Having problems with your Dishwashers ?

I have a Whirlpool ADG7966 which started malfunctioning yesterday: the delayed start option locked the washer and does not change or allow it to start the cycle. I already turned the machine off/on and also tried doing it from the home power "switchboard". Any help reseting this is most welcome! Thanks for your attention - Nuno.


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Whirlpool ADG7966 which started malfunctioning yesterday: the delayed start option locked the washer and does not change or allow it to start the cycle. I already turned the machine off/on and also tried doing it from the home power "switchboard". Any help reseting this is most welcome! Thanks for your attention - Nuno.


... Dishwashers

I have a Husky 2600 PSI power washer with the Honda GCV160 engine that I can't get to start. It was okay when I purchased it from Home Depot last spring but now I've tried putting new gas in it, spraying carb cleaner, new spark plug, and it still won't start. I only ran it for about 30 minutes when I first purchased it. The guy at the service desk at Home Depot told me that the water hose should be attached and turned on while trying to start. Is this true or would this be starting the motor und


You can eliminate the motor by unbolting the pump from it and then if it will start the problem is with the pump or the unloading valve.If it does not start with the pump removed then you check for spark and get the carb cleaned or have a kit put in ... Karcher 2500 PSI Pressure Washer

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

Have MDB7609AWW2, and tonight tried to start machine and nothing would start. No lights, no activity. We took a look inside and tried to straighten out the top arm cause it wasn't turning freely. Also checked the circuit breakers. Please advise.


... Maytag MDB7609AW Builtin Dishwasher

Kitchenaid dishwasher KUDS35FX starts then resets, started after recent power outage. Tried unplugging and resetting but did not help. Also tried all cycles but same result?


... KitchenAid Kitchen Aid KUDS35FX Dishwasher

My dishwasher (kleenmaid brandt super silent DW121TB) appears stuck in a wash cycle; how do I reset the program? I have read the instruction book to no available, tried unplugging power overnight, tried a combination of simultaneously holding buttons in and switching on, letting the machine run all night, drained the water and added clean unsudded water, and none have corrected the situation. There is also a selection lever inside the machine that is not identified in the instructions, it appea


When you say it is stuck in a wash cycle, do you mean the wash arms are continuously running?\015\012Is there water in the base when you open the door?\015\012\015\012Can you try to run the dishwasher in any other program like rinse ... Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

Have a KUDS24SEAL5 superba and no lights come on after pressing any of the buttons. Power to machine is good. Several months ago it would not start properly by pressing 'start'. Would go directly to 'drain' cycle. Then found that if we pressed 'rinse' before 'start' it worked fine. Now, almost a year later...no lights, no one home...any thoughts?


I had a KUDP02CRB and there is a hidden transition connector on the front panel under a black plastic cover that was pulled out a little. It connects the flex cable from the controller board to flex circuit of the panel. I just pushed it back in al ... KitchenAid Dishwashers

My Asko D1996 Dishwasher will not start. The control panel has 3 lights staying on - position #1, 6 and 7 and are unresponsive no matter what buttons are pushed - even after turning the power off at the breaker, the outlet and the on/off button.I've tried holding down the start button for several seconds to reset but this did not work. I have also cleared the drain, filters and removed any water and pushed and held the Start button to reset.


... Asko Dishwashers

I have a whirlpool DWH B10W. Last week the main drain outside blocked and none of my service machines were working (not draining). The main drain has now been unblocked and every machine except the dishwasher are now working fine. The plumber has checked the drainpipes again and says all are now clear. When I try to use the dishwasher, after the initial drain it stops and starts beeping at me. I have also noticed that no water is going into the machine. What's happening?


The error most likely indicates a Long Drain Sequence (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. \015\012 \015\012 \015 ... Dishwashers

Hi, I have had a few issues with my ST663 machine. The current problem: the rinse cycle light keeps flashing and it doesn't start when you shut the door. I have tried holding down the right button but it beeps twice and nothing happens? Also tried holding both buttons down for a while and still no success. I got a new electrical board installed not that long ago so not very happy hoping it not a big issue. Do you have any other things that I could maybe do?


HiIf you have already tried to reset the unit by pressing the High Temp wash-heated dry button for 3-4 times in sequence then the problem is either with the door switch or the keypad itself that has gone bad and should be replaced. Hope t ... Dishwashers

Hi, I have the Bosch Logixx Dishwasher . BOSCH SGS0922gb /06 .. aged about 6 years old .... When I press the on/off button 'on' the led display only shows the 'not started' message. When I press the on/off button 'off' the led display lights up momentarily with 'start' etc just before I have fully released the button. I have tried a new switch and the same happens so not that. ALSO i can sometimes see S1....> on the top panel and get the machine to show on the top panel the close door


... Dishwashers

I have a Siemens Dishwasher. I'm not sure of the model but it is built in, has concealed controls and was purchased about 6 years ago at Best Buy. It sort of looks like the SL85. When started, it runs for a few minutes and then starts to make a horrible sound. ALmost a grinding sound but may also be like water trying to get through a small opening. The sound does not stop even after turning off the DW and even the power to it. Only turning off the water supply does it stop. Help?


... Siemens SL85A705UC 24 in. Built-in Dishwasher

I have a older simpson 3000 power washer, 11 hp honda,been a great machine, owned since new, seems like the pressure is building up to a point where it has blown 2 hoses, i turned the throttle down and started to wash, engine quit after about 15 min. it restarted and quit again, tried starting fluid , nothing, what might be the issue


... Honda Pressure Washer PSI 3000

I have kenmore 16438 built-in dishwasher and red light is keep flasing on smart wash button. If I try to press to cancel button then normal wash button is flasing on red light along with cancel button. Also, I won't start. I try to turn off the power, still not working. Thank you.


... Kenmore 16483 Built-in Dishwasher

Starts cycle, drains ok, then "intake/drain" LED comes on solid for 4 seconds, flashes 4 times, solid 4 seconds, flashes, etc. no water coming into dishwasher. DOUBLE CHECKED the intake filter its all OK ! how do i 'reset' the machine? Im pretty sure the sensor is goofed up and needs to be reset but i have tried holding various buttons, start, power etc, cannot figure out how to do it


... Miele G2430SC Dishwasher

Can't start the dishwasher, lock button is lit up. Tried to hold down many buttons for 3-5 seconds, but lock button continues to stay lit up. Tried resetting the power to machine, but nothing changed. Please help.


Hello Albert, On the Jenn-Air dishwasher you have, you have to hold down the "Heated Dry" button for 3-5 seconds to unlock the control panel.\015\012\015\012This should unlock the controls so you can again use the dishwasher normally. ... Jenn-Air 24 in. JDB1090AWS Stainless Steel Built-in Dishwasher

Jackson jp-24b purchased this machine used, cant figure out how to work it. I flip the auto cycle on, and then the power switch. The fill light turns green and i assume water is filling up in the machine. In the meantime there are two small red external hoses that hot water comes and i currently just have those hanging in the sink. At the same time, nothing is happening during the wash cycle, the wash gauge doesnt even move only the rinse gauge. Also when i try to drain it nothing happends (begi


It needs a new drain relay box 120 volt the drain is stuck open the jp 24 were not very good machines the red lines are drain lines if you plug up the drian lines at fillup the machine will wash but now it will never drain a new drain box is not c ... Jackson JP-24B Built-in Dishwasher

Try to install LG dishwasher LD-1403W1. after power on and start program, Machine was not working with error IE ( water is not supplied). Checked and found water tape was opened but somehow water was not able to bump in to the machine.


... LG Dishwashers

My power was out in my home briefly while my hotpoint bfv620 dishwasher was running. Once the power returned the washer's indicator lights 2 & 4 were flashing. I've tried reseting the machine, turning it off and back on and the lights remain flashing. Any thoughts?


Turn it off and give it more time than before then put it back if the flashing continues then remove the water out of the hose and check that the hose isnt blocked, check the pump if blocked , then it continues that means may be the suppply surge m ... Hotpoint Dishwashers

My beko DWD8650 dishwasher has stopped working - when I switch on the power, the machine sounds as though it is trying to work, even though the start button has not been pressed. Once the start button is pressed, the timer does not count down and nothing else happens.


... Dishwashers

Whirlpool ADP 4501 problem. Starts normally andthen after 30 secondes or so begins to 'pulse' ie pump runs briefly then stops and the power 'start' light flashes with each pulsation. No water coming into machine, seems to be trying to pump out but stopping


Sounds like electronic module failure if there is no water in machine. ... Whirlpool Dishwashers

No Power Hi. My dishwasher wont start. I loaded it and cannot get any lights to light up on it. There is no power to it at all it seems. I tried flipping the breaker but there is still nothing. The door locks, so that shouldnt be the issue. Is there a way to reset the machine? What should I do?


I have the exact same problem with my Kenmore Type 575-0. It was working one daym it went into dry storage for a year and then when I took it out of storage it would not work. Ive already tested the thermal fuse and there is nothing wrong with that. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1550 seconds