Having problems with your Dishwashers ?

Sandstrom dishwasher ( showing up F2)

\015 F2 flashing and water in dishwasher\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sandstrom dishwasher ( showing up F2)


... Dishwashers

Sandstrom dishwasher not pumping( showing up F2 ) not


... Dishwashers

I am having problems getting dishwasher to restart after I interrupted a cycle. I have done the cancel cycle pressing Normal and Delicate together. The dishwasher emptied then showed a PF signal. Now is it showing a LE signal and all Front display lights are flashing.


You should be able to reset it by tripping the breaker and waiting about 10 minutes. Then reset the breaker. Best regards, --W/D-- ... LG LDF8812 Stainless Steel Built-in Dishwasher

Fagor lf-017s Hi, my fagor dish washer is showing an f3 alarm. f3 shows as a flood or not draining alarm in my booklet. However there is no remaining water inside the dishwasher. I have removed the dishwasher and checked the pump which is fine. The pump is running at the start of each cycle until thr f3 alarm steps in. Any ideas why the machine is still asking to drain when there is no water inside?


The water level float is stuck in the "UP" position ... Fagor Dishwashers

Our LG 6810 dishwasher has stopped cleaning. After the cycle the dishes are wet and covered in greasy clumps. We ran the test cycle and got the following: 3H/U3 11 22 33 44 55 66 04-2 32 33 0 (inlet valve) 35 36 37 38 23 (Thermistor) 3A 3A (beeped twice and showed 3A) 3A (beeped twice and showed 3A) Any advice you could give me would be appreciated. I have the service manual but have never done any type of dishwasher repair. I'd like to not have to replace this dis


1.) Take racks out of unit.2.) put both of the spray arms in the 12 o'clock position3.) Run the washer,once the washer has started wash cycle,open the door and ensure the spray arms have moved off of the 12 o'clock position. Write down re ... LG LDF6810 Built-in Dishwasher

When exterior breaker panel was replaced, my Frigidaire dishwasher (model FDB989GFC2) was accidently wired to 2 breakers and briefly took a 200v load. It started, then immediately showed a Power Failure code and shut off. The wiring has since been corrected but the dishwasher now shows no signs of life. Is it terminal or can replcement parts solve the problem?


Hi\015\012\015\012\015\012Thanks for using FixYa. You’ll need to check the following things--\015\012\015\0121. Fuse (blown or tripped).\015\0122. Check the wire fasteners at dishwasher junction box. ... Frigidaire Dishwashers

Frigidaire dishwasher shows an error code of ER uo after only a small bit of water runs into the dishwasher shortly after the hot water starts running into the dishwasher upon starting the dishwasher up.


... Frigidaire Dishwashers

Dishwasher is model DWD1SSE type11045 Initially the dishwasher leaked water on the floor On investigation the bottom tray under the dishwasher was wet The motor was wet Tested the motor which was fine although the capacitor on the motor impellor was dead. Replaced capacitor, now no water going around the spray heads so found the impellor inside broken. Replaced that. No hoses are leaking. Machine now works fine heats up etc etc but over fills and the E5 fault shows


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

We have just purchased an IQ100 SE26N250G Dishwasher and are having problems in setting the washing programme. We have followed the instructions in the leaflet but the dishwasher will on wash on 40 degrees and cannot be cleared or changed to any other programme. Also, the information in the instruction manual that accompanied the dishwasher is not at all clear and is rather confusing as it shows that to clear an existing programme you simultaneously press and hold the 2nd and 4th buttons out o


... Siemens Dishwashers

I had a mouse get into the under part of the dishwasher. He/she/it got trapped and died. The smell made us aware of the problem. I had to take apart the bottom of the dishwasher and take out all the tubes to clean them. Very messy... My question...I took care to note where all the wires went, but somehow did not take care to note where all the tubes go. Can you advise or show a schematic. I have a Bosch SHy56 stainless dishwasher.


There are no diagrams available of this - however using some logic - you can figure out the path of the water.A picture of the bottom of the washer would be helpful as well.Water comes in from the water inlet hose to the pump. ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My Thermador dishwasher DWHD64EP/54 does not get the dishes clean. We checked all the usual things--water to the dishwasher is hot, filters clean, spray arms working and not clogged, detergent cups working, proper amts of detergent etc. We find that no steam is produced during the cycles, we find that the when choosing a cycle and power boost incorrect cycle times are now displayed compared to previous usage when the dishwasher ran normal. Some of the longer cycles now show only 24 min


... Thermador DWHD64EP Built-in Dishwasher

I have a DS605 and DD605, F1 fault comes up everytime I try to cut the dishwasher on also water will emerge in it and the impleller floats up under the rack on the top dishwasher. Both dishwasher comes on the same time and make noise and the F1 with a little rench shows up. They said when the red light comes on the salt reservoir is empty. What kind of salt do I put in.Please advise


... Fisher and Paykel DD605HSS 23 in. Built-in Dishwasher

In my Kenmore elite manual {Dishwasher} Model 665-13109k901 it says to clean the ultra wash filter once a month. Where is it located in the dishwasher the manual doesn't show it. Please help me with an answer. My dishwasher is 6 months old.


... Kenmore Dishwashers

E3 Error Hi My dishwasher is showing error E3, which the user manual states "The appliance is not able to pump out the water.", however, other E3 error states a heating issue. The dishwasher does in fact heat the water but generates the E3 error after 10 minutes or so, then pumps out the water from the dishwasher. I'm a little confused as to what the issue is here and what part I would need to rectify the problem. Any advise you could give would be greatly appreciated. Kind regards


The E3 error is a result of water temperature not getting to a nominal value within a particular time. This could be caused by several factors like heater faulty, wash pump not working well, wash arms not circulating water as required. Need model nu ... Smeg Dishwashers

I WANT TO INSTALL TWO CABLES IN MY DISHWASHER DOOR, I HAVE THE CABLES, JUST WANT YOU TO SHOW ME A DIAGRAM AS TO WERE THEY GO, MY DOOR TO THE DISHWASHER FELL DOWN, THE CABLE BROKE, MY DISHWASHER IS OLD BUT STILL WORKS GOOD


... Dishwashers

Problem for Kenmore 24 in. 15992 Built-in Dishwasher Previously answered by Ginko but have not had any responses since June 18 and problem not solved. No water flow into dishwasher. Actual model is Kenmore Elite undercounter dishwasher 665.15982990. Float is not stuck. Worked fine for 10 years until mid May. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound when starting cycles, only a single electronic click. When cycle is canceled, motor does s


Hi.Sorry about your old query.If there is no power on black wire and no filling, then check and eventually replace the thermal fuse. The thermal fuse is attached to control board. If it is faulty it will read continuity, norma ... Kenmore 24 in. 15992 Built-in Dishwasher

We had a problem with our garbage disposal and it resulted with water leaking from our dishwasher. The disposal is fixed, I removed the excess water from the dishwasher. I tried to run the dishwasher empty to clean it. It runs but then the E-2 alert shows on the control panel meaning high water level. I read in the book that I may have to have a service person do some sort of a reset. Is this correct?


Contacted the company and they e-mailed instructions to fix problem ... Asko 24 in. 1895 Built-in Dishwasher

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

Kenmore Elite - 9 Year old Dishwasher - A circuit blew and the dishwasher stopped in mid-cycle and did not drain.... I reset the circuit breaker and "manually" took the water out of the dishwasher. When I push buttons to restart the "95" shows up for the normal cycle. However, when I push start the "95" becomes a "--". Suggestions???


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Dishwasher is showing low dishwasher salt soon after putting dishwasher salt. why?


Do not bother. Continue using the m/c. If the inlet water quality is good do not worry. This is a sensor sensing fault, even if the salt is fully loaded. If the wash quality is good without salt continue.Otherwise add salt at ... Indesit 24 in. D63 Free-standing Dishwasher

We have a MDB4651AWW dishwasher. It is very loud, we have the bottom front panel that seals the dishwasher at the floor but cannot figure out how to install it. One way it does not fit, the other way it won't let the door open and close properly. The noise is terrible and it has been that way for three years. We don't believe there is anything wrong with the dishwasher, figure the bottom panel will deaden the sound. can you show us how it goes?


... Maytag Dishwashers

I have the dishwasher model number FGHD2433KF, I have noticed in the last few that I have used my dishwasher no matter what setting I push after a few minutes it jumps to 99+.... Example a push quickwash and start it, the time that shows on the screen is 50, it counts down to 49 then it jumps to 99+. Every setting I originally set starts out at the right time that is listed in my book but then after a few minutes it jumps to 99+. Do I need to call service. I purchased the dishwasher in May of


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

Dishwasher does not seem to have power. I have a Kitchen Aid, under counter unit, 9 years old, model KUDS01I. I used it 2 nights ago with no problem. When I push a button, nothing happens, no lights show, etc. It is plugged into the lower half of a duplex socket with disposal plugged into the top. Disposal works, so the problem seems to be with the dishwasher. That also eliminates any issues related to breakers or ground fault indicators, etc. Is there a reset button on the dishwasher? Is there


... KitchenAid Dishwashers

ERROR :LG Dishwasher model LD2050SH switches on but show E1 error. Also shows Fahrenheit and not Celcius


... LG Dishwashers

Dishwasher not cleaning dishes indicator shows 199 min


Sounds like you either have a leak which has activated the flood safety in the base, you can check this by pulling the machine onto a towel and tipping the whole unit forward ie raise the back of the machine off the floor so it is pivoted on ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1650 seconds