Having problems with your Dishwashers ?

The CLEAN light is flashing on my Kenmore QuietGuard3 , but it won't clean anything. It starts a cycle for a few minutes, stops and starts flashing clean again. Any suggestions?


Answers :

You will have to reset the dishwasher. First try and turn off the mains power and back on after a short time. If the clean light flashing starts again then you go through the hard reset procedure.

press NORMAL WASH then HEATED DRY buttons one after the other until all the lights on the board lit up (3X's). The dishwasher will enter into a cycle; Press Cancel. This should stop the flashing.
If you are supplying dishwasher from hot water inlet then make sure the inlet water temperature stays within the recommended range of 145 deg F.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The CLEAN light is flashing on my Kenmore QuietGuard3 , but it won't clean anything. It starts a cycle for a few minutes, stops and starts flashing clean again. Any suggestions?


... Dishwashers

The CLEAN light is flashing on my Kenmore QuietGuard3 , but it won't clean anything. It starts a cycle for a few minutes, stops and starts flashing clean again. Any suggestions?


You will have to reset the dishwasher. First try and turn off the mains power and back on after a short time. If the clean light flashing starts again then you go through the hard reset procedure. press NORMAL WASH then HEATED DRY buttons on ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have F&P DD603 with problem with bottom draw. Once a programme is selected and door is closed, the dishwasher beeps three times then tries to start itys cycle. It then starts but stops every 1-2 minutes (like pause botton has been pressed). If you press start again it starts for 1-2 mins then stops again. I have tried turning off the power and totally cleaned out the dishwasher but no change? Any suggestions?


Hi \015\012When you pull out the drawer, pay attention to the bottom near the bottom front panel, you will see a little tab. this tab is at both sides of the drawer, press these tabs in and pull the drawer fur ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher

DISHWASHER STOPPING I HAVE A WHIRLPOOL ADG 7560/01 DISHWASHER. AFTER 4-5 MINUTES IT STOPS AND HAS A CONTINUOUS BEEPING AND THE START LIGHT FLASHES 4 TIMES THEN A PAUSE etc. I HAVE CLEANED THE FILTER LIFTED THE MESH AND CLEANED THE BOWL OF ANY DEBRIS AND WATER. I HAVE ISOLATED IT FROM THE ELECTRIC SOURCE LEFT IT FOR 10 MINUTES AND STARTED IT AGAIN TO FIND IT DOES THE SAME . LOST IS THE WORD THAT SPRING TO MIND. HELP!! MARTIN


... Dishwashers

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

It has been flashing an F2 error code and the timer starts at 65 then switches to "1" which stays on during the cycle. Now it will run for about a minute then stops completely. Can you suggest any parts that we can get to fix this?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012The "F2" for Asko dishwashers indicates either the unit is overfilling, or the valve itself has failed.\ ... Asko 24 in. 1895 Built-in Dishwasher

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

I have an asko D3450 dishwasher. Washer makes buzzing/humming noise at start of cycle and then randomly through cycle. I checked the sump and pump appears to be clean and impeller spins freely. The cycle seems to work ok. Water is pumping out ok. If you open the door to stop the cycle, the buzzing will continue for a few minutes then stop. If the cycle is restart, the buzzing starts again. The vibrations seem to originate from under the lower spin arm.


If the sound is a bussing - it is the capacitor mounted to the pump. It is failing.Shown here (big white cylinder on right of pic).. ... Asko 24 in. D3450 Dishwasher

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

We started the dishwasher and it started. during the cycle, the soap dispensor didnt open and now it flashes clean. I've tried to cancel sequence, it goes through the draining process but when I go to start, the start button flashes as does the cleanned button. Any suggestions as to hw to reset it. Thanks


... Sunbeam Dishwashers

We started the dishwasher and it started. during the cycle, the soap dispensor didnt open and now it flashes clean. I've tried to cancel sequence, it goes through the draining process but when I go to start, the start button flashes as does the cleanned button. Any suggestions as to hw to reset it. Thanks


Hi\015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allow the door to open. Th ... Sunbeam SNB542UCAS Built-in Dishwasher

Dishwasher cycle starts briefly for a couple of minutes and then stops again and the standard wash and eco wash programme lights are then flashing together? It appears that water is drawn into the appliance for a short time and it then seems to start and empty itself before the above lights start to flash, all within 3-4 minutes?


... Hotpoint 23 in. BFV62 Built-in Dishwasher

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

Dishwasher won't start. Clean light keeps flashing. I have tried cancelling a couple of times, and it goes through a 2 minute process and goes right back to the flashing clean light and not allowing it to start. I have already tried shutting off the breaker as suggested by someone but it did not solve the problem. Any other ideas?


Hi\015\012 \015\012Thanks for using FixYa. If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks t ... Dishwashers

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW


... Dishwashers

My Miele intake/drain light is flashing. It seems to be an intake problem, because water drains out fine, but seconds after water starts going to the machine, it stops and the intake/drain light starts flashing again. We've cleaned the filter in the inflow hose, cleaned the arms, and it still doesn't work. Any suggestions?


... Miele Touchtronic G892 Built-in Dishwasher

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

I have a modulogic ADP951.seemed to be stuck on cycle today so I stopped it. water did not drain. I cleaned all rotors and filters and re started. Water drained however start light now flashing. Have tried holding for 5 secconds to re start but only starts pumping out water (of which there is none) and then stops. Light continues to blink. Any other tricks??


I am assuming you have not tried the reset by turning mains power off and then on.\015\012\015\012One of the reasons for being stuck in the wash cycle is the water temperature is not reaching the right level. This could be due to heater ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

When I start the dishwasher, it sounds normal. A few minutes after it starts, it makes a loud, thumping noise that lasts for several minutes. After a while, it stops making noise, but about half way through the cycle, it starts making the loud, thumping noise again. It's loud, annoying, and does not get our dishes clean. We have to wash several dishes by hand AFTER we have run the dishwasher.


I have made the assumption that your d/w is a siemens machine, however if not pls repost with the make and model.\015\012There are a few possibities...check the spray arms are clear by removing any blockages in the holes, check that there ... Dishwashers

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

First 2 weeks ago i put an electric control module into the upper section. what comes on is the green flashing light for clean. in checking connections i found the paper for trouble shouting. i did what they said to do. they said hit the time saver - high temp - time saver - high temp. from there all the lights went on & the wash cycle started and ran. then it just stopped & the green light for clean just flashes. the water is still in the bottom & won't drain.


The error indicates that the machine has taken too long to drain the water. Do the following.\015\012 \015\012\015\012Switch off the machine, unplug or disconnect the ma ... Kenmore 16874 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2044 seconds