Having problems with your Dishwashers ?

How long before cycle is done

\015 How long does it take to cycle\015

Answers :

Normally around 30 to 45 mins
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How long before cycle is done


Normally around 30 to 45 mins ... Dishwashers

Completed solder proceedue about 2 months ago. worked ok till now. Now same symptom has occured. no heated water, long wash cycle. Maybe the board or attached relay are done?


Hello\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your post, the solder may not have been sufficient to hold, or as you alluded to, the relay itself has failed now.\015\012\015\012The best thing to do ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a bosch she5al06uc/05 and it seems to run for a long period of time. I end up manually shutting it down. It doesn't make any sound indicating that the cycle is done and I have tried resetting it to the default settings with no success. I'm not sure wat exactly is suppose to be flashing wen in the control panel either. any help would be appreciated.


Hello,Welcome to FixYa.Based on your description I'd say the issue is with the control...unfortunate ... Bosch SHE5AL06UC 24 in Builtin Dishwasher

During power scrub cycle which is the one we use most of the time the dishwasher stays at one minute fot a long time. the dishes come out clean and it finally does finish cycle just dont know why it takes so long on last minute of cycle for so long


It's just heating the water more ... Bosch 24 in. SHU43 Built-in Dishwasher

My dishwasher runs 2 hours as a complete cycle. I think it is never going to finish but I have not stopped it in mid cycle. Dishes are very clean but they should when it runs this long. I hear it change cycles so I know it is not stuck on 1 cycle. It also makes a lot of noise. 2 hours of noise. HELP!!! How long it it suppose to run?


That means that the machine does not detect that one condition to continue the cycle is met.Sometimes\015\012 when this happen unesperience repairers replace the timer board , an \015\012expensive part that rarely fails. The timer b ... Whirlpool DU1055XTS Built-in Dishwasher

My dishwasher Siemens work corectly only on 30min cycle.When i use the other long cycles (cycle is very long ,more than normal for cycle)and their is water at the bottom of dishwasher at the end.Model : SL65560EU/21


... Siemens Dishwashers

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers

Bosch SHX56B05UC wash cycle is very long and water doesn't seem very hot


... Bosch Dishwashers

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Why does the metal ring stay hot after cycle is done?


... Maytag MDB7100AWB Dishwasher

Very long cycles,checked the hot water going in and its hot, but still very long cycle..


Hello,\015\012\015\012The first thing which comes to mind is a very common occurance with B/S/H ( Bosch, Thermador, Gaggenau ) manufactured dishwashers, a failed solder on the control board, specifically the heater relay. Since the info you provided ... Bosch 24 in. SHU5305UC Built-in Dishwasher

I have a GE Potscrubber 720 and there is water in the bottom of the dishwasher and I tried to clear it by starting a cycle and it still keeps water in the bottom of the washer. When I run a cycle there is caked on soap on the inside door and dishes and the dishes are filthy. I found a long thin piece of metal by the drain it is long and straight and a break on one end and an "L" shaped bend on the other.. Any ideas where to start looking for problems? As I have no experience in repairing dishwas


... GE 24 in. GSD2600GBB Built-in Dishwasher

Bosch dishwasher SHX46A -cycle runs too long (4 hours)- items still wet. The economy cycle also runs too long - should be about 80 minutes and it ran for 200 minutes.


It sounds like there's a problem with the dishwasher's heating element. The dishwasher uses the heating element to heat the water to certain temperatures, and it will wait (run for extra time) for the water to reach this temperature, and may eventua ... Bosch 24 in. SHX46A05 Stainless Steel Built-in Dishwasher

We have a Bosch SHE45M06UC/50 dishwasher that is acting a bit nutty, first of all the timers are all wrong, mostly too short for what the manual says except the quick cycle and it is too long. There is on some cycles a very long delay before it begins to fill and it seems to alternate between pumping and running randomly


Hi,\015\012\015\012The first thing to note with your make of D/W is the display only shows "estimated time" not actual time. There are just too many variables to give actual times, i.e. water temp. at inlet, drain hose length & diameter, as well as p ... Bosch Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


... Whirlpool Dishwashers

I have a kitchenaid dishwasher model kuds24se with a problem. I MUST hit cancel before I hit start. Note that it doesn't matter how long it's been since the last cycle. It could be a few minutes or a day or more. I have to hit start to get a complete wash cycle. If I don't hit cancel, the washer goes through some sort of cycle and stops. It seems like a normal cycle but of course it is not because I don't hear any water and, upon completion, when I open the door there is heat but the soap dispen


... KitchenAid KUDS24SE Built-in Dishwasher

Hotpoint, intergrated dishwasher BF12/47916/7 has stopped working, There is nothing happening at all. it has done half a cycle the only thing that happens is when you put the cycle on the dot before cycle no: 2 the power light comes on orange, this usually goes red when the cycle is on. I have changed the fuse & there is no difference. Help!


... Hotpoint 23 in. BF41 Built-in Dishwasher

When dishwasher is set to begin, sensor takes very long period of time. Cycles are longer than minutes indicated. Dishwasher fills with water but does not wash. Water then drains as though cycle is complete and moves to next cycle. Then the process continues. When cycle for drying is reached, much heat is given and occasionally it smells as though there is burning. A 82 minute procedure turns into hours.


... Kenmore 24 in. 16532 - Multiple Color Built-in Dishwasher

We have just purchased and installed our dishwasher. Towards the end of the cycles it has a very high pitch noise when the heated drying cycle. Is this normal, or is there something wrong? It is VERY annoying - it reminds us of a 'ringing in the ears' noise. Also - is there a listing of time for each cycle? It seems that it runs a LONG time in each cycle that I have tried - with or without any specific instruction, i.e. heated dry. Thank you.


Hello. This dishwasher is definitely not functioning properly. Call the store where you purchased it and report the problem. Because it is under warranty you have rights. You should return it [this would be my choice] or have the store sen ... Dishwashers

My dishwasher skips the final drain cycle. The lines are all clean and there is no clog. It drains just fine in the beginning of the wash cycle. Every time I do a load of dishes I have to run the full cycle, then leave the machine open for 3-4 hours and start the cycle again and listen for the drain at the beginning of the wash to drain the machine from the initial wash and stop the machine after it is done draining so it won't fill up again. Sometimes we have to unplug it and wait about an hour


... GE Nautilus 24" Built-in Dishwasher

Excessive foaming when using Rinse Only Cycle in Kitchenaid Dishwasher. I've had this dishwasher only 3 weeks. There is no detergent in the dispenser. Rinse Cycle should be only water; no soap. Rinse Aid should not be dispensing either. What could be the problem? Normal wash cycle leaves residue on glassware. That is why I run the Rinse Only Cycle. I have done this over and over with the same results? HELP!!!


Do you have a softner in the house ... GE 15" Laundry Pedestal for Horizontal Axis Washers and Dryers - White-on-White

I have a smeg si 112 eco dishwasher cycle takes too long and last cycle water is not heating


... Smeg Dishwashers

Long cycles My dishwasher (approx 7 years old) will run in the wash cycle for hours...until I physically turn the nob to "rinse"; then it will stay in that cycle until I advance the knob to the final (expel water) stage. I checked the filter and the blades - no obstructions. Also, when completed, the dishes are hot, so I know the heating element is working.


Http://www.thisoldappliance.com/library/bosch_dw_guide.pdf\012\012\012 ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Gaggenau dishwasher model GM326-210/09 with ID No. FD7612 390018. We are not the original owners and it should be around 10 years old. The problem is that it is stuck on the pump out cycle just before the drying cycle and no mater how long the dish washer is left on, it will not stop the pump cycle. Can you help? Brian Stacey


... Gaggenau Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0998 seconds