Having problems with your Dishwashers ?

Dishwasher Kenmore E4 flashes in screen, well only drain salt and additive lights are on


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher Kenmore E4 flashes in screen, well only drain salt and additive lights are on


... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

We have a Kenmore Ultra Wash Dishwasher Model number 665-13859K601. The Normal wash and the Cancel (drain) buttons are flashing red on the control panel. No matter what we have tried, we have been unable to correct this problem. Obviously the dishwasher does not function. When you close the door the lights keep flashing and no button combinations seem to do anything. I have looked at the troubleshooting guide that came with the dishwasher, however there is no


... Dishwashers

We have a kenmore elite dishwasher model number 665.13249k900. The normal wash green light is flashing but none of the buttons will work . If I press the cancel drain button it will come on too but it will not do anything. I turned a power off for a short w hile but the light continues to flash


... Kenmore Dishwashers

Kenmore Dishwasher My dishwasher fills with water and then stops. I hear the cycle timer continue all the way through the cycle. I pulled the screen off the bottom inside of the dishwaher and stuck my hand in the diswasher drain. Originally I felt and cleared what appeared to be a torn up rubber band. I feel a thin straight metal pin that I can rotate and I believe it causes the pump to rotate as well. Once I do that the dishwasher will run normally thorough a complete cycle...BUT I have to


If you have either dry bearings in the motor or sticky grease buildup in the pump bearing/seal, it can cause the motor to stick rather than rotate on startup. More likely to be greasy crud buildup. \015\012\015\012The best you can do without disasse ... Kenmore 24 in. 15149 Built-in Dishwasher

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

I have a Miele G892 SC dishwasher. When I start the cycle, it drains (except for a bit of water left below the triple filter). After that, the intake valve opens and water enters. It then does nothing for a period of time until the "intake/drain" indicator light starts flashing. When I open the unit, I find about 1/2in of water in the tub (above the tripe filter). I have 1. cleaned the intake valve filter (no blockage found) 2. Inspected the drain line at the base of the unit as well as t


The pump is running due to the float switch or the float itself either being stuck open or broken and showing a fault this is why you have water going in to a certain point but not the point required for washing the dishes and then due to the float s ... Miele Dishwashers

Kenmore Elite 665.7696 dishwasher - "normal wash", "pots pans" and "cancel drain" lights flash on control panel. If power shut off for some time will work for part of load then start flashing again and stop. Is this a trouble code? If so, what does it mean?


Hi\015\012\015\012This error code appears when either the keypad(Part#1 in below link) or Control board(part#11 in below link) is faulty. You can reset the error codes sometimes by turning Off/On the power, however, this is not a permanen ... Kenmore Dishwashers

I have a kenmore dishwasher model #655.1374 or 655.1384 which is only about a year old. I am having a problem with the controls. It will not allow me to use smartwash. The only control that can be used is quick rinse. I reset it by pushing Sani rinse and heated dry. All the lights come on and it seems to do a test. But after that still the same thing except if I push start resume it goes to normal wash which stays on a long time and periodically the cancel drain light comes on as well as the 4


... Dishwashers

Troubleshooting Miele 18 in. G611SC Plus Slim-Line Free-Standing Dishwasher, Support & Service: Salt PC Light is red and constantly on and the inlet and drain light is flashing red.


... Miele 18 in. G611SC Plus Slim-Line Free-Standing Dishwasher

My dishwasher will not start just these three lights are flashing at the same time. What should I do? The three lights that are flashing are smart wash , normal wash and cancel drain. The dish washer


Try turning breaker panel for that off, and back on. might just need to be reset. If that doesn't work, call the repair man ... Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

It won't complete a full wash cycle keeps stopping part way through and low rinse aid, low salt lights flashing even though both are full ??? Pamphlet says this might also mean there is a kink in the inlet hose but that seems fine as well. Have had the dishwasher 3 weeks and it has completed about 4 cycles without stopping ???


Check water valve to see if it has something blocking water supply ... Dishwashers

Below the filter the dishwasher is sitting in water and will not drain. When the programme goes on, it will go off and the quick programme inidcator light will flash. I have switched it off and on I have checked the hoses for blockages as well as the sink Help please!


Do you have a garbage disposal? There is a vent in the tube that runs to the sink that can get blocked. There is also a screen or filter in the bottom of the machine that can get clogged. The pump can get jammed with debris as well. ... Zanussi 18 in. ZDT5052 Slim-Line Built-in Dishwasher

Dear sirs, I own a Kenmore dishwasher Model # 665.17039400. The clean light flashes 7 times and then repeats. It will not run, only the drain button will work. I changed the heating element from advise on another forum. This did not resolve the issue. Please advise promptly as my wife is going crazy without this appliance. Regards, R. Carmikel


... Kenmore Dishwashers

Whirlpool dishwasher gu3600 The pots & pan, normal light and delay lights flash all the time. Also the time remaining screen has two horizontal lights on. The dishwasher won't start


... Whirlpool Dishwashers

KENMORE ELITE DISHWASHER - MULTI-LIGHTS FLASHING


Look at your manual, usually available on net for reading or downloading. Blink lights are often used to code out a problem with various combinations and repetition rates to indicate trouble code number for look-up in manual. ... Kenmore Dishwashers

Kenmore dishwasher, model 665.170 344 01. "Clean" light keeps flashing and will not stop. Have tried everything in the manual and the light still will not stop flashing.


Only reset you can do is unplugging power cord for 10 minutes.The control panel it is probably faulty and in need for replacement. ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Kenmore dishwasher Clean light flashes after reset goes through cycle but motor does not run then clean light comes on again.


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Bosch dishwasher I have a month old Bosch dishwasher. It was stopped mid cycle. I drained the water at the bottom, but the active light keeps flashing, and when I press the start,reset button, then turn it off, it does the same thing when I turn it back on. active light keeps flashing and the wash light is on. It won't even lock the door. How do I fix this because there is no Bosch dealers here to help with the problem.


... Hotpoint 23 in. BF41 Built-in Dishwasher

I have a Kenmore Elite Ultra Dishwasher and the cleaning light is flashing. I have tried pressing the start/resume button and closing the door within 3 seconds. I am not able to turn on my dishwasher. I have tried turning off the power for 20 minutes but when power was restored the green light continues to flash and the dishwasher will not work. This machine was installed in May 2008. Help!


If the clean light flashes 7 times, pauses, then repeats...When\015\012the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non ... Dishwashers

My Hoover dishwasher HFI 3015 is not working. When you turn it on, the P1 and 'out of salt' light is flashing and bleeping constantly. I believe that it may have run out of salt yesterday, but I have filled it this morning and there is plenty of Dishwasher salt in the compartment now and it is overflowing with water. I have tried turning the machine on and off, but each time I turn it on I get this bleeping and flashing and can't stop it. Any ideas?


... Hoover Dishwashers

I have a KitchenAid dishwasher, model KUDP02FR. The "normal" cycle light is flashing. When I push "cancel" or "resume/start", they start flashing as well, but the dishwasher won't start. I turned off the power and turned it back on. The "normal" light still flashes, but when I press "resume" it all starts over again. Any ideas? I can't find this in the troubleshooting guide I have. Thanks.


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid KUDI01TBK Dishwasher

Jenn-Air 24 in. JDB1080AWS built-in dishwasher green lights flash on and off on their own sometimes - not able to start dishwasher sometimes - not able to use settings (lights don't light when pushing top setting buttons - dishwasher seems hot about 8 - 12 hours after use = cleans very well though - dishwasher wasn't used much from 2005-2007


... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2505 seconds