Having problems with your Dishwashers ?

Telman tel12dwn does not get any water into machine

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Telman tel12dwn does not get any water into machine

... Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a

The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

My Kenmore Elite dishwasher doesn't wash dishes properly. I think that it is not getting enough water in the machine. It only allows about an inch of water to get into machine and then starts. I do not think that there is enough water to spin wash arms. I have 40 PSI coming into the house. I am on well water and found debris in the intake orfice. I did my best to flush. Could it still be bad?

I am having the same problem with my brand new Dishwasher. ... Kenmore Dishwashers

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David

Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

Hi there I have a Miele G663 scvi dishwasher. The inlet/outlet light is flashing. I have cleaned the non return valve and filter at the bottom of the machine. I have also removed the water inlet pipe which has a large filter on at the end where it attaches to the water pipe. I have blown through this pipe and it is quite difficult to get air through. Do you think it is a filter that is blocked? If this is the case are they easy to attach to the bottom or the machine or would I have to get

... Miele 24 in. Incognito G663 SCVi Built-in Dishwasher

I am not getting any water out of the bottom spray arm in my bosch SGS47E02GB35 dishwasher. I have cleaned out the plastic pipe assembly on the left hand side of the machine and the plastic tubes that sit to the right of the pipes. I have blown through many of the other pipes to and dislodged quite a lot of debris which has now been cleared out of the machine. The machine completes its cycle and water comes out of the upper spray arm (there may not be as much water coming out as there should be)

1. Check that water can flow from main pump,though hose to propellor,that there is no blockage. ... Bosch Dishwashers

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".

Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

I have a 11 month old Samsung DMR57 dishwasher that is displaying an E9 Error code (low water level). However there is water in the machine. Does this machince use a thermistor or pressure switch to sense the water level? Where can I get a wiring diagram for this machine?

... Samsung Dishwashers

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?

... Dishwashers

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle

... Bosch 607335 Water Valve Assembly For Dishwasher

I have an zanussi LS6 and in the display it on and off shows the A1 and B2 and spills water. The problem though is not what normally comes with A1 and B2. Somehow the water gets to electrical parts and all power is out in the café. Several experts that has been to see the machine clame it has something to do with the electrical system - that measueres when there is enough water. They say it has something to do with machine having the salt container and they have all given up repairing it. I boug

... Zanussi 24 in. LS6E Free-standing Dishwasher

I have frigidaire dishwasher,starts cycle,can hear water entering dishwasher,checked level of water,does not get to 1",machine starts washing by the sound of motor, but dishes are not clean,water drains machine turns of,cycle complete.what do you think.

Depending on your dishwasher, it fills either by a timer or by a water probe or float. I will assume its a timer as a probe or float wouldnt exhibit this behaviour. I would say you have a restriction in your water supply line. Check your valves, an ... Frigidaire Dishwashers

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?

Hi There,\015\012\015\012Your description seems to indicate a fault in the water heating circuit or components. This is often the reason for a wash cycle not finishing and draining. As the machine will drain when you lift the overflow lev ... Dishwashers

The machine does not seem to rinse properly. We have checked the water fill level, water temperature, spray arms are not clogged, have determined it is not a hard water problem and have tried Glass Magic and CLR to verify the lattter. What else can we check to stop getting a film on everything in the machine? Plastics come out terrible, glasses and dishes foggy and sometimes still greasy. The model # is GU2700XTSY0 from the Whirlpool line of Quiet Partner 4. Any suggestions would help. Thanks!

Too much detergent; not rinsing well; hard water... There is an acid wash to revamp glasses/ you'd need to google it... ... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher

I have an Electrolux dishwasher model ESF489, and I can't get water to go into it.the water goes as far as the machine then the inlet hose just pressurises up.I know the hose is clear .The machine tries to go through its cycles but because the water will not flow,it just cuts out after a few seconds.????

Assuming the control card is working ok, the most likely problem is the water inlet valve which may have a faulty solenoid. Do you not get any indication of beep or fault lights on the dishwasher.\015\012You can find a possible replacement at ... Electrolux Dishwashers

Hi, I get a problem reading " E4". I have now switched the machine off and on again, but still it says the same. Incidentally the machine has already pumped the water out, so the 'overfill" is actually not supposed to be a problem. It is KELVINATOR EXTREME CLEAN DISHWASHER, model KD14SS. Please help, how am I to get rid of this problem, I really do not have the time nor the money to get outside help! Anita Kleynhans

... Kelvinator MDP531RF Dishwasher

My Frigidaire FDB935RHS0 top rack is not getting enough water (pressure) to rotate the top rack sprayer. We have looked at all the connections under the machine as well as the tubing, but we have not found any obstructions or problems. The water moves very slowly up the tube to the top of the machine and the water only seems to trickle out of the feed line therefore the sprayer doesn't spin or spray. We have disassembled the bottom sprayer and have found no obstructions there either. Do you have

... Frigidaire 24 in. GLD2350RC Energy Star® Built-in Dishwasher

I have a Hotpoint Aquarius FDW 20 dishwasher. Prewash and Wash lights were flashing, machine had stopped and water was at the bottom of the machine. What does this indicate? After removing some debris from the water drainage pump, then reassembling the machine, I now get the pre-wash LED flashing and a motor operating, but no futher progress into the wash cycle. What does this mean?

Dishwasher always full of water at the end of cycle ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Machine just started leaving dirty water in bottom of machine. cleaned filters,had machine apart,removed and cleaned waste pipe. pump runs and impeller feels ok.only time i could get any water to drain into bucket was when shook waste pipe very hard?

Check that the pump is clean and not loose. Make sure pump, impeller, and waste pipe are in alignment with each other and are clean. If it works when you shake the pipe, then there is still a clog inside or the pipes aren't aligned correctly and some ... Dishwashers

Bosch SHX45P05UC-64 dishwasher hums with no water. I checked the water inlet line & it is getting water to machine(no kinks)

... Dishwashers

The water is not coming into the machine and the tablet is still dry even though it comes out the draw, the dishwasher makes a noise but no water s getting into the machine

Check your water inlet hose and any filters attached to it. Some hoses have a little turnkey tab to turn them off. Make sure this has not accidently gone into the shut off position. If you pull out the machine you will hear if the water is coming in ... Dishwashers

I have a JDB1090AWS about 3 years old. We noticed a smell and found cutting boards and plastic cups melted. Machine was off. Had to turn off the breaker. Checked both leads to element & have power even with machine off. Not sure if it could be the limiting thermostat; I assume that is to shut the heat down when it gets too hot. Element is on though when it shouldn't be to begin with. I did have to tighten the water supply. Had some water underneath, but all wires seemed dry. Any tests I should t

The heat element can only get so hot.It's timed so it doesn't exceed a period of on, exposing dishwasher contents to continuous high temps.Watch the timer and take note how long it broils your cookware.Good luck. ... Dishwashers

The dishes have food residue washed onto them and water spots on all glasses regardless of the amount of detergentinse agent. The pump seems fine there is no water left in the machine after a cycle. any suggestions other than getting a new machine? thank you!

Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... Bosch 24 in. SHU43 Built-in Dishwasher

Where can I get the instruction manual for a Bosch Classixx Dishwasher SGS53C12UK? I have bought a second hand dishwasher that has only been used for 6 months. The programme works fine but when I go to use it again - check water shows on the display. I have to tilt the machine back as water is stored at the base of the machine, surely this is not normal? It there a simple solution to this or alot of cost involved with a new part? Any help would be much appreciated. Thank you.

... Bosch Dishwashers

Last couple of days bottom rack of dishwasher not been clean on 65o wash, having emptied and run the machine empty etc it seems that whilst there is water being pumped through the roof mounted vents and to the "spinner" attached to the upper tray, the spinner attached to the base of the machine is not getting a) any / b) sufficent water pressure to make it spin...im guessing the feed is blocked?

... Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1459 seconds