Having problems with your Dishwashers ?

Dishwasher Whirlpool adg 6966, light showing 20 mins even 4hrs and more after finishing

\015 I have a Whirlpool adg 6966 dishwasher. I turned it up this morning to wash the dishes, but when it finishied, the screen that showes minutes left showed 20 minutes. And it stayed there 4hrs after I started it! When I turn around the wheel for degrees it always shows 20 minutes, no matter what I do. I tried to reset it by shutting the power off and on, but nothing... Now I have cleaned the filter, resetted it and started it up again. It mumbled for a few seconds/minutes, then I turned it up again, and now it's working like usual. It's working empty. Can someone help me? I don't know what's the problem.\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher Whirlpool adg 6966, light showing 20 mins even 4hrs and more after finishing


... Dishwashers

I have a SE24T250 and the timer on the auto programme says 188 mins (it is usually around 120 mins) When the prog runs it doesn't finish and shows 1 minute to go and never gets to the drying or end of cycle part of the programme. Have tried the reset but it still shows 188 mins when complete. Any ideas?


... Siemens Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

Whirlpool Dishwasher ADG 9020 showes error code F6. What does that mean?


... Dishwashers

Whirlpool dishwasher ADG 7460 will fill with water ok and wash but will stop before it finishes the cycle leaving water in the machine. if you set it to rinse it will drain the water .... so the drain pump is working ..... water it drains is hot so the element seem ok ..... help


Hello & Welcome to FixYa Dishwasher not draining completely problem usually ... Dishwashers

Whirlpool adg7460 dishwasher. when i start a program runs for 2-3mins then beeps to indicate cycle has finished


... Whirlpool ADG450 Slim-Line Built-in Dishwasher

Whirlpool dishwasher ADG 7460 put on 30min programme - finishes early beeping start button green light flashing other light indicator now on pre rinse


... Dishwashers

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

Whirlpool DU900,09,10,11,15,20,30,DUL100 Hi, I'm not sure what exact model mine is, but those are the models listed on the manual. I opened the washer and the whole upper part of the wash tower was laying on the dishes! I took everything out, and began trying to think logically, and re-assemble the thing; nothing appears to be broken. page 17 of the manual is the only place that even shows this set up, but it's just a part description. As I am looking at the picture, I realize that the spray tow


... Whirlpool 24 in. DU920PW Built-In Dishwasher

North star eletric hot 2000 psi 3.5 gal per min oil pump had blown shaft seal. replaced with new pump. put small allen plug in return port. I have oil flow to the pump but none comes out port leading to burner even with shutoff switch removed and pump turning. Installed test gage 0 pressure. Took off bypass line and ran into can. pumps small amount of fuel into can that way but with uneven flow & small bubbles. nomatter what I do I just can't get fuel outlet port to burner. pump # A2VA-7116 pl


... Northstar Pressure Washers

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


... Whirlpool Dishwashers

Adg9020 F4 problem after 20 min, I get code F4 and diswasher stop's it is a Whirlpool Model: ADG 9020 Typ: NGPH


... Dishwashers

The program does not finish and just keeps runing with 1 minuite showing on the dishplay. even when i turn the mashine off at the mains, it makes no differance, it just keeps running and it does not stop. any sugestions please. jim.


You must change the module control .that will solve the problem. if this helps please give me a 4 thumbs up post. thanks ... Bosch 18 in. SRS45E02 / SRS45E08 Exxcel Slim-Line Free-standing Dishwasher

My whirlpool quiet partner 2 dishwasher the clean button keeps flashing even though the dishes are not clean. Will not reset and I don't think it finished its cycle.


Same with mine. ... Dishwashers

6th sense whirlpool dishwasher not heating water or finishing cycle showing f3 on display dishes seem clean but not spotless and wet becuase they are cold


Check thermostat and heating elementwires and timer ... Dishwashers

Adg 3962 IX showing fault code f2 with flashing


The machine has a switch inside that activates when a set amount of water is loaded.If this switch then breaks (switches off) during the wash the machine assumes that the water has leaked out.Run it through a couple of washes, check ... Dishwashers

Whirlpool ADP 7460 doesn't finished cycles, and screen flashes F4


... Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

Error code F7 on Whirlpool ADG 4966 M


... Whirlpool 24 in. ADG6340 Built-in Dishwasher

Whirlpool Quiet Partner Doesn't finish cycle


FIX YA IS A JOKE I WOULD LIKE TO BURY THE ************** WHO CREATED IT! ... Whirlpool GU2400XTP Built-in Dishwasher

Whirlpool ADG756/1 dishwasher stopping and beeping after 1 min


... Dishwashers

Phillips whirlpool adg 7750 dishwasher not completing cycle


... Dishwashers

My kuppersbusch igv659 wont finish the programme it gets to 1 min and wont complete cycle, keeps just throwing hot water around and will keep doing this until you swith off and reset the timer.


... Kuppersbusch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1086 seconds