Having problems with your Dishwashers ?

Water backs up from the sink. pump works but no pressure


Answers :

Your drain hose is backed up in the air gap.. there is either a stainless steel colored thing on your sink or its white that normally you never do anything with. you have to take the 2 caps off of it and clear any debris. if you dont have one then you should get a bucket and take the drain hose off of the drain or the garbage disposal. then clean it out with something like a fridge coil brush (you can pick up at any home store for 10 bucks) then hit the drain button and let it drain into the bucket to make sure its pumping before you reconnect it to the drain. let me know if you need further assistance
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My tappan dishwasher is only 1 1/2 yr old and its not getting at least 1/2 of dishes clean. We have tried everything from changing to liquid soap, increasing water pressure at meter, not using while washing clothes. We used a dishwasher cleaner to remove calcium, and run hot water in sink before using. We know the wand, pump and drain are working. It is model TDB210RFB5 with 1.1A motor. Is the motor too small to clean dishes? I wish I could get my money back or exchange for an upgrade. Thanks!


... Electrolux Dishwashers

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

Water backs up from the sink. pump works but no pressure


Your drain hose is backed up in the air gap.. there is either a stainless steel colored thing on your sink or its white that normally you never do anything with. you have to take the 2 caps off of it and clear any debris. if you dont have one then yo ... Dishwashers

AT FIRST WITH JUST THE WATER ON (PUMP OFF) I SQUEEZE THE WAND AND WATER COMES OUT ABOUT 3 FT. THEN WHEN I START THE PUMP AND SQUEZE THE WAND ONE STRONG SQUIRT COMES OUT THEN GOES BACK TO ABOUT 4 FT. NOT MUCH PRESSURE. CHECKED THE CHECK VALVES, AND THE 3 PISTONS THEY ALL WORK. PUMP NO.AXD 3020


Hi, W/D here.Leave the water on, and hold the trigger down for about 5 minutes to get all of the air out of the system. Letting off of the trigger occasionally and then opening it up will help displace any air in the chambers. While still hol ... Comet Axd3020g Pressure Washer Pump 27 Gpm 2000 Psi

Lost pressure and seems to have water in pump oil (milky color) Working fine one minute then pressure dropped and won't come back


... Comet Pressure Washers

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started. I have the same problem. Water flows thru the pump when not running, but no flow or goes in by-pass mode when I start the pump. The pump being Troy Bilt Model 020296-01. I replaced unloader valve even. Anything else I can do?


You replaced the unloaded valve. Are you positive you have the unloader screwed to pressure and not turned the opposite way? You will have no pressure if it is adjusted wrong. One other thing I have encountered is that the unloader has a ball bearing ... Pressure Washers

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

The water is not draining from machine, although the pump is obviously trying. It doesn't sound quite right. Kind of a growling noise. It can pump water into tubs when experimenting with ideas, but can't pump hard enough to pump the water into the sink. This is all done with the hose removed so we could check for debris in the line. I've checked the filters and they are clean and clear. This is a used machine a friend gave me, and it's been working beautifully until now.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bosch 24 in. SMU40 Built-in Dishwasher

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Low Pressure with no hose attached, pressure is good, attach hose without wand and pressure drops 50%. Have had pump apart 10 times, have checked bypass valve, have even removed bypass and filled passage way so water could not bypass wihout any change. Am down to thinking pump casting is cracked allowing bypassing to happen. Does each of the three piston chambers have a check valve so one piston is not pumping back into another piston chamber?


I worked at a tool rental while attending college and had the opportunity to work on a variety of pressure washers, however, they were of the commercial type. Commercial washers are slightly different in that they usually have seperated components fo ... Karcher 2500 PSI Pressure Washer

Water pressure? I read somewhere that low pressure of the incoming water will make it so that the items on the top drawer will not be as clean. I don't see how this can be the case, as I thought that the way the washer worked was that the washer filled (at whatever speed) and then the machine itself pumped the water through the system at the appropriate pressure. Please clarify.


Mom...not true. The water fills the machine which then uses its own pump to spray the dishes with the water/detergent. If your dishes are not getting clean, use the recommended amount of detergent. Hard water will require a spot treatment like Jet ... KitchenAid KUDR01TJ Dishwasher

Appliance had been working fine now all of a sudden no water is running in the dishwasher.The machine appears to run through all of its cycles but without water. The water pressure in the ajoining sink appears a little low though the water pressure in the rest of my home is fine. I see no water leakage anywhere. Do I need to call an appliance tech or should I call a plumber? Thank you.


... GE GSD1000 Dishwasher

Our kitchen drain clogged recently and water drained back into our VUD141 dishwasher. A plumber cleared the drain, and turned on the DW - which pumped out the standing water. But now, we have no water flowing into the dishwasher. The drain pumps, the heater works, but there's no water supply. The plumber who cleared the drain said he didn't DO dishwashers, and I cannot locate the owner's manual since we prepared for a move.


Hi\015\012\015\012 \015\012\015\012When the dishwasher won't fill and the water supply is on,\015\012then the issue is with the water inlet valve which is either clogged or\015\012blocked, you can try to clean it. If this wont so ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Troy-Bilt 2550 20293 pressure washer not producing pressure. Worked when last used 2 months ago. Pump pistons are moving up and down when engine is pulled through. Inlet water is flowing through pump but no pressure when engine is started.


Ok I wasnt satisfied w/ the previous answer so I did some digging. I took off all the hose attachments and drained the line. I then checked for any clogging in ALL the screens. As usual the wand screen was clogged. this is an easy fix w/ a safety pin ... Pressure Washers

A GE triton dishwasher causes hammer noise when stops filling. The sink faucet works fine as do all the other faucets in the house. I cleaned all of the traps in the dishwasher. Because the sink works, I don't think it is a sink valve problem. I turned off the water to the house and drained the system, the air chambers should be good. Is there some component of the dishwasher that could be causing the noise? Would cleaning the pump help? If so, how would I do that?


The cause of the hammering noise, (slamming) is due to the water inlet valve on the Dishwasher (DW) shutting off abrutly once the DW reaches the proper amount of water.\015\012\015\012If this is an older DW, you might want to replace the ... GE Dishwashers

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

My GE Nautilus DW doesn't fully drain. When it is drained as much as it will it leaves water in the sump at the rear right. If you run the pump at that point, it sucks water out of the sump, but when you open the door and the pump stops water flows back into it. It seems like there is a check valve that isn't working. I have cleaned the sump and the screen which runs accross the rear. I also have taken the plunger out and cleaned it. Then I took the housing for the plugner off the bottom. I don'


HI. check the following areas for fualts.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: I ... Dishwashers

GE Mod # GSD22360Z04WW will not drain water. I manually pushed the solenoid down and the pump and motor seemed to run. No water pumped out of the hose that was disconnected from the garbage disposer. I have discovered that the plug for the disposer was not taken out where the dishwasher hose attached. The dish washer stopped working after a new disposer was installed. I rotated the control knob and at no time did the solenoid for the pump operate. It went back to normal position after control kn


... Dishwashers

Dishwasher LFK-011S: First it occasionally gave four beeps (overflow) but no water in bottom or under. I then noticed that with lower water pressure machine worked ok few months. Now last week in the middle of program, drain pump started to run, machine gave four beeps and pump kept running even main switch off. Now when I plug in power cord, the pump starts to run immediatelly


... Fagor LFA013 SS 23 in Builtin Dishwasher

Pump Problem First time I used the pressure sprayer it worked great for about 10 minutes and then water started shooting out the side of the pump. Then I lost pressure.


... Karcher 2500 PSI Pressure Washer

Proline Logic diswasher won't pump out water. Checked the following:- No blockage Pump works OK Pressure switch appears to work OK What other faults could cause this problem.


... Dishwashers

Have a Kenmore Freestanding Dishwasher that was working when hooked up to the sink. When we plumbed it in and connected the electrical directly, we now get an "F4" flashing on the panel with a beeping noise and the pump sounds like it wants to drain but just get a sucking noise. I've tried putting water in it to prime the pump, but still doesn't want to work. Do the codes mean anything, or point to a specific part?


... Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher

Kenmore dishwasher Food particles left on dishes and inside of dishwasher. All functions appear to be working normally. Water pressure OK, drain OK, water temp OK, Etc. Operating dishwasher though a normal cycle without dishes solves the problem for one load, then back to problem. Dishwasher is about 5 yrs old and worked perfectly for 4 yrs. Any advice would be greatly appreciated. Bruce


... Kenmore 17822 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1779 seconds