Having problems with your Dishwashers ?

Parmco dishwasher cycle - Dishwashers


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our dishwasher goes straight from rinse to the endwithout going through the washing cycle. How do I change the cycle? Have tried holding the button to change the cycle, but doesn't change. The dishwasher is a Parmco PD6-PSF/PD6-PWF.


It turned out that the pipe bringing the water into the machine had a kink in it. We pulled the machine out and straightened it. A dishwasher technician suggested we look to see if the pipe taking water away from the machine might be the problem, but ... Dishwashers

Parmco dishwasher cycle - Dishwashers


... Dishwashers

Parmco dishwasher E4 fault, beeps at end of cycle, litre counter problem, what does this mean,how to fix, Grant


Go to www.searshomeservices.com they can fix it ... Baumatic 18 in. BHD45 Slim-Line Built-in Dishwasher

Hi, have a parmco dishwasher with E4 fault at end of cycle, owners book says litre counter fault, any ideas , cheers


... Baumatic 18 in. BHD45 Slim-Line Built-in Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Candy CDI1012 Integrated dishwasher. When I turn on the dishwasher and start it - for some reason it can not go the whole way through the cycle. When I open the door the - programme light is flashing and water is still in the bottom of the dishwasher - ie mid cycle. The water will only drain if I put it into another program to drain away - but as the dishwasher was mid cycle - the dishes are not clean


Hello mm1973,It could be because of bad door latch switches / blown thermal fuse / blown or oversensitive control board. In all these scenarios, a dismantling of the machine is required. If you have no prior experience, I'd recommend get ... Dishwashers

My Thermador dishwasher DWHD64EP/54 does not get the dishes clean. We checked all the usual things--water to the dishwasher is hot, filters clean, spray arms working and not clogged, detergent cups working, proper amts of detergent etc. We find that no steam is produced during the cycles, we find that the when choosing a cycle and power boost incorrect cycle times are now displayed compared to previous usage when the dishwasher ran normal. Some of the longer cycles now show only 24 min


... Thermador DWHD64EP Built-in Dishwasher

My SHE4402UC/36 dishwasher malfunctioned all the lights were flashing and the machine was trying to drain. The guy came out and replace the control board. The dishwasher now read 199 on all cycles except the rinse and hold, the santitized light does not come when its done. The repair guy told me the count down timers were flakey on the the Bosch dishwashers and it would learn my dishwashing patterns in time. So 6 cycles later the dishes are still damp at the end of the cycle-the length of the cy


Well its not baloney but it is cheesey. normally changing the module is the cure but it has to be programmed correctly. bosch has a recall so check it out and see because the recall is free and the tech is suppose to know how to program it. go to the ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Problem for Kenmore 24 in. 15992 Built-in Dishwasher Previously answered by Ginko but have not had any responses since June 18 and problem not solved. No water flow into dishwasher. Actual model is Kenmore Elite undercounter dishwasher 665.15982990. Float is not stuck. Worked fine for 10 years until mid May. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound when starting cycles, only a single electronic click. When cycle is canceled, motor does s


Hi.Sorry about your old query.If there is no power on black wire and no filling, then check and eventually replace the thermal fuse. The thermal fuse is attached to control board. If it is faulty it will read continuity, norma ... Kenmore 24 in. 15992 Built-in Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

The dishwasher will start to cycle. I can hear the water begin to run. I hear a click and at the time the dishwasher should start to run the cleaning cycle. During the cleaning cycle the dishwasher will stop working. The dishwasher is silent. The timer will continue and the water will drain out at the appropriate time.


This is probably okay, you have clock like motions running the motor electric contacts. There needs to be a delay between some cycles or shorting will occur. The motor on some designs, for example. is reversed to pump out water. to have this work lon ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

I have a SHU3032UC BOSH Dishwasher for a couple of years now. Always worked as expected. Latetly, the dishwasher never stops. It looks stuck on an "unknown cycle"... The cycle dial stays at the "bottom" cycle (there's nothing written). If I turn it 1-2 "clicks", the dishwasher continues its work and ultimatly finishes with very good cleaning results. Once, I open the dishwasher when it was stuck in the "bottom" position, and there was hot watter at the bottom. Here's what I've tried so


Hello, welcome to FixYa.\015\012\015\012Based on you description of the timer not advancing I suspect the thermostat isn't satisfied when heating the water.\015\012\015\012The SHU 30** unit`s with a mechanical timer have very few if any, issues with ... Dishwashers

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

Dishwasher Normally, after the dishwasher cleans the load, it displays green light next to clean. Once the door is opened, the light goes off an dishwasher is ready for next load. But from few days, after opening the dishwasher door, the clean light does not go off, it remains lit. Dishwasher doe snot reset for next cycle. So, I have to go in the basement and trip the main power to dishwasher. That resets the dishwasher. This needs to be done before each cycle. Not sure how to resolve the issue.


Make sure that you do not open the door during the wash cycle. Wait until all the cycles \015\012are complete before opening the door. Especially don't open the door \015\012during the drying cycle. ... Dishwashers

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Kenmore Dishwasher My dishwasher fills with water and then stops. I hear the cycle timer continue all the way through the cycle. I pulled the screen off the bottom inside of the dishwaher and stuck my hand in the diswasher drain. Originally I felt and cleared what appeared to be a torn up rubber band. I feel a thin straight metal pin that I can rotate and I believe it causes the pump to rotate as well. Once I do that the dishwasher will run normally thorough a complete cycle...BUT I have to


If you have either dry bearings in the motor or sticky grease buildup in the pump bearing/seal, it can cause the motor to stick rather than rotate on startup. More likely to be greasy crud buildup. \015\012\015\012The best you can do without disasse ... Kenmore 24 in. 15149 Built-in Dishwasher

I have a bosch smu 2000 series dishwasher. it has always worked well with no problems but then all of a sudden a week or so ago, the water stopped coming into the dishwasher to wash the dishes. the faucet and all other water areas continue to work w/o problems (i.e. bathroom, shower etc). in attempting to use the dishwasher, the entire cycle seems to be working, i initially hear what sounds like an initial water discharge when the cycle first starts and during the entire cycle it sounds like it


... Bosch Dishwashers

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bosch built in dishwasher shu4302uc The dishwasher appears to run through the cycle but the cycle keeps running. I have checked the screens and they were clear. I have a Bosch Dishwasher SHU4302UC and I can't figure out how to cancel the cycle it's in. It keeps running and running. It pumped all the water out and the LED indicator are lit for the rinse/dry.


There is a recall on the control board of many of these models. I have written a guide to help. It is here. Look for the phone number near ... Bosch 24 in. SHU43 Built-in Dishwasher

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

I have a Kenmore Ultra Wash Dishwasher (Model Number 665.15634) that will not fill up properly. When I try to run a cycle (any cycle), the first thing the dishwasher should do is fill up with hot water. But in my case, my dishwasher fills for about 10 seconds, then stops. Then tries to fill again for about 7 seconds, then abruptly stops again. And this process goes on and on and on. The dishwasher never fully fills up nor starts the wash sequence properly. Once the dishwasher fills up, it


... Dishwashers

I have a Bosch SHX46A05UC14 dishwasher. The dishwasher is in a new home I just purchased. I tried to run the dishwasher on a normal cycle. However, when I push POWER and NORMAL CYCLE it makes a buzzing noise...and that's it. I opened the dishwasher and on the base of the dishwasher there was a screen that could be removed. I noticed that there was still some anti-freeze fluid in there (because the house was winterized). Could there be a simple solution to this problem?


... Bosch 24 in. SHU43 Built-in Dishwasher

When dishwasher is set to begin, sensor takes very long period of time. Cycles are longer than minutes indicated. Dishwasher fills with water but does not wash. Water then drains as though cycle is complete and moves to next cycle. Then the process continues. When cycle for drying is reached, much heat is given and occasionally it smells as though there is burning. A 82 minute procedure turns into hours.


... Kenmore 24 in. 16532 - Multiple Color Built-in Dishwasher

My 2008 frigidaire 24" dishwasher model #FDB1050REC is not washing during the cycle. I have run the test cycle and the tub is filling up and draining but no washing is taking place during the wash cycle. The dishwasher has an electronic control board and therfore no mechanical timer. I put test leads to check for voltage on the power leads to the main washing pump, which I have already replaced with a new one, and I'm only registering a low voltage of around 10 or 11 VAC. With the cycle off I'm


If you have replace the motor and this did not fix your problem then yes replace the control board ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1333 seconds