Having problems with your Dishwashers ?

Candle in Dishwasher

\015 Thank you that was very helpful .. the model number is lg ldeg8812bb and i was unable to find a schematic but the link you sent did help...!\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, I washed a candle, yes candle, in my daughters brand new lg dishwasher and now it doesnt work. Surprising i know. After spending days tearing it apart and removing all the wax out of the inside as well as pipes and hoses, etc it will now do everything but drain. Can you help?


The problem is that when you ran a wash cycle.. the heater came on and melted the candle and some wax probably ended up in your pump or hoses in/out of that pump.. Since you did not provide a specific model number, I cannot provide specific details o ... LG Dishwashers

Candle in Dishwasher


... Dishwashers

I have a Bosch dishwasher model #SHU53A05UC/14. the control unit blew up, like roman candle, the 4th of july, the sparks the smoke, etc, is it still worth fixing? it's a 2002 or early model.


Hello, welcome to FixYa.\015\012 ... Bosch Dishwashers

I washed some small candle holders and they got stuck in the bottom of my dishwasher (Model TUD6710P) now I can't figure out how to get them out. I can remove the sprayer arm but not the parts below that where they are trapped under. Any suggestions? It looks like there is other garbage stuck under there too.


... Estate TUD6710 Built-in Dishwasher

I have a maytag MDB600AWW dishwasher. the top spray arm doesn't turn. it wouldn't even turn if i removed the to middle trays. I took the accumulator out and cleaned it. the fine mesh filters were clogged. unfortunately, birthday candles found their way into the machine sometime back. i cleared as much as i could. when i put it back together, the top arm would spin only when i had the 2 middle arms disconnected. It seemed there was an increase in pressure. i ran a diagnostics test and there were


First check to see if the washarm itself is clogged, if so clean it out.\015\012\015\012If the arm has a bearing it may be shot.\015\012\015\012You may have a clogged manifold on the output side of the pump. I sometimes run a ... Dishwashers

Dishwasher not draining, drying cycle error Electrolux ESF 4120


You didn't say what model you have, most dishwashers have a float switch inside to prevent over filling and subsequent flooding. If this switch is stuck, the dishwasher won't start. \015\012\015\012Open the door and look inside the unit ... Dishwashers

Dishwasher Normally, after the dishwasher cleans the load, it displays green light next to clean. Once the door is opened, the light goes off an dishwasher is ready for next load. But from few days, after opening the dishwasher door, the clean light does not go off, it remains lit. Dishwasher doe snot reset for next cycle. So, I have to go in the basement and trip the main power to dishwasher. That resets the dishwasher. This needs to be done before each cycle. Not sure how to resolve the issue.


Make sure that you do not open the door during the wash cycle. Wait until all the cycles \015\012are complete before opening the door. Especially don't open the door \015\012during the drying cycle. ... Dishwashers

I have a Fisher and Paykel drawer dishwasher and I'm wondering if there's a way to put a panel on it to make it look like and integrated dishwasher. It would need some way of the panel moving to start the dishwasher because the controls are located on the front. I plan on putting it in an Ikea Akurum that is 24" deep. The dishwasher is 22-9/10 deep, so that looks like it would leave some space for the dishwasher to sit back in the cabinet so the door panel could be flush with the cabinet. I'm no


Hmmmm...the first thing that comes to mind is to check out ApplianceArt.com. they have alot of panel options. I'm not sure if they have the integrated ones you are looking for but they have cheap options for everything else. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

I have a Bosch Dishwasher SHU3302UC/14 that will not drain. We initially thought the problem was the disposal because water kept backing up into the sink. We replaced the disposal, removed the dishwasher plug in the disposal, but the dishwasher still does not drain. I would like to check the drain line, but am unable to access it. I removed the kick plate and the screws that secure the dishwasher to the underside of the counter, but the dishwasher will not move. Can you access the drain li


... Bosch Dishwashers

I noticed water leaking underneath my dishwasher through the floor joists to my basement. It was a small but steady drip through the joists. I turned off the water to the dishwasher and the leak stopped. I looked inside the dishwasher and there is still some standing water inside the dishwasher, but I cannot see anywhere that water is standing under the dishwasher. I am wondering if the leak is at the pump or at the door? But I see no evidence of the seal leaking.


This is probably the line that goes from the water inlet valve on the bottom of the dishwasher up to the valve leading into the dishwasher itself. It is probably a black corrugated rubber line. This is an extremely bad design, but the solution is s ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I set my dishwasher to wash last night (delay 2 hrs.) and I checked it this morning and it never washed. Yesterday, I had to turn off the dishwasher at the breaker box because it wouldn't reset. Now, the normal wash and heated dry lights are on, but it won't start. Also, it usually beeps when I close the dishwasher door, and now it won't even do that. We bought the dishwasher about a week ago. It a GE Profile dishwasher. Thanks, Chris


\015\012\015\012\015\012First off all try to close the door tightly with your hand till you hear a beep.dont force very much.\015\012as you mentioned that unit normally gives a beep when door is closed.but not it is not giving that beep w ... GE Dishwashers

I'm installing an electrolux dishwasher, the first thing I'm going to do is the electric wire. I know I have to attach the black white and green (ground wire).I've done this before with my Maytag and it was a breeze. When I open the elec. box on the electrolux dishwasher the black white and green wires go into the box from the Dishwasher and then THROUGH THE BOX AND THEN BACK INTO THE DISHWASHER>>>>>THERE IS NO END........... In the Maytag I just opened the box on the dishwasher and the ends of


There should be a complete wire connection already there ready to be plugged in. If not, typically at the back of the unit there should be a black plastic box that when opened will indicate 3 terminals. live - neutral - and earth. Looks to m ... Electrolux Dishwashers

We have an ariston LS 620A dishwasher. For the last year every few months the dishwasher seems to cause a short in our electrical box causing all the power to go out in our house. It is only when the dishwasher is on that this occurs. We turn the power back on and everything, tv computer etc starts then turn the dishwasher on and everything shorts out again. We have had an electrician in who said that there was no electrical problem and that it was the dishwasher. After 2 months or so the dishw


The problem seems to be water seepage into the electrical contact.If the heater has lost its insulation this problem could accur( element to body )Disconnect the heater and give a try without any load and soap. If itperf ... Ariston Technologies Dishwashers

I have a Viking dishwasher made by Asko. It is less than 6 months old. Today I had a problem with my disposal (water not draining through it and leaking under the sink) and ran the dishwasher, which cleaned/dried the dishes fine. BUT, since the water was not properly draining from the disposal, apparently the dishwasher was not draining properly either. A repairman came to fix the disposal before I knew about the dishwasher issue. Now, the dishwasher won't turn off "draining mode" - button pu


... Viking DFUD042 Built-in Dishwasher

Nasty dishwasher there is nasty wet grunge at the bottom of the door, around the place the heating unit in the bottom of the dishwasher. half the time the dishes are clean in the bottom of the dishwasher. half the heating element is melted..for some reason...what do i do. the dishwasher still works, if we make sure the dishes are clean before they go in. using more for a sanitation thing than a dishwasher. can ya'll help me?


Sounds like your heating element is broken and you should replace it to prevent a possible fire hazard. \015\012You can replace the element easily for not alot of cash. You'll need to pick up a new one at an appliance parts store, just bring them the ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Bosch Dishwasher I currently own a Bosch dishwasher. One of the selling points, if I'm remembering right, of the dishwasher was it was supposed to super heat the hot water that is coming in from the tap. I have 3 problems. We have to rinse the dishes by hand before putting them in the dishwasher, Otherwise they won't come out clean. The dishwasher will run for four hours sometimes longer. It doesn't seem like it is heating the water any hotter than what comes out of the tap.


Your control board is bad. ... Bosch 24 in. SHU43 Built-in Dishwasher

Re: Bosch Dishwasher Model SHX46B06UC/14 (year 2003) Good afternoon, I have water dripping into my dishwasher when it is not in use, approximately up to 1/2 inch over a few hours. The water collects at the bottom inside the dishwasher. I have to shut off the dishwasher water supply so that it does not overflow. Other than that, the dishwasher works perfect! Any idea as to what has to be replaced? Can I do it myself or do I have to call a technician. Thanks very much for your help.


HI. This type of issue will be the result of mechanical failure. This failure will be within the inlet assembly. Debris may be keeping the solenoid valve from closing correctly, thus, producing the steady drip a ... Dishwashers

Water seems to be leaking into the dishwasher at the end of the cycle the water appears to be clean, so I am wondering about a seal of some kind on the hot water line leaking or whatever. It is a Bosch Dishwasher SHU series 3200 My problem is the same. Water leaks in to bottom of dishwasher over about a 2-3 day period. The dishwasher runs fine. It does not ever run over. The water seems to stop entering the dishwasher after it reaches a certain level.


You have a bad water valve. When the unit is off, the valve should seal and the water should not flow. Something has gotten in the valve and is keeping the needle up or the diaphram in the valve has deteriorated. replace the water valve and you wil ... Dishwashers

I have a Zanussi dishwasher model IT 5614. When I turn the dishwasher on, the indicator light is already stuck at "BIO 50" and won't move, and the dishwasher won't start when the door is closed. This just happened today. The indicator light for dishwasher salt was also on, so I added dishwasher salt and that light went off, but the machine is still stuck. The instruction book says that when this happens, technical assistance is needed. What exactly is the problem, and is it anything I can


It has been suggested to switch the machine on/off a couple of times and the flashing light will not reappear. Until this light goes off the dishwasher will not start. All the filters should be cleaned free of any leftover food particles. What i mean ... Dishwashers

Leaking Dishwasher seems to be leaking. Otherwise it's performing fine. I have laminate floors, and there are water seeping out along the seams of the flooring area near the dishwasher. The dishwasher is captured by the floor (dishwasher was installed first then floor was put in at 1/2" higher level), so we can't pull it out to check where the leak is coming from. Can dishwasher be repaired from the inside w/out removing it from where it is? Only way to pull it out seem to be cutting a part of


This is a huge problem for you. when you have a leak coming from the bottom of the dishwasher the machine will have to come out. but first check the door gasket to make sure the leak is not coming from there. ... Jenn-Air 24 in. JDB4950 Built-in Dishwasher

LG Dishwasher I just purchase a new LG Dishwasher. The installer told me that the dishwasher can not be flush to the Kitchen cabinets because of the metal cases around the dishwasher and also it can not be aligned with the top and bottom of the cabinets because the door is too thick to give it clearance to open. I have had two other dishwashers in this spot and never had any issue. Thoughts? Thanks, Jen


I can't say for sure, but it is possible this unit is deeper than previous units. The only way to tell for sure is to measure the previous unit and compare to this one.I would be suspect there may be something simple preventing the dishwa ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Whirlpool dishwasher This dishwasher quit in the middle of a wash cycle,we had to empty it and wash by hand. I thought that maybe the breaker to the dishwasher popped but when checked it had not .I then noticed that there are no lights on the electronic key board .Even when not in use there should be one red LED that is lit. It almost seems as if there is no power to the dishwasher. Is there some type of backup safety switch or breaker on the dishwasher itself that I could reset?


Fuse on control board. ... Dishwashers

Dishwasher Leak I found water on the floor in front of my dishwasher one morning so I removed the panel and ran the dishwasher to check for leaks and found none. I did check all the gaskets on the inside and they appeared okay. I again ran the dishwasher and had no leaks at that time, however, the last two mornings after I have found water in front of the dishwasher.


Hi,Here is a tip that I wrote about leaking dishwashers...There also is a link in there to another tip on how to buy parts online fo ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I was replacing my sink faucet today and in the process turned the water off to the dishwasher. Subsequently my girlfriend ran the dishwasher without the water on! Now when I go to run the dishwasher no water comes out (meanwhile I've turned the water to the dishwasher back on). Is there some kind of reset? I accidently touched the coil in the bottom of the dishwasher just after trying to run it and it was hot. What do you recommend? Thanks. Mark


Hi,You need to investigate the following :-\015\012\015\012\015\012\015\012\015\012Drain line/air gap\015\012\015\012A\015\012clog in the drain line or air gap (if there is one) is the usual reason\015\012that a dishwas ... Kenmore Dishwashers

Dishwashing liquid ( Cascade Liquid- gel- with Dawn) seems to be crytalizing is dishwashing reservoir on the door. After running the dishwasher the small door holding the liquid is open but still has some residual dishwashing liquid in and it seems to harden right away into a crytal like substance. Just started doing this. Is it the product or dishwasher? The dishes come out clean. This product doen't seem to clean as good as the first cascade. Thank you


Tide is having a problem with it freezing during shipping. Call for a free replacement. Or...to thaw it she said to put it in hot water in a sink for one hour, then do it again (not boiling...have lid on tight). ... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1052 seconds