Having problems with your Dishwashers ?

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


... Dishwashers

My DX303 is constantly bringing up error 30. I have had it apart, and there are no water leaks. If I pour water into it, it will drain no worries, however it seems like it wants to continuously drain with this error 30. Sometimes it will come good and go through its complete cycle hassle free, but it's not now. Any suggestions would be appreciated. Thanks.


... Dishwashers

We have a Whirlpool Gold Quiet Partner IV model#GU1500XTKQ0,the normal wash cycle starts buts just goes into hang mode @ 76min remaining and just continues to wash, is it the control panel or the timer circuit board, all lights seem to work on the control panel


I replaced the heater element on mine and that fixed the problem. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

My Whirlpool GU2200XTS Dishwasher will not run. The clean light is blinking. The heating element was shot. I replaced it, but still have the same problem. The fuses test on my multi-meter as being good. Am I missing something? Is there any way to test the circuit board? I am afraid that might be the problem.


... Whirlpool GU2400XTP Built-in Dishwasher

No lights come on at control panel on Kitchenaid KUDS01fl. Circuit Breaker seems fine (have reset it).


... KitchenAid Dishwashers

GE GSD5320 seemed to finish all light wash cycles. Then it began to beep, with the NORMAL light blinking. I hit RESET, but none of the other buttons worked. I threw the circuit breaker for this appliance and waited an hour. I Turned the circuit breaker on but now I get the NORMAL light blinking, even when the door latch is not engaged. No buttons work.


... GE GSD5320DBB Dishwasher

Humming noise i have a GE nautilus GSD2200 model which has not been used more than 4 years that is giving me trouble.  it's making a loud humming noise (the noise comes and goes, comes and goes) which seems to be coming from the motor area at the bottom of the unit.  I stopped it in the middle of the cycle, but the water seems to be stagnant at the bottom.  any suggestion on fixing the problem myself?


I have seen this SOOOOO many times in my 35+ years in the appliance repair industry.......it is very typical....here you are this is an answer I provided someone with the exact problem not to long ago..............This is a t ... GE Nautilus 24" Built-in Dishwasher

Dishwasher won't start. Clean light keeps flashing. I have tried cancelling a couple of times, and it goes through a 2 minute process and goes right back to the flashing clean light and not allowing it to start. I have already tried shutting off the breaker as suggested by someone but it did not solve the problem. Any other ideas?


Hi\015\012 \015\012Thanks for using FixYa. If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks t ... Dishwashers

LG LDF6810ST had OE error. Disassembled found no obstructions blew air through and vacuumed hoses to air gap and to disposer, no obstructions. Never heard pump run when starting cycle, so replaced drain pump. Still doesn't run. Looked at the service manual, and the only other suggestion is repair circuit? Is this the circuit on the bottom right of unit or the pcb up top? Wires and connections all look fine. What else could it be. Any suggestions appreciated!


Hi,Usually my First Response to this Common Error is :-Most likely pump trap is clogged up. Access it behind small door at front. Drain water out through small hose that is there otherwise water will be all over the floor when ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I have a Bosch Dishwasher about 10 years old, model SHV4803UC/U07. Yesterday it stopped working along with no lights on the selector buttons. I have reset the circuit breaker ( which did seem to not be off at any rate). It seem not to be getting any power if it's not the circuit breaker what else could cause this?


... Bosch Dishwashers

Is there a fuse or a circuit breaker in the Kenmore Ultrawash, quiet guard4 smartwash dishwasher purchased about 3-4 years ago? There is no power going to the machine--the outlet, the circuit, etc are all fine--but no lights light up on the panel and the washer wont start. Any suggestions?


There is a fuse behind the control panle its white and 1 inch by 1 inch ... Dishwashers

I have a magtag quiet 100 series that has a broken handle but still shuts tight and seems to lock yet. Problem seems to be that the rinse only light will stay on for quite a long time and won't let me hit the wash button. When the rinse only light does go off, if I hit the wash button it starts but then switches to rinse only. Sometimes I can get lucky and get it to stay on wash after the rinse button is off for some time. Any suggestions?


... Maytag 24 in. DWD1500A Built-in Dishwasher

How to reset dishwasher maytag MDB9601AWB? Tried depressing the button for 3-5 seconds the way the manual says - no good. "Lock" light just stays on. Tried unplugging. No good. Tried circuit breaker. No good.


Let the breaker sit off for an hour, if that does not work it needs help ... Maytag Jetclean III MDB9601AWW / MDB9601AWB Built-in Dishwasher

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

We have a Kenmore Elite Dishwasher #665.1646 - 5yrs old. On Friday nite, there were no problems but last nite the lights would not go on when cycles were pressed ( or Start). Checked the circuit breaker and it was OK. There is nothig caught in the bottom and the overfill float is functioning. I pressed Hi-temp and Air dry alternately and all the lights lit. I pressed Smart Wash, then Start and it did not go on. I can hear it draining but no water seems to flow and then it stops. All light t


The thermal fuse on the control panel. There isa couple of wires that lead up to a white box with the fuse in it. Thatis the problem. If you are good with a volt meter or light and youplace it across the fuse, if it is bad the light will light ... Kenmore Dishwashers

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

Amana dishwasher, model adb2200aws, ser #, 26650464e. history: quit running, no lights, nothing. replaced the door switch, ran for three days, replaced the switches on both sides of door switch, ran three days, quit. replaced the circuit panel , ran one time, quit. not lights, nothing. when I take it apart sometimes, that is take off inside cover on door, it might run or not. seems like the current isn't getting in as no lights will come one.


I have the same problem with mine as well but I found out that if you take a space heater to it and warm the control panel up for about 5 minutes, everything works great. This model of dishwasher seems to be problematic in any environment under 70-75 ... Amana Dishwashers

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Good Afternoon We have a Kleenmaid DW8 dishwasher. At the beginning of the cycle, it will pump out the water, sit idle for a short time and then show the end light, without washing or any further action. A technician came to visit and had a brief look. A follow up call came from his company stating that the circuit board had a crack in it. It would require a new circuit board ($650), the dishwasher to be taken to the workshop and repaired ($150). Upon further investigation, the circuit board had


... Dishwashers

Hi experts, My Indesit IDL530 dishwasher never seems to run on any of the 5 programmes. On pressing the power button, the red light comes on and on pressing the start/reset button, the light signalling washing comes on and not the one showing water intake. But even then nothing progresses and just a buzz with that wasing indicator on shows for a second and goe off. But today only the buzzer sounds when pressing down the start/reset button and no indicator comes on atll. Will be great if you coul


... Indesit Dishwashers

At 2 minutes left in the wash cycle, the quick rinse light starts blinking and the timer goes to 0. My dishwasher is a Whirlpool Quiet Partner IV gu1500xtkbo dishwasher. I'm assuming the blinking light is an error code. What does it mean?


... Whirlpool Dishwashers

Hotpoint BFI680 My dishwasher (hotpoint BFI680) works on occasions but more often than not goes on then it beeps and the 4th LED light ("eco auto") light is flashing. Water is getting through to the machine fine and ive tried resetting the machine - any suggestions?


... Hotpoint 23 in. BFI68 Built-in Dishwasher

Our dishwasher is no longer cleaning dishes very well and usually the detergent tab that we put in does not dissolve completely. Our dishwasher is a General Electric Model # PDN7800G00WW and several years old. The water here is very hard. On a separate note and a new development is the control panel seems to be messing up. When we press the ''speed cycle'' which is normally 37 mins it goes to 86mins and lights up the ''speed cycle:'' button. pressing the ''glass cycle'' lights up the adjacent '


Hi,\015\012\015\012There are various reasons for the Dishwasher not cleanig the Dish properly, From your query we can understand that, it must be issue with the Dishwasher selecter switch..\015\012\015\012DISHWAHER SELEC ... GE 24 in. Profile PDW7800 Built-in Dishwasher

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1471 seconds