Having problems with your Dishwashers ?

How do I run a service test cycle on a dishwasher Whirlpool ADP 6947 PC


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I run a service test cycle on a dishwasher Whirlpool ADP 6947 PC


... Dishwashers

I need to run a whirlpool dishwasher prima lpr600/1 service test cycle


... Dishwashers

How to run a test cycle on whirlpool dishwasher 7979


... Whirlpool Dishwashers

Our LG 6810 dishwasher has stopped cleaning. After the cycle the dishes are wet and covered in greasy clumps. We ran the test cycle and got the following: 3H/U3 11 22 33 44 55 66 04-2 32 33 0 (inlet valve) 35 36 37 38 23 (Thermistor) 3A 3A (beeped twice and showed 3A) 3A (beeped twice and showed 3A) Any advice you could give me would be appreciated. I have the service manual but have never done any type of dishwasher repair. I'd like to not have to replace this dis


1.) Take racks out of unit.2.) put both of the spray arms in the 12 o'clock position3.) Run the washer,once the washer has started wash cycle,open the door and ensure the spray arms have moved off of the 12 o'clock position. Write down re ... LG LDF6810 Built-in Dishwasher

My Whirlpool dishwasher stutters loudly during wash cycle. It's an intermittent thing, in the sense that sometimes when i run the dishwasher it doesn't do it at all. But also in the sense that when it does do it, it's for like a couple of seconds, then fine for a bit, then stutters again for a few seconds, fine for a minute etc etc. Sound is coming from inside, kind of like the power is turning on and off rapidly. It's a Whirlpool ADP-8540 Stainless Steel (Made in Germany)


A symptom like this is commonly caused by a failing wash pump motor. If you are having this problem and the dishes are not getting as clean as they used to, the motor is most likely the problem. ... Dishwashers

I have a Whirlpool Quiet Partner I (DU920PWKQ0) that the detergent dispenser door is not opening to allow the detergent out during the cleaning cycle. So, the dishes are not being properly cleaned. I do not regularly run a dishwasher cleaner through the dishwasher like some sites recommend. Is this problem more related to cleaning than mechanical ..... If it is a mechanical problem, can I take the door plate off the inside of the dishwasher and get parts if needed??? without a service vist? Than


... Whirlpool Dishwashers

WHIRLPOOL DISHWASHER ADP 4504 WILL NOT RUN ANY CYCLE


... Dishwashers

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

Model: Whirlpool ADP 4501/5 (4 years old) Problem: Dishwasher won't start wash cycle. Green light flashes 11 times. After adding a bucket of water to the dishwasher it runs normally. Checked the inlet valve and it appears to be fine. Filled the salt container and it solved the problem for a while but having the same problem again. Any suggestions would be appreciated.


... Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Whirlpool ADP 6835 dishwasher will not work and has f4 dispayed on the screen. Holding the start button clears the f4 and the timer for the cycle then runs but doesnt actually wash then after the f4 comes back


... Dishwashers

I have a whirlpool du1055xtsq3 dishwasher that is not working. Start button does not light and can not run wash cycle, but other buttons do light up when pressed. Can I fix this myself or do I need to put in for a service call? Thanks!


... Whirlpool Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

My 2008 frigidaire 24" dishwasher model #FDB1050REC is not washing during the cycle. I have run the test cycle and the tub is filling up and draining but no washing is taking place during the wash cycle. The dishwasher has an electronic control board and therfore no mechanical timer. I put test leads to check for voltage on the power leads to the main washing pump, which I have already replaced with a new one, and I'm only registering a low voltage of around 10 or 11 VAC. With the cycle off I'm


If you have replace the motor and this did not fix your problem then yes replace the control board ... Dishwashers

My WHirlpool dishwasher won't drain - basin is full of water. Machine starts and runs the drain cycle, but something is clogged. I opened up the bottom, and pulled off the drain hose to the disposal, and that had no water in it, so the clog is somewhere before the water gets to the hose. If I run the dishwasher drain cycle, it is not pumping water into the hose. What next?


The clog could be in the hose,or on up in the mouth of the drain,air pressure might dislodge the clog,or dissasible of the drain pan in the machine. ... Dishwashers

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

I have no power to the dishwasher. I tried the circuit breaker, flipped it. No lights on, nothing. It must have been running when the power might have gone off, may be the power surged or something and it wasn't able to finish running the cycle. I have taken out all my dishes and washed them by hand but I still have water standing in the bottom of the dishwasher. I am a mechanically challenged mom and my husband won't be getting home for two more weeks. The dishwasher is a WhirlPool Gold Quiet


First check and make sure that the units not on a switched receptacle(and is wired into this circuit(i know the dishwasher is "hard-wired",as in the unit doesn't have a plug on it,but it could have been wired into this switched circuit by mistake) un ... Whirlpool Dishwashers

I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Bosch SHU43C My Bosch SHU43C is stuck with the drain pump running. I ran the self-test and it gave me the fault code 4 wich indicates a filling fault. The washer is empty and all wash cycles display the correct number of minutes for the cycle. It counts down to 0, but the pump continues to run. Does this indicate a stuck float, or is the problem with the control board? Where is the float located? Are diagrams/pictures available on-line anywhere? I've done some searching, but haven't found any. R


My SHU43C is just over 3 years old. I had a similar problem recently. First, there were a few floods. Then, the Bosch only drained non-stop. Even when I used the Cancel Drain buttons the drain pump would run without stopping. When I ... Bosch 24 in. SHU43 Built-in Dishwasher

Whirlpool dishwasher Clean light is flashing which says check heat circuit. I've reset board a couple times and run diagnostic. Element tests okay. Light keeps going back to flashing when running dishwasher.


... Whirlpool DU1055XTS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2411 seconds