Having problems with your Dishwashers ?

I have a dishlex global 300 and I had to take the door lining off a few questions first where does the r8 wire connect to and when I turn it on the eco rinse and super lights are on and the machine does not work aqny ideas


Answers :

This can happen due to multiple reasons:\015\012check the following:\015\012Check If�
Heater circuit problem:
♦ Open heater.
♦ Wire disconnected, open connection or component in heater circuit.
♦ Faulty heater drive circuit on control


then to solve :Then�
1. Check operation of heater in Diagnostics cycle.
2. Unplug dishwasher or disconnect power.
3. Check resistance of heater and all components and connections in the water heating circuit or heat dry circuit.

or

Door switch not making contact consistently:
♦ Misaligned door latch assembly (which can be aggravated by high door closure force keeping strike plate from fully seating).
♦ Faulty door switch (high resistance).
♦ Loose or missing installation anchor screws, causing tank to shift in cut-out.


then try this:
 Measure resistance of door switch contacts while checking mechanical operation of latch assembly. Confirm switches not loose from assembly. Check strike plate and door closure.



Hi there,

I have tried to research your dishwasher to see if I couldn't find a wiring schematic, but I haven't had any luck. I was able to obtain a number for Electrolux's customer service dept. that you can call to find a service center in your area, or possibly to even see if they would supply you with the wiring diagram that you need. However, while researching your dishwasher, I stumbled across an article that some might find a bit disturbing if they own one of these dishwasher's. I have included the actual article below. I hope that I've been able to point you in the right direction and that this info proves to be useful. Have a great evening!

James

Article:

Sale of fire-risk dishwashers banned5:00AM Thursday July 24, 2008
New South Wales last nightbanned the sale of dishwasher brands fromAustralia's largest whitegoodssupplier after the faulty machines werelinked to a string of home fires.
Morethan 26,000 Electrolux,Electrolux Dishlex and Westinghouse dishwasherssold in Australia andNew Zealand since April last year have a potentialwiring fault.
TheNSW Fair Trading Minister, Linda Burney, said herdepartment had beenalerted to 73 incidents involving the appliances,resulting inexcessive heat and kitchen fires.
Electrolux identified a fault with the dishwashers last year and has issued three appeals to consumers.
"Despitethis,Fair Trading has received reports that fires or incidentscontinue tooccur," Ms Burney said. Up to 5000 of the dishwashersremain inhouseholds unchecked.
The minister said a wire connector within the appliances could cause plastic components to melt in the control panel.
The largest number of faulty washers are in NSW.
The state Commissioner of Fair Trading has moved to ban NSW retailers from selling their remaining stock of the appliances.
"The prohibition will ensure that any dishwashers not alreadyquarantined by Electrolux, which may be in retail outlets and not inthe possession of Electrolux, are not sold," Ms Burney said.
Thebanand the recalls cover Electrolux, Electrolux Dishlex andWestinghousewashers with serial numbers ranging from 70700000 to72400000.
TheNSW Government said consumers with one of thesemodels should stop usingthe machines immediately and contactElectrolux to arrange for atechnician to fix the problem.
- AAP

This story was found at: http://www.nzherald.co.nz/section/1/story.cfm?c_id=1&objectid=10523214

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a dishlex global 300 and I had to take the door lining off a few questions first where does the r8 wire connect to and when I turn it on the eco rinse and super lights are on and the machine does not work aqny ideas


This can happen due to multiple reasons:\015\012check the following:\015\012Check If�Heater circuit problem:♦ Open heater.♦ Wire disconnected, open connection or component in heater c ... Dishwashers

On the top drawer of the dishwasher the control lights - Heavy, Normal and Eco are all lit up and on the display at the front it says 05 mins the machine keeps going in to a diagnostic rinse cycle and I can not get it to stop, any ideas


Unplug the machine and try again. Sometimes resetting the board can solve the problems, other times it's just a faulty board.\012\012Good luck ... Fisher DD603FCSS Dishwasher

Frigidaire dishwasher can't get to work I have a little "lock" light on rinse hold that says 3 seconds and I can't get my machine to turn on? Any idea...


When my wife got home, she told me where she put the manual. After reading it, all you have to do is press the rinse button for 3 seconds and the lock light will go off. I am not going to take off any electrical panel. ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Kitchen Aid Dishwasher - model: KUDPO2CRBLOrn Ran the dishwasher twice on pots/pans cycle and sani rinse with a special cleaner recommended due to build up and items not getting clean. (soap left all over them) Cleaned machine out great! Now, the only choices that will light are "quick clean up" and "rinse only." Even if I choose them, when I hit the "start" button - the machine will not start. No other lights will light. Machine will not start. Any ideas?? Thank you!!!


... KitchenAid Dishwashers

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

FDW60 dishwasher - taken apart pump and that is clear. Seems that dishwasher fills, and empties and heats all OK but water wont go around the machine ie the motor pump doesnt start - any idea how to take this out and replace without having engineer around? Taken small pump apart and its clear. First of all the Eco and fast light flashed, then we took it apart with some direction from online discussion advice. Now Eco and Pre wash lights are flashing. Machine empties water, then fills with


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

Myy kitchenaid dishwasher model kudi01flss doesn't start even though the lights on the panel light up so I opened up the door to look at the latch and found a broken plastic piece that appears to be part of the latch. Could this be why the machine doesn't start. The funny this is the door still seems to snap closed even with this broken piece but what I'm thinking is that this piece activates some sort of electrical connection that turns the machine on when the door is closed. Any thoughts on th


... KitchenAid KUDC25CH Dishwasher

Hi, I have a fisher and Paykel double dish drawer model DD605. A couple of days ago when we opened the top drawer all the lights flashed and beeped in sequence repeatedly and would only stop when the power was turned off or the dishdrawer closed. Today I went to turn the top dish drawer on and cannot change the cycle off rinse. I can push the eco button and the rinse cycle works no problem but I cannot change the cycle. The bottom drawer is running as I write this and appears to be fine. An


Hi\015\012\015\012\015\012Could you please let me know which all lights are blinking/lit solid in sequence from right to left. This could be an issue of drawer lock mechanism or flood switch issue. PLease post back with detai ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

I have pldb998ac frigidaire dishwasher. The rinse light stays on, and it won't start. Last night it was pretty loud while running the dishwasher, smelled a bit like plastic, and today only the rinse light. The heating element seems to turn on as well when the door is closed. Help - any ideas?


... Frigidaire PLDB998A Built-in Dishwasher

My Hoover dishwasher HFI 3015 is not working. When you turn it on, the P1 and 'out of salt' light is flashing and bleeping constantly. I believe that it may have run out of salt yesterday, but I have filled it this morning and there is plenty of Dishwasher salt in the compartment now and it is overflowing with water. I have tried turning the machine on and off, but each time I turn it on I get this bleeping and flashing and can't stop it. Any ideas?


... Hoover Dishwashers

My ASKO D1996 Dishwasher will not turn on, checked the power and it is running, but no lights or anything turns on. I don't have the water connected to the machine, could this be the problem?


NO, you should get light actions even if the water was not connected. this is a main control issue. there is a control board kit available for your unit. you will need to replace this damaged control in this case. the logic sector is damaged. ... Dishwashers

Hotpoint LFT114 power light, rinse and eco lights are flashing and wont turn off or on


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Machine Won't Start! I have a KA dishwasher KUDPO2CRBLO and only the "quick clean up" and "rinse only" buttons will light up. Even when they are lit, I hit the "start" button and it will not start. The other cycles won't light at all. Any ideas?


Link for all appliance model numbers.\012Please post your entire model number.\012After you have clicked on the link below....\012Just to the right of the "search" tab click on "help m ... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

I have a kleenmaid Dw29x got it as a gift from my brother in law, its all hooked up ready to go but when I turn it on all i get is the pump draining the machine and the exclamation light on the front of the machine is flashing like mad any ideas?


... Dishwashers

Won't work When i turn the machine on the on/off button lights up but the program lights don't, any ideas??


I hant not seen this unit but what it sounds like to me is the control bord that controls the functions on the washer may be bad. you should try and find if there is a tech sheet somewhere in the cabinet or under the dishwasher. that will help you to ... Zanussi 24 in. DE6744 Free-Standing Dishwasher

Same cda cw447 dishwasher machine, first 4 programme lights flashing and beeping noise as soon as machine turned on. any ideas ? thanx


... Bosch Dishwashers

Dishwasher does not wash simply beeps continously and wont start the rinse cycle with green flashing pre rinse light. Have tried turning off at power and have checked all connecting pipes. Have emptied dishawasher also all to no avail.


If your dishwasher is a whirlpool or IKEA then maybe the answer given by emmanuelr in "Whirlpool dishwasher ADP5962 F7 error code" may do the trick. It certainly worked for me. Bit technical but if you are happy taking the sidepanels off the thing th ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Had new kitchen so just re connected my dishwasher. Warning light to check water has come on. hoses and water going into machine seems ok but machine seems to be slow at filling. looked at filters in case of blockage with no result. Any ideas would be helpful please Merry Christmas Janice


I would remove the water line going to the dishwasher and let it run into a bucket. Sometimes on older shut off valves when you shut them off and try to turn them back on they get gunked up or dont open all the way. If you have good water pressure to ... Bosch Dishwashers

We have a Siemens dishwasher SE25M851. It had the check water light on, so we have checked all water flows which seem fine. There is what I think is an Aquastop connected to the water hose, which I have no idea if the problem is there, but when I now put the dishwasher on there is a burning smell coming out of it, so have had to turn off power supply. Can you shed any light to the problem?


... Siemens Dishwashers

Jackson jp-24b purchased this machine used, cant figure out how to work it. I flip the auto cycle on, and then the power switch. The fill light turns green and i assume water is filling up in the machine. In the meantime there are two small red external hoses that hot water comes and i currently just have those hanging in the sink. At the same time, nothing is happening during the wash cycle, the wash gauge doesnt even move only the rinse gauge. Also when i try to drain it nothing happends (begi


It needs a new drain relay box 120 volt the drain is stuck open the jp 24 were not very good machines the red lines are drain lines if you plug up the drian lines at fillup the machine will wash but now it will never drain a new drain box is not c ... Jackson JP-24B Built-in Dishwasher

Frigidaire Dishwasher won't start (lights cycle but no water/motor) Model Number: FDB1050REB2 Brand: Frigidaire Our dishwasher is 1.25 years old and already not working (grrr!). When it is turned on, the lights cycle through like a normal wash cycle, but the motor isn't engaged nor does any water cycle through. This happened about a month ago and I took everything apart to make sure all of the connections were secure and it started working again...not this time. Any ideas?


... Frigidaire Dishwashers

The dishwasher lights turn on but when I press "normal" nothing happens, the "dry" sign is on but not "wash" and rinse' I bought the machine second hand so I haven't got the manual or the id np. I was told it was a $600 model. Can you help, I don't want to have to buy another one. Elizabeth .


May I get the name of the buttons on the dishwasher to help you more. It sounds like the child lock is on and needs to be turned off. Please reply with the button names.\015\012\015\012thank you ... LG Dishwashers

My dishwasher will start any program, it drains, fills, empties & beeps continually within a few minutes. The rinse light stays on until the machine is turned off & re-set. Aditonally, the ater heating has been hit & miss for some time! A service guy cleaned the water sensor with hot water fro a ketle + tooth brush, but the problem came back after a couple of weeks. Having removed item he cleaned, it looks fine and appears to switch OK. Not sure if its actually faulty. Is the themperature sensor


... Whirlpool 24 in. ADG7540 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1786 seconds