Having problems with your Dishwashers ?

Sandstrom dishwasher not pumping( showing up F2 ) not

\015 Water not pumping\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sandstrom dishwasher not pumping( showing up F2 ) not


... Dishwashers

Fagor lf-017s Hi, my fagor dish washer is showing an f3 alarm. f3 shows as a flood or not draining alarm in my booklet. However there is no remaining water inside the dishwasher. I have removed the dishwasher and checked the pump which is fine. The pump is running at the start of each cycle until thr f3 alarm steps in. Any ideas why the machine is still asking to drain when there is no water inside?


The water level float is stuck in the "UP" position ... Fagor Dishwashers

E3 Error Hi My dishwasher is showing error E3, which the user manual states "The appliance is not able to pump out the water.", however, other E3 error states a heating issue. The dishwasher does in fact heat the water but generates the E3 error after 10 minutes or so, then pumps out the water from the dishwasher. I'm a little confused as to what the issue is here and what part I would need to rectify the problem. Any advise you could give would be greatly appreciated. Kind regards


The E3 error is a result of water temperature not getting to a nominal value within a particular time. This could be caused by several factors like heater faulty, wash pump not working well, wash arms not circulating water as required. Need model nu ... Smeg Dishwashers

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle


... Bosch 607335 Water Valve Assembly For Dishwasher

SMU50e32SK dishwasher showing E06 in display after a few seconds. Dishwasher has one Main Power PCB and one control unit PCB in the front. Info: Main PSU PCB has been shifted due to overvoltage. All sensor checked, seems to be ok after this has been shifted. I don't think the induction motor(big pump) has been affected due to the relays in front. Could it be the Control PCB in the front or maybe the small drain PUMP. Well some of you properly now what E06 is referring to on this model.


... Bosch 24 in. SMU40 Built-in Dishwasher

SMU50e32SK dishwasher showing E06 in display after a few seconds. Dishwasher has one Main Power PCB and one control unit PCB in the front. Info: Main PSU PCB has been shifted due to overvoltage. All sensor checked, seems to be ok after this has been shifted. I don't think the induction motor(big pump) has been affected due to the relays in front. Could it be the Control PCB in the front or maybe the small drain PUMP. Well some of you properly now what E06 is referring to on this model.


... Bosch Dishwashers

I have An LG LD-14ATI Dishwasher, it starts, pumps water in, shows up with E1 in display and pumps water out. Can you please help and tell me what is wrong and why it is doing it. thank you


Hi there,\012Well It is probably Faulty Water Inlet ValveFaulty Water Inlet ValveThe water inlet valve is the device that meters water from the supply lines into your wash tub. On domestic washers, there are two lin ... LG Dishwashers

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Hi I have a Bosch dishwasher . The red tap symbol is showing . The little filter pump is spinning but not pumping . It continues to run when door is opened . Can you help please


Sounds like you have a water leak. The machine is fitted with a leak detection device that runs the drain pump constantly as a safety mechanism. If you want to look your self you will need to pull the machine out and tilt it back and if possibl ... Bosch 24 in. SHV55M03GB Built-In Dishwasher

My smeg d1612c dishwasher is stopping at the rinses cycle and not doing anything no fault code is showing. The dishwasher is heating up motor is rotating and pump is working. can anyone help


... Smeg DWD612C Built-in Dishwasher

Dishwasher takes in water and then pumps it out to drain, showing that the cycle is finished, the re-circ pump does not come on at all, any ideas with this problem. The Model is a Tricity Bendix TDF200


This is a control fault. you will need to replace the timer or control board. this will fix your issue. ... Electrolux Dishwashers

Hi. I have a 3 year old LG dishwasher. It will not drain. Display shows OE. I completely cleaned the drain assembly inside the DW. I checked the discharge line, it is completely clean. I disconnected the drain line from the air vent assembly at the sink and ran the DW, still will not drain. I disconnected the discharge pump wires and ran current directly, the pump works. I replaced the main control PCB, still will not drain. Please advise. Thanks


Measure the electric resistance of the Drain Motor. (Value should be 20-40 Ohms) If it is out of spec, replace it.\015\012\015\012Please reply with what worked best. Thanks! ... LG 24 in. LDF 7811 Built-in Dishwasher

Good Afternoon We have a Kleenmaid DW8 dishwasher. At the beginning of the cycle, it will pump out the water, sit idle for a short time and then show the end light, without washing or any further action. A technician came to visit and had a brief look. A follow up call came from his company stating that the circuit board had a crack in it. It would require a new circuit board ($650), the dishwasher to be taken to the workshop and repaired ($150). Upon further investigation, the circuit board had


... Dishwashers

I have an Asko DW1875 dishwasher (10yrs old) which has just recently started having problems. The initial symptom was that during a washing cycle, unit showed '1' and inside became very hot (melting some plastic cups/plates in unit). On further investigation (with diagnostic mode), the dishwasher is filling and draining with no problem. When circulation pump runs there is barely any water pressure in blades (just dribbles out) and water leaks into undertray via a plastic white tab near front (v


... Asko D1876 Dishwasher

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Dishwashers

My dishwasher has stopped mid cycle showing 1 minute left , when stopped and started again it now shows 28 minutes contantly, plus it continues to run (ie pump running) after the door is open. Any ideas ? many thanks Doug


Hey dcp667\015\012\015\012Dishwashers are incredibly durable machines. They can take years of daily use and in many cases, it's only a change in decor that brings about a replacement. Of course that doesn't mean things never go wrong with ... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

Hi - my Viking dishwasher has developed a problem where the pump runs continuously, whether the power switch is ON or OFF. After the power is turned ON, the troubleshooting guide indicates that there is too much water in the dishwasher. (One of the pot symbols on the display flashes continuously to show this indication.) I am unable to switch between programs, e.g., from quick rinse to pots & pans. I cleaned all the filters to no avail. I had to secure the circuit breaker in order to turn t


If you open the kick plate, you'll see the pan below the motor and check for leaks. The leaks will trigger the sensor to pump water out. Once you dry out the pan, the pump motor will stop and you should be able to reset the program. ... Viking DFUD042 Built-in Dishwasher

Sandstrom dishwasher ( showing up F2)


... Dishwashers

Dishlex global 450 _ how do i fix fill level time fault? displaying oF? Hi There, I have the above dishwasher and saw your advice on fixing fill levels - my display is showing the oF message and the pump to drain remains on whilst mains is connected. turning off mains does not clear message. holding eco button down does not clear message? is there anything else i should do in terms of removing parts to assist the process? I have cleaned out all of the drainage bowl and all is clear. i would pref


... Dishwashers

Hi, I've a Siemens Aqua Tech wsition 150 dishwasher which just keeps pumping out and not progressing any further, the display shows the letter "F". Help!! Gerry


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1887 seconds