Having problems with your Dishwashers ?

My whirlpool Model GEW9878PW0 takes two cycles to dry


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My whirlpool Model GEW9878PW0 takes two cycles to dry


... Dishwashers

My Whirlpool dishwasher takes two hours to wash, not including the dry cycle. what is wrong with it?


There is nothing wrong with the unit if it is a electroniclly control unit they are programmed to run for up to 2hours or a little longer. ... Dishwashers

I have a Whirlpool Gold Quiet Partner III (Model GU1200XTKB0). I have used it previously on "Normal" cycle and I always keep it on Air Dry. Last night I used the "Pots and Pans" cycle and it seemed to work fine. But this morning the Air Dry light is flashing and if I press a cycle key the Rinse Only light starts to flash as well. Nothing works. I have made sure that the console is not locked. Any suggestions? I do not have a Heated Dry button, only Air Dry. Thank you.


... Dishwashers

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

Kenmore model 665.16509200 Does not clean very well and now dry cycle not working. Wash cycle takes almost 2 hours, and still dishes had gradoo and white detergent on them, even ones that were clean when they went in. The drying coil had plastic melted on it once before, so that could have caused that malfunction. I am not so concerned about that, it is the dirty dishes after 2 hours that is driving me nuts. The short wash cycle leaves EVERYTHING dirty, so I just quite even trying that.


... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

We have a Whirlpool Dishwasher Model ADP 5550 Condenser( made in germany) which we purchased in Australia. We have relocated to India and shipped it here. After connecting it and doing the necessary plumbing arrangements, the dihwasher is functioning but it does not complete the entire cycle. It only rinses and washes. it does not do the second rinsing and drying cycle. Is it possible to get an electrical diagram of this model as the consultant here feels that it may be an electrical loose conne


... Dishwashers

Whirlpool DU1145XTPPB7 Whirlpool DU1145XTPB7 model. Normal cycle light started blinking sometime during end of wash cycle. It will not do anything. Things I have already tried and not worked: 1. Unpluged and pluged unit back in. 2. System reset w/ heat-dry button, etc. Any help would be greatly appreciated


These dishwashers normally have a "Control Lock" mode.  It's in the manual.  It is provided for child safety.  It's often controlled by holding the "No Heat Dry" button for 4 seconds or more -- same procedure turns it on or off. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a Whirlpool model GU2400 Whirlpool Gold dishwasher and it will not start. There are no flashing lights just dashes across the time remaining box. I tried to push hi temp wash/heated dry 3x but it only allows me to hit it twice and displays 88 in the time remaining box. Then it says d3 in the time remaining box. It will then start running a drying cycle for 12 minutes. If I push cancel it won't do anything. I have to hold in cancel for about 30 seconds and it will drop down to 6 minut


... Whirlpool GU2400XTP Built-in Dishwasher

I have a whirlpool gold quiet partner 3 n the cancel button won't go off n the normal wash button won't go off either. I can do a quick wash cycle on it but then goes right to sani rinse afterward n don't shut off itself it just keeps on going. Solution? Is there a reset for it because I have an air dry button but not a heated dry button so I don't kno if I should push sani rinse/air dry two times over as opposed to sani rinse/ heated dry or if there's a diffrent solution for it. This all starte


... Dishwashers

My Whirlpool diswasher model GU1200XTKQ0, runs through the cycle fine, but the sanitized light flashes continuously after the cycle is finished. I know that this will happen if the dry cycle is interrupted by opening the door, but thats not the case here.


... Whirlpool 24 in. GU1200XT Built-in Dishwasher

I have a 1999 bosch SHU 4300 dishwasher given to me. It worked great for about two weeks. Now it takes for ever *3-4 hours* to complete a cycle (if it does). I have opened the door to see it filled with sudsy soap after this long. I have checked the hoses and they are not kinked. Once the cycle of cleaning is over, If I reset it manually, it will rinse the dishes and empty just fine. But I have to manually get the dishwasher to advance to the rinse and dry cycle every time now.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SHU43 Built-in Dishwasher

My intergrated whirlpool dishwasher two year old starts beeping prior to the rinse cycle with a sequence og two flashes on the start button. it is two year old model adg 7450


2 flashes indicates the flood sensor in the base has been activated.\015\012Either a seal leaking, or the sensor is faulty.\015\012\015\012Press and hold the start button until it stops flashing to reset.\015\012\015\012 ... Dishwashers

I have a brand new whirlpool DU1055XTV5 dishwasher, installed two days ago. After the cycle completes there is about 1/2" clean standing water left in the bottom. It is not just down in the well area, the whole bottom is covered with water. This is after running a normal cycle with no other options such as sanitize or heat dry. I called Lowes, the store that sold/installed it, and they said this is normal in new dishwashers to keep the parts wet. They said as long as the water does reach th


... Whirlpool DU1055XTS Built-in Dishwasher

Our less than 1 year old Whirlpool dishwasher model DU1145XTPQA is taking as much as 2 and 3/4 hrs. to complete the entire dishwashing (normal)cycle. This is much longer than it used to take.


Contact Whirlpool service immediately to get a service call scheduled before the warranty expires.\015\012Most dishwashers that begin taking longer to complete the cycle have a failed heating element but that also normally means th ... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

I have a ge dishwasher model GSD5211 purchased in may 2006. Water appears to be dripping from under the front ss panel to the bottom of thepanel. I cannot open it to check the source of the leak. Alo found that the leak occurs midway of the washing complete cycle. It also seems that the leak during a particular cycle. Not sure which as just two indicator lights stay on thepots and pans and heated dry. Please help


You may want to inspect the seal around the door to make sure it's not worn out or has some foreign material stuck to it causing it to not make a watertight seal during operation. If you don't see any problems there, then you should pull the machine ... Dishwashers

Model 665.16522000 Ser FR1257081 Type 286-1 60 amp 8533385 STD B Miser wash cycle is washing/rinsing . . . takes about 1 1/2 hrs!! This is waaaaay too long, eh? That doesn't include the dry cycle, either. Is the timer broken?


... Kenmore Dishwashers

I accidentally placed Jet-Dry...DISHWASHER CLEANER...in my brand new Whirlpool dispenser. I took off the cap and ran two cycles of water through the dishwasher. The dispenser is 3/4 full of the CLEANER fluid. How do I extract the fluid from the dispenser....:-O


Let me understand you correctly. Jet dry in your soap dispenser or soap in your rinse solution dispenser. The only dispenser that holds solution is your Jet dry drying solution. But if you put soap in the drying dispenser then the only way to extr ... Whirlpool Dishwashers

I have a Whirlpool model DU1055KJVQ1, Type 575-0 under-counter dishwasher which is less than 2 years old. In the last couple of weeks, it wouldn't start intermittently, and I would need to hit cancel on the keypad, and then restart. Now that doesn't work. When I try and start the dishwasher, it doesn't work. I press Normal for the cycle, heated dry for the Option, and then hit Start. The buttons light up for 20 seconds or so, nothing happens and then they go out. Any ideas?


... Whirlpool Dishwashers

My whirlpool dishwasher model #GU1500XTLQ1 washes my dishes fine but the dishes are never dry at the end of the cycle therefore the inside of the dishwasher is always damp and mold grows on the inside surface.


Make sure the heated dry is selected. ... Dishwashers

Whirlpool dishwasher model# GU2451, two years old. On any cycle, it counts down to 44 and won't go any lower. It sounds like a motor is constantly running when it hits 44. It will continue like this until I shut off the machine. What needs to be fixed?


Hi,Go to the house breaker box and find the breaker for the dishwasher.Turn the power off form the box for 10 minutes and this will reset the system.This should usually clear any electronic glitches and enable you to start. ... Whirlpool Dishwashers

This is a "ventless" system. Our dishes aren't drying in any cycle. There are two door gaskets on this model, one was installed by me under the countertop. I was sure to make as complete a seal as possible, since I did not see a vent on the door itself. What can I do to fix this problem?


If your dishes are not drying properly, you most likely will have a defective heating element. You can remove the element on a General Electric appliance, (or any other make and model) and replace it, by following these simple steps: 1. Your heating ... Dishwashers

I have a brand new Whirlpool dishwasher #DU810SWPU4 - Model #. No instruction manual was left with me, so I want to be sure I'm using it correctly. When I run it and set the drying cycle to Heat - after it shuts off and I open it up, there is still water on the door and on some of the dishes. Is this correct? Jane Walker


... Whirlpool Dishwashers

Hi there...anyone home ??? My dishwasher is a Whirlpool Model # GU940SCGB2. What's happening is that when I start it. It'll start up run a minute or two....then it will stop. It repeats this all the way untill the end of the cycle and I end up with NO clean dishes and dishpan hands. Any ideas on what's wrong ???


Looks like micro-controller fault.You may have to replace this. Check with the manufacturer'sservice center. ... Dishwashers

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1632 seconds