Having problems with your Dishwashers ?

Bullfrog 552SS pump and heater issues

\015 I was wondering if I could get some help. I recently bought a used Bullfrog 552 and had it installed 3 days ago. Specs are:\015\012\015\012Base Unit 552SS\015\012Control Pad Premier 8-button Control Pad\015\0122 Pumps, 2.5hp\015\012\015\012A couple of things have occurred that concern me:\015\012\015\012First, after it went through the priming setup, I set the temperature for 102 degrees. The water temp was at about 71 degrees. After three full days of heating, it's only now reached 88 degrees. Is it normal for the temp to take that long and only be halfway to its programmed stop?\015\012\015\012Secondly, we got in for a few minutes last night. Jet 1 is always on low, because that's the filter/heater jet. We turned Jet 1 on high and Jet 2 to high. Everything worked great for about 10 minutes and then, all of a sudden, Jet 1 shut completely off. Jet 2 was still running. Shut off Jet 2 and looked at the control pad. According to it, Jet 1 was still running, yet nothing was coming out. I could hit the Jet 1 on the control pad and hear a click as I moved from low to high and back to low, but nothing happened in the water. Jet 2 still worked just fine, though. I reset the breaker and Jet 1 still wouldn't turn on. Left breaker off for 20 mins, turned it back on, Jet 1 worked just fine. Left it alone for 24 hours, ran continuously the whole time with no problem. Just tried turning on both jets again and same thing happened. Jet 1 stopped running after about 10 minutes. Shut if off for 20 mins and it went back to normal.\015\012\015\012There are no warnings or anything on the control pad. It actually thinks the jet 1 is working perfectly well. It shows the symbol of the moving jet on low.\015\012\015\012Any help would be appreciated. \015\012\015\012Jim\015

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bullfrog 552SS pump and heater issues


... Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

E3 Error Hi My dishwasher is showing error E3, which the user manual states "The appliance is not able to pump out the water.", however, other E3 error states a heating issue. The dishwasher does in fact heat the water but generates the E3 error after 10 minutes or so, then pumps out the water from the dishwasher. I'm a little confused as to what the issue is here and what part I would need to rectify the problem. Any advise you could give would be greatly appreciated. Kind regards


The E3 error is a result of water temperature not getting to a nominal value within a particular time. This could be caused by several factors like heater faulty, wash pump not working well, wash arms not circulating water as required. Need model nu ... Smeg Dishwashers

We recently purchased a new pump for our frigidaire gld4355rf dishwasher. The old one started making grinding noises. When we moved the dishwasher it had leaked due to a failure of an interior seal. Our new pump is now making the same grinding noise but it is not constant. When my husband adjusted the pump by using his hand when he got into a certain position the noise stops. We keep the screens clean. Is there an issue with the pump in this model?


... Frigidaire GLD4355RF Dishwasher

Not cleaning on top rack. Pump, fill tube asm. & spray clean. Has any seen if this issue could be the deverter motor in the pump or the control board?


Just to review, the LG dishwasher family, including the LDS5811 has the Verio motor and the check valve that diverts water from the bottom rack to the top rack. If the valve is blocked/jammed, this would cause the symptom you describe. T ... LG 24 in. LDS 5811 Built-in Dishwasher

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Kitchen Aid Dishwasher KUDR24SEBLO does not drain 100%. I have removed the drain hose and chcked the sink P-Trap, [it drains thru the garbage disposer]. Unit is 10 years old, otherwise works fine. I am having difficulty removing the impeller and items above the pump to see if it is clogged. Do you think I have a partially clogged pump or a timer issue that prevents the pump from completely emptying the bottom of the dishwasher? We have run the dishwasher 20-30 times since observing the problem.


Hi there,\012Please check out the following -Pump - Your dishwasher pump ejects the water. The pump is usually mounted directly to the motor, then attached to the bottom of the dishwasher. You can reach the pu ... KitchenAid Dishwashers

Noticed water on floor. Found both heater nuts cracked and letting water by the rubber gasket and tub. Water leaking into the heater power supply wires. Bought new nuts and want to know if this is a constant issue. Nuts are just cheap stampings and it seems likely it will happen again. Any suggestions Don


Change out your heating element as well. Sounds like you need a better seal. \012\012Thanks ... Dishwashers

Pump Issue I have a john deere pressure washer. I hook the hose up to it, rurn the water on and no water comes out of the wand. I started the engine briefly and pulled the trigger on the wand and still nothing. The model number of the pump is Annovi Reverberi SJV 2.5G24-1. I can't seem to find any info on the G24? There is info on the G27-1. Not sure what to do here? Please help.


... Pressure Washers

Our kitchen drain clogged recently and water drained back into our VUD141 dishwasher. A plumber cleared the drain, and turned on the DW - which pumped out the standing water. But now, we have no water flowing into the dishwasher. The drain pumps, the heater works, but there's no water supply. The plumber who cleared the drain said he didn't DO dishwashers, and I cannot locate the owner's manual since we prepared for a move.


Hi\015\012\015\012 \015\012\015\012When the dishwasher won't fill and the water supply is on,\015\012then the issue is with the water inlet valve which is either clogged or\015\012blocked, you can try to clean it. If this wont so ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

So I found this power washer for sale. The seller claims that the washer generates a good stream of water, not just full power. He also mentions that after a few minutes the engine starts to bog down like it is working extra hard. Does this sound like a pump issue? Could something be clogged or would the pump need to be replaced? Or should I avoid this power washer?


Don't buy a power that doesn't work.There are many expensive parts on a power washer. If it was cheap and simple to fix, the seller would fix it and the washer would not be for sale.Would you buy a car that doesn't work? Especially ... Pressure Washers

I have a bosch she44c05uc dishwasher that get stuck on 1 and won't finish. The water will pump out when I cancel. The water will pump in but won't heat up. The final heating doesn't seem to work also. I have removed the circuit board and there appears to be NO solder issues. What else can it be?


... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher

I have two DeVilbiss issues: First, on my pressure washer, I no longer get pressure on "high" mode from the hose. I prime the pump but it doesn't seem to be creating enough force for a high pressure. Second, on my generator, the gas from the gas tank leaks out. The tank is plastic or poly and don't know if it's a gasket issue.


... DeVilbiss Pressure Washer Hose 3600 Psi 25'

My troy bilt pressure washer only runs a few seconds then dies.I thought the pump was plugged so I removed pump.While pump was off I ran the engine in case it was a fuel issue,The engine ran fine.Whic


... Pressure Washers

We have and older Jackson model 10 AB at church, used 10 to 20 times per year. The pump motor quit this summer and was replaced by a local appliance service company. About $700 job. Upon using it recently, the first time since the new pump was installed, the RINSE cycle seems very anemic, that is, low volume and low spin rate. The dishes were not completely rinsed. Temperature was correct, 185 degrees. The service person came back to look with no improvement and now the Heaters will not co


Sounds like a wiring problem but it is controled by a thermo to make sure you get to the proper tempt . so ck the connections and mke sure the thermo is good . . and the element is good . ..hope this helps mm . ... Jackson 10A Free-standing Dishwasher

Kitchenaid dishwasher model KUDM01TJB0 Fills with water, heats water but pump dosent run in wash (dosent spray water) Drains water. Every thin appears to work but the pump in the wash mode. I checked the control board and it has no visable issue.


... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Dishwashers

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Turns on, the entire cycle runs, but no water pumps through the sprayer. There is water present on the bottom....and I can here the water pumping in at the beginning of the cyle....but the dishes are not being 'washed' by the sprayers. I have disassembled and cleaned the entire inside and sprayers to no avail. Im thinking its a pump/motor issue but Im not sure because the sprayers spin, the heat comes on, the detergent dispenses....but no water is being sprayed. Thanks.


Yes i agree, your pump is not working as it should. J.\015\012\015\012That said if this machine is over 3 years old, replace it. The new ones are so much quieter, better, and cheaper to operate. J. ... Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Magic Chef DU55CA-01 unit runs but when pump kicks on for discharge cyle water leaks on the floor from the what appears to be the solenoid part. The leaking stops as soon as the pump turns off. What part needs to be replaced? The unit was in storage for some time would this just be an issue with it sitting for some time? What is the best way to determine the real cause of the leak?


Leaking from drain valve shaft seal. If you just replace the seal it may still leak. Replacing the pump is a lot of work and not really worth it to cure a small leak. ... Magic Chef 24 in. DU6550 Built-in Dishwasher

I have an AEG OKO 4040 Favorit which will not perform the main wash cycle. Water fills ok & pumps out ok. Heater element is working fine. any Idas


... Dishwashers

Asko dishwasher won't fill or pump, panel lights and heater on?


First, check the usual suspects: Make sure the circuit breaker isn’t tripped and that the wires at dishwasher’s power ju ... Asko 24 in. D3250 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0809 seconds