes 3 times.It seems to be stuck on empty.In the handbook it states that the anti-flood


... Electrolux 18 in. ESL4114 Slim-Line Built-in Dishwasher

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


... Dishwashers

Danby/Kenmore mode 461-14352. Some water is coming into the dishwasher but not enough to reach the heaters. Water not up to temperature, dishwasher will not start. Front temp light blinking


... Dishwashers

I have a Diplomat ADP 8242 dishwasher. When i select program dishwasher starts working but then beeps when opened no water has been brought into dishwater and program light 2 & 3 flashing 5 solid. Have tried reset and works like instructions states. But when I have re-tried dishwasher same fault happends again. Any help


... Dishwashers

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

My new bosch dishwasher doesen't clean the top rack of glasses, ran it 3 times, no difference. also the soap dispenser opens up but the powdered detergent won't dissolve, the same soap has been in the dispenser for 3 cycles. i turned up the water heater temp to try to fix the problem it seems to have no effect. the dishwasher is 2 weeks old. could my water supply line be too small or are they a stndard size. thanks


... Bosch Dishwashers

Purchased in 2003. Dishes were exquisitly clean till 2008. Our water heater temp was set at 140 temp. This heater was replaced with a heater now set at 125 temp. In the past two years dishes are nowhere as clean on the the normal start setting. Should I go to the Pots and Pans start setting to get hotter water or should I turn up my water heater? All this is assuming that water is not hot enough. Does the washer heating element ever burn out?


Try turning on your water at the sink for a while on hot let it run then start the wash cycle that should help. what that will do is let the cold water run out of the pipes and therefore you will have a hot water start. ... Kenmore Dishwashers

Kitchenaid dishwasher The clean light was flashing 7 times, so I did read and try the solution SaniRinse-EnergySaverDry-SaniRinse-EnergySaverDry and this did get the machine to unlock and start up. Thank you! But I'm noticing that no watre is going into the machine. I can hear it drain some water. It is very hot and steamy in the machine so no heater problem, but I don;t see any of the soap on the bottom of the machine rinsing away. I'm afraid its stopping because the motor is overh


... KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

Hi, I have a Miele G638 Plus dishwasher and the Red Inlet/Drain light comes on shortly after the wash cycle starts. I have cleaned everything out and the impellor moves freely. I have also made sure the outlet is clear. I have tried resetting and repeating on different washing cycles but it always locks out after the washing cycle starts. Could this be a heater problem as the element looks quite corroded? I have had side panels off and the water appears to flow easily through the sid


Hi\015\012\015\012Thanks for using FixYa. The first\015\012thing that should be checked is if its draining properly as it could be that\015\012the drain hose is clogged an ... Miele 24 in. G638 Plus Free-standing Dishwasher

My Frigidaire dishwasher does not seem to be "heating up". Have tried turning up the temp on water heater but it did not help.


Hi,Check your heating element.. Dishwasher ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I just bought a kenmore elite model # 13193 hooked it up ran it and it stopped mid cycle the detergent was released but not dissolved and the clean light keeps flashing. Ive reset it and turn up the water heater temp but still does the same thing.


You need to hand prime all new installs with a gallon of water first,Put it in then run cycle. ... Dishwashers

Hi I have a Bosch dishwasher model SGS43T72GB/09. It has been working normally until lunchtime today and we noticed water pouring out of the door. We emptied the water and realised that the fitler was blocked with grease. We have cleaned the filter and tried to reset it. There is no water in it but all three lights are on check water, active & end when we try to reset it. If we put it onto a cylce active light comes on and you can hear it doing something but its not filling with water. Can you


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Dishwasher will not fill with water... push start and the lights go out.. can hear motor but no water push again and the lights come on but no action inside i have tried 'cancelling; ... water is ON , door is closed.. have tried different cycles.. no kinks in hoses :(


Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher ... Maytag Dishwashers

De Dietrich Dishwasher - DVH 610 JUI - when turned on to any programme and started automatically tries to drain water instead of filling with water. Was disconnected and filters checked and were clean. when turned on again it worked and when disconnected to be brought back into house it again tried to drain water instead of filling. All lights come on except blue light. Does not accept engineer code given with wiring leaflet


... Dishwashers

Aeg bs45e water heater, heats water for 5 mins and then 'trip' light comes on and pressing reset button does nothing, heater must be turned off for 5 to 10 minutes b4 it will heat water again


... Dishwashers

Inlet/drain light on. i know it drains OK because if i pour water into bottom and close door and turn on i can hear it draining water out. it wont fill. i have cleaned everything and taken base off and cleaned and checked float and all ok. i have tried every combination of holding buttons down and trying to reset but machine just makes low humming noise and after about 5 seconds the red light comes on again.


... Miele 24 in. G646SC Plus Free-Standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1701 seconds