Having problems with your Dishwashers ?

Water remains in the bottom of the dishwasher after a wash cycle. We just put in a new disposal - works great! Hose is connected inthe correct place and seems to be free of gunk.


Answers :

Hello sschneid,
\015\012New disposals have a knockout plug at the point of entry for the dishwasher, I assume you knew that and removed it. If not, then detach the dishwasher drain hose from the disposal and take off the hose adapter from the body of the disposal assembly.. with power disabled.. use a screwdriver to push the knockout plug out and remove it from the disposal grind compartment. Manufacturers leave that in there for peopel who need a disposal but don't have a dishwasher. Get back to me if that is not the solution and I wil help you resolve it..
\015\012Regards,
\015\012Rick
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water remains in the bottom of the dishwasher after a wash cycle. We just put in a new disposal - works great! Hose is connected inthe correct place and seems to be free of gunk.


Hello sschneid,\015\012New disposals have a knockout plug at the point of entry for the dishwasher, I assume you knew that and removed it. If not, then detach the dishwasher drain hose from the disposal and take off the hose adapter from the bo ... Dishwashers

I just bought a used LG LDS 5811ST stainless steel built in dishwasher. The previous owner said he bought it 4 years ago. It's in great shape but doesn't work. It powers up but the water is not pumping into the dishwasher. The previous owner said that he thought it was the pump. He said he took it apart once and cleaned a bunch of crud out of some hoses and it worked for a while then started making funny noise and stopped. When i got it home i powered it up and connected water hose. It seems to


Rom the Service Manual:"1E INLET ERROR Not reached to the normal water level in spite of 10 min. water supply.The Hall sensor is OK?Check the frequency of Inlet Water by the Test Mode." ... Dishwashers

Soap feed The soap feed hose on my Karcher 2650 does not suck up the soap into the washer. I pulled off the connector piece that the hose is connected to. I can blow through the hose. There is a little metal finger thing that you can tell pushes up into place when the water pressure is high. It seems like it is supposed to drop down and allow some soap through when the water is running. I found a loose(attached to nothing) gasket, looks like a little donut. It was just free floating in t


I fixed mine works good too, watch my video step by step i put it on youtube ... Karcher G2650HHR Gas Pressure Washer

Hello. my dishwasher leaves gunk on the inside of glasses that were wiped clean before washing. It seems like that would mean the drain to the disposal is clogged but the hose is clear and the impellar is free. I blew on the hose and got movement in the disposal. the impellar is clean and new looking. I thought it would be a little dirty? Any help would be greatly appreciated. I will answer any question you have in case i didn't explain it well.


There are many probable causes of failure .A dishwasher's water inlet valve is its most common part to fail. When \015\012your dishes are not being fully cleaned, quite often a faulty water \015\0 ... Dishwashers

I have a Karcher K3.91M pressure washer that pulsates when the trigger is released (off). It works fine when turned on, pressure seems OK. Before this started the unit would just turn off until I again wanted to use it. Is it a problem ? Correctable? All connections seem tight & I see no leakage.


... Karcher K 5.85 M Electric Pressure Washer

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe


... Hobart AM14-253 Free-standing Dishwasher

I have the GLD 4560 NSS and it is no longer draining. The tub stays completely full. When you start it, the water in the tub is reused then it does not drain. No noise or anything when the draining or filling should actually be taking place. Hoses are not kinked, no leaks, no air vent, it drains directly to the disposal. Everything seems OK but it is full of water. Any help would be greatly appreciated.


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

I have model 1380 and it has worked great. We recently moved and now want to use it, but it has been unused for over 3 years. Got it all hooked up and greased the o-rings and plugged it in and it will not start. I can't reset the GFCI as it does not seem to move or do anything. Any suggestions on what my problem may be and how do I correct it, short of buying another unit? Joe


... Campbell Hausfeld 1,350 Psi Electric Pressure Washer With Auto Detail Kit #PW1350

Karcher 2.35. used it for about an hour, working fine. Suddenly motor stopped. Checked fuse and conections...all good but no go. Disconnected water hose and gave it a rest. As I was putting it away, connected to power and motor worked. Connected hose and motor won't work!! HELP! Thank you, Cliff Taylor


... Karcher Pressure Washers

Hello i have a Miele Automatic G579, Every time i try to connect the water hose to the tap it never seem to be tight enough as it always leaks, i have a standard tap for UK and the hose connect dose fit just right but always seems to leak ?


Is the washer in the fitting missing? ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

My lower rack will not clean bowls or cups and I have to be very careful how I place plates. The serviceman has been out twice and I have run vinegar through multiple times with no improvement. My top rack is working fine. I have tried running it on different settings and we have verified that the lower wash arm seems to be spinning. The temperature seems to be fine. Even glasses placed on the lower rack that weren't very dirty seem to have a scum in them when finished. Any ideas?


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Dishwashers

I installed according to guide, but dishwasher will not fill with water. Pump sounds much too loud to be normal. Wiring was checked three times for correct connections. Water supply was checked twice for water getting through, no leaks and water supply on. Drain hose is connected correctly and is connected to house drain.


You state the water supply is on.\015\012Have you loosened the compression nut at the dishwasher ell to see if you have pressure to the water inlet to the dishwasher?\015\012Remember the dishwasher will always run a little to make sure an ... Whirlpool GU2400XTP Built-in Dishwasher

Dish Washer, Electrolux Home Products, Model FDB2510LCC0, Serial NO: 7H34962223 Machine does not drain or add water. The machine has been worked for a couple of years. I checked the following: 1. Overfill Protector not stuck 2. Motor turns on and the machine cycles correctly 3. Since the machine has been running correctly the unit is hooked up correctly: hoses, garbage disposal, knockout plug. Again everything has worked and the motor does cycle and the machine will perform the different cycles


... Electrolux 23 in. ESI602 Free-standing Dishwasher

No pressure, the inlet filter is clean, all hoses and connections are tight, oil levels are correct, hose size to pump is correct with no kinks. Has the pump gone?


In this case it sounds as though either your unloader valve has failed, the water seals have failed or the check valves in the pump need replaced. Unfortunately there are no tests that can be done on this unit to verify which component has failed bec ... Karcher 4000 PSI 36 GPM Gas Pressure Washer G 4000 OH

I have a washer model 1805 (1800 PSI). Everything works but there is always leaking of water (sprays) when I use it. The leak is not from where the water hose connects to the washer, but where the black piece attached to the hose is connected to the body of the washer. I can still do a decent job of power washing, but am wondering if the leaking of water is reducing the power of the washer.


Yes, leaking water will reduce the pressure. Sounds like you need to replace the O-Ring inside the connections on the pump. This is where the pressure hose connects to the pump. If you look carefully inside that connection you will see an O-Ring. Use ... Campbell Hausfeld PW1805 1800 PSI 15 GPM Pressure Washer

Hi, I have a Karcher 3.75 jubilee powerwasher, there is water coming out from where the high pressure hose connects to the machine and the unit pulses when idling but works perfectly without drop in water pressure, when trigger on gun is pulled, on closer examination the metal connection on the hose turns, is this the problem or something else. thank you.


... Karcher Pressure Washers

I have a Bosch SHU8805UC/14 dishwasher. I took the front door panel off to install it better but ended up with two extra pieces that look like either part 935400 Door Guard, or 935526 Support. I cannot seem to find any place on the inside of the door where these pieces would fit. The dishwasher works fine but seems like it got noisier after I put it back together without these two parts. Can you help me locate the proper place for these 2 plastic parts?


Hello, \015\012\015\012Welcome to FixYa.\015\012\015\012I believe the parts you are referring to are likely the blocks in each corner of the outer door panel. These have been a sticking point for many I tech over ... Bosch Dishwashers

Bosch SHX45M05UC/48 I'm trying to install my dishwasher....but, the hose attached to the right side of the dishwasher looks like it should be connecting, at the other end, to another place within the dishwasher. I can't figure out where it connects and I'm sure I shouldn't have two drainage hoses. Help. mm


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

We have a 2500 6.5 briggs & stratton pressure washer. Was working great, changed hydrants & hoses. Now it won't spray water. Yes we went back to the orignial hose & hydrant. Still won't work. Got any suggestions?


... Briggs & Stratton 3000 PSI Pressure Washer

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

I have a Kracher K 4000 GS pressure washer and it seems to have been fine until today. When I start it and squeeze the trigger there is nor pressure, water comes out but as it would normally from the hose. The engine does not even seem to be under load. I used it the other day and got pressure when I picnhed off the soap hose but that did not work this time.


... Karcher G3025OH Pressure Washer

Hi, I have a 10yr old Neff s5543 built-in dishwasher, it is has been working fine but recently has stopped fully draining. I have removed it from the housing and checked all pipe work is unblocked and not kinked, have also blown back down drain tube to free any blockages from drain pipe, have also removed pump cover and checked around impellor for any foreign bodies etc. Everything seems clean and free. I ran a complete heavy cycle (empty dishwasher) and allowed drain pipe to drain into a


Hello there and thank you for choosing fixyaOk there are acouple of things that can be checked on this along with what you have already checkedDrain solenoid\015\012 \015\012 \015\012 \015\ ... Neff 24 in. S5543X2 Built-in Dishwasher

Greetings! My Bosch SHE3305UC/UC12 has worked faithfully until last week when we had to pull it out of its home to retile the floor. Upon reconnecting all of the connections, it no longer works properly. The initial drain cycle works, so the flood switch is fine. But after draining, it just quietly hums. The test cycle actually seems to move to the next step for about 30 seconds, before also just humming. I'm thinking I need to check the valve, but not sure how to do it on this mod


Hi\015\012\015\012The hum sound indicates a bad motor and it should be\015\012replaced. Hope this helps...please post back for further assistance.\015\012\015\012Daniel ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1575 seconds