Having problems with your Dishwashers ?

Help me No water turns on just no rinse


Answers :

If you have water for washing the dishes and only the rinse water will not flow then the problem is likely a defective timer control. The timer send signals to the washer for all of its basic function to start and stop. Bad timers are a common problem, especially with an older machine, but they can also go bad in a new machine. f the dishwasher is under warranty follow the warranty service steps to get local free repair. Otherwise you may have to purchase and install a new timer yourself or hire someone to do this at an appliance shop.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi. Our DS603I dishwasher starts on the Rinse cycle on its own - it beeps, red light flashing and no water entering the tub. It does this even if it is open. Similarly, when we try to turn it on to do a normal or heavy cycle, it starts (making quiet a loud noise) and then goes to the Rinse cycle, beeping, red light flashing, no water going into the tub. The pump wheel is turning. We can't find any blockages in the tubes. We have power-cycled it many times. Please help!


Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012\015\012\015\012\015\012 ... Fisher DS603W / DS603B / DS603I Dishwasher

Our dishes smell like vomit after they have dried. We run them through the dishwasher, they seem to smell okay. Then when Dry, the smell returns. We have tried vinegar and tang rinses to no avail. We have turned up the heat of our water to scalding, that hasn't helped. We have disconnected drain hose and there is no smell there. What can we do to get rid of this awful smell? There is no food in any filters, heating element is clean except for some hard water stains. We have a whirlpool 575-0 qu


... Whirlpool Dishwashers

Crystal wash and rinse only buttons flash and can't get any other button to work. Tried turning off circuit breaker and holding down set/cancel button but goes right back to the two buttons blinking, also in this mode dishwasher makes sounds but no water. Help! Thanks.


Without a model number this is my best attempt at trying to help you with out it. In the bottom of the tub look for either a float assy or a finger like thing sticking up from the bottom. If there is a float gently push it down first ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Kuds011. not pumping enough water in wash & rinse cycles to turn sprayers. top filter is clean. Thanks for any help.


... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

Dishwasher runs full cycle, however, the dishes and glasses have small particles of food dried on them when done. I do rinse all plates and utensils before turning on. I run on a normal cycle, no heat dry. I use cascade action paccs 4X concentrate. Which appears to not disolve completey, the packet. It normally does. There is no water back-up in sink, and I also open the trap ,no blockage. Please help, Dan


Hi Dan and welcome to FixYa, I am Kelly \015\012\015\012 Most of the time when you start having dirty dishes post wash there is either an internal blocked screen under the lower wash arm tower or a problem with the drain. ... Dishwashers

I added 3 cups of water to the dishwasher DD24DT top drawer as directed to check the rinse cycle. I pushed the start/pause button, I hear some noise, but the dishwasher does not completely turn on., there is an icon with two arrows, like a cycle symbol. I did not get a manual with detailed instructions so need help!


... Fisher and Paykel DD24DT Builtin Dishwasher

Help me No water turns on just no rinse


If you have water for washing the dishes and only the rinse water will not flow then the problem is likely a defective timer control. The timer send signals to the washer for all of its basic function to start and stop. Bad timers are a common proble ... Dishwashers

Hi i have just purchased a hoover HEDS 668-80 dishwasher. Unit all plumbed in and salt rinse aide etc added. Go to turn unit on and all four lights flash with a alarm tone bleeping. The manual says - overfilled / too much inlet water. can anyone help with this problem as my dishes are now stacking up! many thanks jon


Turn down the house water valve. So not so much pressure is going through.If this doesn't help, which I believe it should, then I would take it back or have the water inlet valve on the machine checked to make sure it doesn't have a bad solenoi ... LG LDF6810 Built-in Dishwasher

We have a hotpoint aqaurius dishwasher df23n. When put on wash 4, the timer stops half way through and has to be helped. When the programme then continues through the rinse cycle, it stops half way through. I have tested the water heater and thermostat electrically and they seem ok. Is there anyting else that stops the timer at these positions? The timer knob is free to turn and is not jamming? Steve B


... Hotpoint Dishwashers

Hello, I would appreciate if you have any suggestions regarding my GE dishwasher. It turns on and seems to want to work but the rinse cycle does not produce any water, it makes noises like the water is coming out and rinsing but when I open the dishwasher the dishes are not wet. I've checked the water valve, turned the control panel off and on, I'm wondering if it is just clogged, any suggestions? Thank you.


Hi,\012Here is a tip that will help you to find out why water will not come into thedishwasher... Dishwasher Trouble No Water entering Dishwasher ... Dishwashers

I have a karcher 2.o1 pressure washer does not work when i turn the water on, if i turn the water off it works, cant figure it help , help please


Please try without the high pressure lance on. If this works then you may have a blocked jet in the lance. ... Karcher 2500 PSI Pressure Washer

I have KitchenAid dishwasher KUDS01FLSSD. The sani-rinse butten keep flashing and not let me start the machine. Other buttens are not working. When I push the sani-rinse butten with cancel butten with door closed, it makes sound that water is drainning, but there isn't any water in it! I tried 'sani rinse' 'energy save dry' 'sani rinse' 'energy save dry.' didn't work. Sani Rinse keeps flashing. Help me!!!


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Water I have a brand new house with all new appliances. I went to turn on my dishwasher and it comes on but no water. I turned on the valve under the sink but I still do do not get ant water... Please help.. Steve


Reach inside your d/w and jiggle the mushroom shaped float switch located on floor of d/w. should move freely up and down if its stuck up(or something lodged under it your unit wont fill with water ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

When the water should be filling or rinsing the machine is making a horrible, loud, noise and no water is coming out. The solutions I looked at for no water don't mention this noise - they mention a slight hum. This noise is as loud as a TV turned up almost all the way! This happened during a cycle - the wash ran fine and it got to the rinse and started this.


Hi,If the noise lasts beyond 2 minutes at a time (which it sounds like it does) then you have a motor problem. I am suspecting that the main seal has leaked onto the motor and is causing water to get into the motor. ... Maytag 24 in. MDB4100 Built-in Dishwasher

I have an Indesit IDL 42 dishwasher. It has entered a state in which it behaves like this: as soon as I turn it on, it starts swishing the water around (it doesn't pump it out) and it does that regardless of whether I press any buttons (I have tried Start, Reset, turning the program knob, no difference at all). When I open it in the middle of this cycle, the water drips, and there is plenty of water (about 1 in) at the bottom. I have checked the filter, it is clean. Can you please help?


... Dishwashers

I need a diagram and fixing help for a miele G892 SCU plus. The dishwasher starts up with the intake draining light blinking and the saltpc light on. Then the start stop button turn green on. It sounds like it is filling with water but a few seconds it stops and turns off. I open and no water is filling. I believe it is the water pump, what do you think? How do I install it?


... Dishwashers

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

Model #363.14232100 dishwasher. When you turn the switch to on, it will not come on. If you keep turning the knob slowly you can hear the dishwasher trying to start up,but it doesn't. Keep turning the knob and its the same thing, sounds like it will start, but it doesn't. It did fill with water, but once it was opened it didn't start up where it left off. The lock switch was in position, and still nothing. Now I have water in the bottom but can't get the thing to come on. Any suggestions? Help!


... Kenmore 24 in. 16539 Built-in Dishwasher

My Bosch dishwasher keeps on filling with water. It won't turn off. I had to turn off the water source to it for the night. Please help. I have a large family and rely on this appliance every day. Thanks!


The problem that you described should be the float switch. It could also be a defective fill valve (stuck open) ... Bosch 24 in. SHU43 Built-in Dishwasher

Our Bosch dishwasher #SHU9922UC (FD8007) will not turn on properly. Only its drain pump starts -- and keeps running -- when it's powered on and the door's closed. Pressing the two "drain cancel" buttons for more than 3 seconds doesn't help. Neither does cutting off power, then turning it back on in the hopes of resetting the machine's 'computer'. No water inflow occurs. Help?


I had a similar issue after I replaced a bad drain pump, seems the logic got hung up.. I poured in a pitcher of water, closed the door, it drained and was then ok - worth a try. If not, you may have a bad water level switch. ... Dishwashers

Our 8 year old integrated 2 draw dishwasher (top draw) has a problem on the rinse cycle and constantly beeps and water at the bottom of the draw remains. I have cleaned out all the grit and stuff residual water and tried to use again. But alas there appears to be a blockage still on the rinse cycle. Can you help or do I need to get a plumber? Thanks...Louise


Sorry i lost you my breaker tripped ... Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

HELP!!. Have an old smeg dishwasher - SNZ10. We turn it on, and it goes, but the dial never moves on through the cycles - it just stays stuck wherever you have turned it to. Does seem to be heating and water coming in. Husband grumpily doing dishes by hand! HELP!!


After a while thje dial on Dish Washers, wear out and jam, It sounds like it needs a new Timer, However if it's old, I would replace the Dish Washer. ... Smeg CSU2001 Built-in Dishwasher

The dishwasher fills with water to the level of the heating coil, when the wash clyce starts it pumps water but not enough to turn either spray bars. I have changed the chopper and wash impeller, cleaned the filters and float assy. Changed all the seals but it will not turn the sprayers. Help??


It sounds like a serious loss of pressure. I have a couple of question for you that will help me assist you.Can you get me the complete model number from the tag just inside the door?Does any water leak on the floo ... Kenmore 16632 Built-in Dishwasher

501ht goes thru wash cycle but cam stops just before rinse cycle clicks in - stays in wash cycle - turned thermostat to booster down in temp -cam then keeps going properly but with no hot water from booster - replaced thermosat still same result - apparently a safety ? no booster water no rinse?


Did you get a solution for this? I am having the same issue. Please email me at [email protected] Thanks -Eric ... Moyer Diebel 24 in. 501HT Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1459 seconds