Having problems with your Dishwashers ?

I have a GE dishwasher model GSD 3960 LOOSS, I found a 12 inch plastic tube in the bottom loose, Do I reattach it?, is this something I can do?


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a GE dishwasher model GSD 3960 LOOSS, I found a 12 inch plastic tube in the bottom loose, Do I reattach it?, is this something I can do?


... Dishwashers

Our Hotpoint Dishwasher Model HDA200X-73BA has two little white plastic pipe stubs poking out of the bottom of the dishwasher. During one of the cycles--(I don't think it is the drain cycle)-- some water is being released from one of these pipe stubs and then it stops and the other one runs some water. They each only run for a few seconds, but the water is just running on the floor. These little pipe stubs are about one half inch in diameter and project out of the bottom of the dishwasher about


Hello. go to the sears direct website, click on the blue link below, and enter your model number. ou can then access an excellent parts diagram which will show these stubs and what may be missing from them. Joe\015\012\015\012 ... Hotpoint Dishwashers

I have a hotpoint dishwasher model# HDA1000G00WH. until recently never noticed rinsed water not drained after washing/rinse cycle completed. water level just above the drain cover. i removed the cover to see if i might find something clogging the drain screen but found nothing. i removed the plastic water "return" line & it was not plugged. thinking about pulling the dishwasher out, disconnect the plastic line connected to the bottom of the dishwasher, then remove the "bowel-like" container wher


Take out the pump. You should find a broken rubber flapper indide blocking the outlet tube. Cheap to repair. ... Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher

My GE dishwasher does not drain. Model GLD5600N00BB. I have cleaned out the drain passgge and jiggled the air knob with no success. I have raised the flexible tube to 32 inches above the floor . Is there something that I can do to test the drain without having to run a full wsh cycle each time I adjust something?


... GE Dishwashers

I have a Kenmore dishwasher Mod. #665 17729000. When I opened it there was a plastic tube laying on toip of the contents of the bottom basket: it looks like it could be the feed tube of water to the top basket, but I could find no way of reattaching it. I have not been able to find a detailed drawing of the machine on line. Help please.


W have herebelow the link of your model with all parts layout which we believe will helpyou see how everything is put together and also you can order any part thatmight need to be replaced. Don't thing we need to describe a ... Kenmore Dishwashers

I JUST HAD THE BOSCH DISHWASHER MODEL SHX45PO5UC INSTALLED. THE BOTTOM PLASTIC KICK PLATE THING IS NOT FASTENED SECURELY TO THE UNIT. WHAT HOLDS IT SECURE TO THE DISHWASHER SO IT DOES NOT PULL OUT ABOUT 4 INCHES?


... Bosch Integra 500 SHX45M0 Built-in Dishwasher

Kitchenaid Dishwasher model # KUDS25SHBS1 has started making noise. Noise happens when unit is draining so perhaps its the same mechanism that houses the grinder. Can definetly hear a clicking as something spins around to drain the unit. I have removed the washing armature and plastic skirt around bottom and felt underneath the skirted area, but don't feel anything caught or jammed. Noise is getting louder as more draining cycles are being utilized (i.e. as we use the machine more). Anyone have


Looks like motor noise. Check the pump. ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

I have a GE potscrubber Dishwasher Model # GSD3630ZZ3WW it has been leaking from the bottom for about a week. I took the bottom off tonight and ran the dishwasher so that I could see where it is leaking from. It is not a hose but the leak seems to be coming from the back of the motor or pump fan where it goes into that plastic housing that attaches to the bottom of the dishwasher seems to be leaking in the very center of that housing where the motor shaft enters the housing. Water is just spray


... Dishwashers

Subj: ge dishwasher mod/gsd3960looss - 1yr 4 mos old. problem: will not drain only used 6 times. last use after cycle done, water remained. had to hand drain. removed cover and checked drain area, no debris found. drain tube is connected to disposal by clear plastic tube; no clog in tube. the sink drains are clear and the disposal works normal. dishwasher drain seems to be stuck in closed position. this model has the touch pad controls. any solution????


... GE Dishwashers

My 14 yr old Magic Chef Model DU4K seems to be leaking (it is dripping into the basement just under where the dishwasher is located). it started when the arm at the bottom of the dishwasher did not seem to be moving so my husband took off the bottom "grill" to see if maybe there was something under there preventing it from spinning. It started to leak when he put it all back together (the bottom arm is still not spinning)


Being 14 years old I dought if spares are still available for this machine personally at 14 I would rather replace the unit if you are not in a possition to replace it you could advise from your local appliance repairs as to weather parts are availab ... Dishwashers

Whirlpool Gold Dishwasher - GU2700XTSB The top rack of the dishwasher is not cleaning. The bottom rack dishes clean fine. There are no clogs in either the bottom or top spinner arms, the plastic tube feeding water from the bottom pump to the top rack spinner arm is clean, the spinner arms all rotate freely and do not bind. Water pressure is correct and water temperature is correct. There are no lime or hardwater deposits or clogs. What could be the issue?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

I don't have a model number right now, but the front door on my Admiral dishwasher is leaking at the bottom. I have changed the gasket inside the door panel at the bottom but it still leaks. This is a rental property and the renters did a job on this dishwasher. I was wondering if they may have pulled another lower gasket off that I didn't know existed. Something like a windshield wiper. The seal I changed was a foam strip 3 x 22 approx. Thanks for your time, Joan


It may not be the door that is leaking if this is an older admiral or whirlpool dishwasher the lever that holds the soap door closed has a little rubber seal that after time will let water in during the wash cycle it the runs down the inside of the d ... Admiral Dishwashers

Our Amana ADB1500AWW dishwasher leaks at far left and far right edges ( at bottom points) of the inside door panel due to a design flaw. ie - In the fully open position ( door in horizontal position) the far left and far right edges (at bottom) of inside plastic door panel are stressed beyond what the plastic can withstand consequently the edges of the panel crack as far as 3 inches from edge to inside. This crack is very small and cannot be seen until the panel is removed and then full insp


... Amana 24 in. ADB1500AW Built-in Dishwasher

I have a Kenmore model 665.15835791 dishwasher. I suspect that some plastic packaging has clogged the pump. I've removed the lower sprayer and the circular plastic cover that is held in place with 8 torx head screws. I'm trying to remove the black circular object with a 1 inch hex counterhold held in place with a screw with a 1/4 inch hex head. I have applied some torque to the screw first CCW and then CW with no results. I'm concerned about turning the head off of the screw. Which is the


... Kenmore Dishwashers

Hello, I have a Kitchen Aid dishwasher, model KUDS30IVWH3. The dishes have not been getting as clean lately, the bottom is decent but the top rack is not getting very clean. Also, when I open the door after the cycle is done, there's a bunch of detergent at the bottom of the door and on the floor of the dishwasher, like it isn't getting sprayed all over or something. Don't know if I have to check the water intake valve or if maybe the sprayers could be partially clogged.


... KitchenAid Dishwashers

There was a plastic dishwasher part lying loose in the bottom of my dishwasher this morning. Can't figure out where it belongs. probably inch and 1/2 round , 1/2 inch high. Top of spray tower maybe?


Probably the holder for the bottome rotating spray arm. Mine just broke off this morning too. Trying to locate parts supplier that isn't in the states and has a picture of the part. Don't want to replace the whole assembly which would be costly. ... GE Dishwashers

Re: Bosch Dishwasher Model SHX46B06UC/14 (year 2003) Good afternoon, I have water dripping into my dishwasher when it is not in use, approximately up to 1/2 inch over a few hours. The water collects at the bottom inside the dishwasher. I have to shut off the dishwasher water supply so that it does not overflow. Other than that, the dishwasher works perfect! Any idea as to what has to be replaced? Can I do it myself or do I have to call a technician. Thanks very much for your help.


HI. This type of issue will be the result of mechanical failure. This failure will be within the inlet assembly. Debris may be keeping the solenoid valve from closing correctly, thus, producing the steady drip a ... Dishwashers

Dishwasher GSD2030F03WWSA735136B Model Series number;Piece fell off inside front panel, making it impossible to turn on dishwasher at all..so I took off front panel screws, opened dishwasher and saw white plastic piece but can't find where it goes but it must have something to do with turning the knob to start dishwasher because the knob won't turn now..so it must attach inside somehow but I can't figure out where it goes...help!!


I think you need to get a new knob, write down the model number and make and take the pieces to your local domestic appliance supplier, there might be something similar in stock. Now I do mean the kind of small supplier that understands this kind of ... Dishwashers

I have Frigidaire model FDB130RGS3. This seems like a pretty cheap dishwasher that is provided by my management company. This is third dishwasher I've had in this apartment. The others have all broken. Now this one, which is less than 6 months old, seems to have broken. It does not clean the dishes. I removed the round plastic cover in the base of the dishwasher and the bottom of the dishwasher (sorry don't know how else to describe this) is filled with dirty water. I drained the water and tried


Hi,\015\012\015\012the round plastic cover in the base should just push back on, but you need to make sure it is correctly rotated before doing so. It should look like this:\015\012\015\012\015\012 ... Frigidaire FDB130 Built-in Dishwasher

I have a Frigidaire dishwasher, Model # FDB1050REB2, Serial # TH74114244. I push the start/cancel button and the washing lite just blinks, and nothing happens. There is also 1-2 inches of water at the bottom of the dishwasher. What can I do. I installed the dishwasher myself. It worked fine up to this point.


Sounds like the control panel has failed . but ck the drain pump for a plug . if it cant drain the the prosser knows and the flashing is the trouble code .. mm ... Dishwashers

I am having problems with my smeg dishwasher door. The machine is three months old. The bottom left hand corner of the door is catching on the outer wall of the machine and catching and cracking the bottom plastic drip tray. The model is SA8210w


This a faulty installation and adjustment of the door. Whilst it is not directly a manufacturers fault it should be covered anyway, as installation is generally by the distributor or the manufacturers agent.It is also generally condsidered under law ... Dishwashers

I have a KitchenAid Dishwasher Model #KUDS03FTSS0 for about 1 1/2 years. Within the past week I have noticed it being noisier then before. I pulled off the bottom panel and the noise appears to becoming from the middle of the machine, an area that is covered by a semiclear plastic case. It has this noise when it is turning the spray wheel inside. Can this be the motor going bad? I installed the dishwasher and marveled at how Quiet it was. Now it's not that quiet machine in the kitchen.


The motor is going out. this is a warranted part, so call for service and just pay the labor ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

Model SHU43C06UC a mouse eats a poliestirene circular piece like a float attached to the right of the bottom plastic base of the dishwasher under a grey plastic lever, now the DW runs but the cycle in the display doesn't make progress and it doesn't make any noise that indicates the water are running, help!, please advice!


Hi there sounds like your dw is in flood protection remove the poliestirene float compleatly and make sure the lever that sits on top of it is in the down position, hope this is of some help.\015\012\015\012pat no for new float is 165301 ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher won't drain. (Kenmore 3380957Rev A) It's been not draining that well for a couple of months, but then a couple of weeks ago, it just won't let the last inch of water out. --I can't see in the center area under the plastic to see if something is clogging it. --I tried running it on three different cycles to see if that changed anything (Pots and Pans, Normal, and Water Miser). No difference. It never seems to overflow, but when the cycle is over, it has a couple of inches of


The problem could be the pump, the drain hose or the timer. It will not drain if left to sit. The thing to try first is to put a cup of white vinegar in the machine and let it wash. This may remove sludge or scale blocking the strainer. 2nd take the ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2699 seconds